Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Power Seat)
RM27L0U _58 Vehicle Interior _049342 SEAT _0235862 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  DISASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for the LH side and RH side.

·

The procedure listed below are for the LH side.



PROCEDURE

Hide 89952 1.REMOVE OCCUPANT CLASSIFICATION ECU (for Front Passenger Side)

Hide 89178A 2.REMOVE SEAT POSITION AIRBAG SENSOR (for Driver Side)

Hide 84921B 3.REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

a.
B201567E01
0.128,1.385 1.140,1.564 1.012,0.179 10 Protective Tape 1.381,1.492 1.768,1.067 false 1.381,1.492 1.768,1.067 false 1.381,1.492 1.768,1.067 false 1.381,1.492 1.768,1.067 false 1.381,1.492 1.768,1.067 false 2.309,1.181 1.381,1.492 1.381,1.492 1.768,1.067 false 1.381,1.492 1.768,1.067 false 1.381,1.492 1.768,1.067 false 1.381,1.492 1.768,1.067 false 1.381,1.492 1.768,1.067 false 1.381,1.492 1.768,1.067 false 2.333,1.173 1.381,1.492 1.381,1.492 1.79,1.043 false

Apply protective tape around the cushion shield.


b.

Using a screwdriver, detach the 2 claws and remove the knob.

HINT:

Tape the screwdriver tip before use.



Hide 84921A 4.REMOVE RECLINING POWER SEAT SWITCH KNOB

a.
B201568E03
2.729,0.823 2.563,1.438 2.563,1.438 2.333,1.26 true 1.958,1.479 3,1.875 1.042,0.396 10 true Protective Tape

Using a screwdriver, detach the 2 claws and remove the knob.

HINT:

Tape the screwdriver tip before use.



Hide 71812D 5.REMOVE FRONT SEAT CUSHION SHIELD LH

a.
B191013

Remove the hog rings and rubber bands of the seatback cover from the seat frame.


b.

Remove the 2 screws.


c.
B166945

Remove the 3 screws.


d.

Detach the 2 claws and remove the cushion shield.


e.

Disconnect the connectors.


Hide 84922A 6.REMOVE FRONT POWER SEAT LUMBAR SWITCH

Hide 84920 7.REMOVE LEG SUPPORT ADJUSTMENT SWITCH (w/ Leg Support Adjustment Switch)

Hide 73240 8.REMOVE FRONT SEAT INNER BELT ASSEMBLY LH

Hide 71862 9.REMOVE FRONT SEAT CUSHION SHIELD INNER LH

a.
B191015

Remove the screw.


b.

Detach the 2 claws and clip, and remove the cushion shield.


Hide 84922C 10.REMOVE FRONT POWER SEAT SWITCH LH

a.
B166949

Disconnect the connectors.


b.

Remove the 3 screws and switch.


Hide 11.REMOVE SEAT CUSHION COVER WITH PAD (w/ Leg Support Adjustment Switch)

a.
B167097

Using a clip remover, remove the 2 clips.


b.
U153238

Disconnect the connector and detach the 2 wire harness clamps.


c.
B191017

Disconnect the connector and detach the 2 wire harness clamps.


d.
B191018

Remove the 4 hog rings and detach the hooks.


e.
B167096

Remove the seat cushion cover wire.


f.

Remove the seat cushion cover with pad from the seat frame.


Hide 12.REMOVE SEAT CUSHION COVER WITH PAD (w/o Leg Support Adjustment Switch)

a.
B167097

Using a clip remover, remove the 2 clips.


b.
U153349

Disconnect the connector and detach the 2 wire harness clamps.


c.
B194826

Disconnect the connector and detach the 2 wire harness clamps.


d.
B191019

Remove the 2 hog rings.


e.

Bend the 2 seat frame claws upward.


f.

Detach the hooks and remove the seat cushion cover with pad.


Hide 71072S 13.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER (w/ Leg Support Adjustment Switch)

a.

Remove the 15 hog rings and front seat cushion cover.

B191020


Hide 71072S 14.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER (w/o Leg Support Adjustment Switch)

a.
B191021

Remove the 10 hog rings and front seat cushion cover.


Hide 87510L 15.REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)

Hide 71931A 16.REMOVE FRONT SEAT HEADREST SUPPORT

a.
B191022

Remove the 3 hog rings.


b.
B191023

Detach the 3 hooks.


c.
B191024

Remove the 2 hog rings and seatback cover wires.


d.
B191055

Detach the 4 claws and remove the 2 headrest supports.


Hide 17.REMOVE SEATBACK COVER WITH PAD

a.
B190986

Lift the seatback cover and remove the nut and detach the seatback cover bracket from the seat frame.


b.

Lift the seatback cover and remove the 4 hog rings and seatback cover with pad.


Hide 71074S 18.REMOVE SEPARATE TYPE FRONT SEATBACK COVER

a.
B195620

Remove the 2 hog rings and seatback cover wires.


b.
B165535

Disconnect the seatback cover bracket from the seatback pad.


c.
B191026

Remove the 2 hog rings and seatback cover from the seatback pad.


Hide 87510N 19.REMOVE FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)

Hide 71876 20.REMOVE RECLINING ADJUSTER INSIDE COVER LH

a.
B201569

Remove the screw.


b.

Detach the claw and remove the reclining adjuster inside cover.


