Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM
RM27L0U _58 Vehicle Interior _049342 SEAT _0235879 REAR POWER SEAT CONTROL SYSTEM J

SEAT  REAR POWER SEAT CONTROL SYSTEM  Back Door Courtesy Switch Circuit  


DESCRIPTION

The fold seat control ECU receives signals from the back door courtesy switch and detects the state of the back door (open/close). If the ECU does not detect that the back door is open, the seat folding and return functions are not available.

WIRING DIAGRAM

U153365E02
5.646,3.542 7.094,3.708 1.448,0.167 10 false Fold Seat Control ECU 5.656,0.875 5.958,1.021 0.302,0.146 10 false O34 5.25,0.875 5.521,1.021 0.271,0.146 10 false P20 6.063,0.875 6.479,1.031 0.417,0.156 10 false BDCY 4.24,0.875 4.438,1.031 0.198,0.156 10 false V2 2.948,1.083 3.125,1.24 0.177,0.156 10 false V3 2.948,1.958 3.146,2.146 0.198,0.188 10 false V3 3.198,2.677 4.229,2.854 1.031,0.177 10 false Back Door ECU 3.698,0.885 4.135,1.042 0.438,0.156 10 false OCTY 3.292,1.958 3.719,2.115 0.427,0.156 10 false BDCY 3.281,1.052 3.708,1.208 0.427,0.156 10 false CTYE 1.031,2.875 2.833,3.031 1.802,0.156 10 false - Back Door Courtesy Switch 0.875,1.854 0.99,2.021 0.115,0.167 10 false 3 2.344,1.854 2.469,2.01 0.125,0.156 10 false 4 2.344,2.073 2.448,2.219 0.104,0.146 10 false 6 2.438,1.844 2.594,2.021 0.156,0.177 10 false *3 2.438,2.063 2.594,2.229 0.156,0.167 10 false *4 2.958,1.76 3.146,1.927 0.188,0.167 10 false 10 2.969,0.885 3.146,1.052 0.177,0.167 10 false 20 4.26,0.656 4.448,0.823 0.188,0.167 10 false 17 5.323,0.646 5.438,0.802 0.115,0.156 10 false 5 5.74,0.656 5.854,0.813 0.115,0.156 10 false 5 5.313,1.094 5.49,1.271 0.177,0.177 10 false *2 5.729,1.104 5.875,1.26 0.146,0.156 10 false *1 0.198,3.323 0.948,3.49 0.75,0.167 10 false *1: LH Side 0.198,3.677 1.042,3.844 0.844,0.167 10 false *2: RH Side 0.198,4 2.313,4.167 2.115,0.167 10 false *3: w/o Power Back Door System 0.198,4.323 2.313,4.49 2.115,0.167 10 false *4: w/ Power Back Door System 1.042,2.375 1.292,2.563 0.25,0.188 10 false V5 2.135,1.854 2.417,2.063 0.281,0.208 10 false S 1.063,1.854 1.344,2.063 0.281,0.208 10 false E 1.042,2.521 2.073,2.688 1.031,0.167 10 false Back Door Lock

PROCEDURE

1.READ VALUE USING TECHSTREAM (BACK DOOR COURTESY SWITCH)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Body Electrical / Back Door P/W / Data List.


e.

According to the display on the Techstream, read the Data List.

Back Door P/W
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Back Door Courtesy Switch Back Door Courtesy Switch / ON or OFF ON: Back door opened
OFF: Back door closed
-

OK:

When back door courtesy switch operation is performed, the results are the same as above.




OK

2.CHECK HARNESS AND CONNECTOR (BACK DOOR ECU - FOLD SEAT CONTROL ECU)

NG

GO TO BACK DOOR COURTESY SWITCH CIRCUIT

2.CHECK HARNESS AND CONNECTOR (BACK DOOR ECU - FOLD SEAT CONTROL ECU)
a.

Disconnect the V2 ECU connector.


B443204E01
0.729,1.469 1.031,1.646 0.302,0.177 3.563,1.354 3.906,1.542 0.344,0.188 3.563,1.615 3.917,1.792 0.354,0.177 0.948,2.094 1.271,1.781 true 4.177,0.99 4.729,1.542 true 0.219,0.156 2.458,0.51 2.24,0.354 10 false Front view of wire harness connector: (to Back Door ECU) 4.042,0.177 6.281,0.531 2.24,0.354 10 false Front view of wire harness connector: (to Fold Seat Control ECU) 3.948,1.354 4.135,1.521 0.188,0.167 10 false *1 0.729,2.115 1.146,2.281 0.417,0.167 10 false OCTY 3.74,0.896 4.156,1.063 0.417,0.167 10 false BDCY 3.604,1.365 3.875,1.531 0.271,0.167 10 false O34 3.604,1.625 3.875,1.792 0.271,0.167 10 false P20 3.969,1.615 4.156,1.781 0.188,0.167 10 false *2 3.969,2.104 4.688,2.302 0.719,0.198 10 false *1: LH Side 3.979,2.375 4.698,2.573 0.719,0.198 10 false *2: RH Side 0.792,1.479 1,1.646 0.208,0.167 10 false V2

b.

Disconnect the O34 or P20 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
LH Side
Tester Connection Condition Specified Condition
V2-17 (OCTY) - O34-5 (BDCY) Always Below 1 Ω
V2-17 (OCTY) or O34-5 (BDCY) - Body ground Always 10 kΩ or higher

RH Side
Tester Connection Condition Specified Condition
V2-17 (OCTY) - P20-5 (BDCY) Always Below 1 Ω
V2-17 (OCTY) or P20-5 (BDCY) - Body ground Always 10 kΩ or higher




OK

3.REPLACE BACK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE BACK DOOR ECU
a.

Temporarily replace the back door ECU with a new or normally functioning one (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY).



NEXT

4.CHECK POWER SEAT CONTROL SYSTEM (OPERATION)
4.CHECK POWER SEAT CONTROL SYSTEM (OPERATION)
a.

Check the power folding function (See page Vehicle Interior>SEAT>REAR POWER SEAT CONTROL SYSTEM>OPERATION CHECK).

OK:

Operate normally.




OK

END (BACK DOOR ECU DEFECTIVE)

NG