Hide 71876A 21.REMOVE RECLINING ADJUSTER INSIDE COVER RH

HINT:

Use the same procedure for the LH side and RH side.


Hide 71813B 22.REMOVE FRONT SEATBACK SHIELD LH

a.
B201570

Remove the 2 screws.


b.

Detach the claw and remove the front seatback shield.


Hide 71814B 23.REMOVE FRONT SEATBACK SHIELD RH

a.
B191027

Detach the wire harness clamp.


b.

Remove the 2 screws.


c.

Detach the claw and remove the front seatback shield.


Hide 71806C 24.REMOVE FRONT SEAT CUSHION SHIELD SUB-ASSEMBLY LH NO. 2

a.
B201571

Remove the screw.


b.

Detach the hook and remove the cushion shield.


Hide 71806B 25.REMOVE FRONT SEAT CUSHION SHIELD SUB-ASSEMBLY LH NO. 1

HINT:

Use the same procedure for the LH side and RH side.


Hide 72760D 26.REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Climate Control Seat System)

Hide 72760D 27.REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/o Climate Control Seat System)

Hide 85869A 28.REMOVE SEATBACK CLIMATE CONTROL COVER LH NO. 1 (w/ Climate Control Seat System)

a.
B232101

Using a T30 "TORX" socket, remove the 4 "TORX" screws and seatback climate control cover LH No. 1.


Hide 85867A 29.REMOVE SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)

a.
B194060

Detach the clamp.


b.

Using a T30 "TORX" socket, remove the 2 "TORX" screws and remove the seatback climate control blower LH and seatback climate control cover LH No. 3.


Hide 85869A 30.REMOVE SEATBACK CLIMATE CONTROL COVER LH NO. 2 (w/ Climate Control Seat System)

a.
B194062

Detach the 6 clamps and remove the seatback climate control cover LH No. 2.


Hide 85866A 31.REMOVE SEAT CUSHION CLIMATE CONTROL DUCT LH (w/ Climate Control Seat System)

a.
B201572E02
1.302,0.125 1.979,0.292 0.677,0.167 10 false Clamp (B) 0.375,2.417 1.052,2.604 0.677,0.188 10 false Clamp (A) 0.396,1.688 0.594,1.865 0.198,0.177 10 true (1) 1.469,1.073 1.667,1.25 0.198,0.177 10 true (2)

Detach the 2 clamps (A) in the direction indicated by the arrow (1).


b.

Detach the 2 clamps (B) in the direction indicated by the arrow (2).


c.

Detach the 2 claws, and remove the seat cushion climate control duct LH.


Hide 85860 32.REMOVE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY (w/ Climate Control Seat System)

a.
U153153E02
1.271,0.896 1.469,1.104 0.198,0.208 10 true (1) 2.125,0.073 2.323,0.313 0.198,0.24 10 true (2)

Disconnect the connector.


b.

Using a T30 "TORX" socket wrench, remove the "TORX" screw.


c.

Bend the bracket open slightly.


d.

Detach the 2 claws and remove the seat cushion climate control blower by pushing it rearward.


Hide 87501B 33.REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)

a.
B191029

Disconnect the seat heater control connector and detach the clamp.


b.

Detach the clamp and remove the seat heater control.


Hide 82192 34.REMOVE FRONT SEAT WIRE LH (for Driver Side)

a.
B191030

Disconnect the 3 connectors.


b.

Detach the 6 wire harness clamps.


Hide 82191 35.REMOVE FRONT SEAT WIRE RH (for Front Passenger Side)

a.
B191031

Disconnect the 5 connectors.


b.

Detach the 7 wire harness clamps.


Hide 36.REMOVE FRONT POWER SEAT MOTOR ASSEMBLY (for Driver Side)

a.
B232086

Put matchmarks on the seat track rail and sliding unit of the seat frame.


b.
B108592

Connect the positive (+) battery terminal to terminal 1 of the power seat motor and the negative (-) battery terminal to terminal 2 and slide the seat to the foremost position.


c.
B232087

Loosen the 2 nuts.


d.
B108592

Connect the positive (+) battery terminal to terminal 2 of the power seat motor and the negative (-) battery terminal to terminal 1 and slide the seat to the rearmost position.


e.
B231462

Using a 4 mm socket hexagon wrench, remove the 4 bolts.


f.

Remove the 2 nuts and front power seat motor assembly (slide motor).

NOTICE:

Do not apply excessive force to the slide cable (do not bend the slide cable 60° or more).



Hide 37.REMOVE FRONT POWER SEAT MOTOR ASSEMBLY (for Front Passenger Side)

a.
B232088

Put matchmarks on the seat track rail and sliding unit of the seat frame.


b.
B108592

Connect the positive (+) battery terminal to terminal 1 of the power seat motor and the negative (-) battery terminal to terminal 2 and slide the seat to the foremost position.


c.
B232089

Loosen the 2 nuts.


d.
B108592

Connect the positive (+) battery terminal to terminal 2 of the power seat motor and the negative (-) battery terminal to terminal 1 and slide the seat to the rearmost position.


e.
B232090

Using a 4 mm socket hexagon wrench, remove the 4 bolts.


f.

Remove the 2 nuts and front power seat motor assembly (slide motor).

NOTICE:

Do not apply excessive force to the slide cable (do not bend the slide cable 60° or more).