When the fold seat switch is operated, a switch operation signal is sent to the fold seat control ECU. The ECU receives switch operation signals from each switch and activates the No. 1 power seat motor and No. 2 power seat motor.
Check the No. 1 fold seat switch signal.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O34-15 (RTRN) - Body ground | Back door open
No. 1 fold seat switch LH OFF |
11 to 14 V |
| Back door open
No. 1 fold seat switch LH return |
Below 1 V | |
| O34-16 (FOLD) - Body ground | Back door open
No. 1 fold seat switch LH OFF |
11 to 14 V |
| Back door open
No. 1 fold seat switch LH folding |
Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P20-15 (RTRN) - Body ground | Back door open
No. 1 fold seat switch RH OFF |
11 to 14 V |
| Back door open
No. 1 fold seat switch RH return |
Below 1 V | |
| P20-16 (FOLD) - Body ground | Back door open
No. 1 fold seat switch RH OFF |
11 to 14 V |
| Back door open
No. 1 fold seat switch RH folding |
Below 1 V |
Check No. 2 fold seat switch signal.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O34-10 (FLD2) - Body ground | Rear LH door open
No. 2 fold seat switch LH OFF |
11 to 14 V |
| Rear LH door open
No. 2 fold seat switch LH folding |
Below 1 V | |
| O34-14 (RTN2) - Body ground | Rear LH door open
No. 2 fold seat switch LH OFF |
11 to 14 V |
| Rear LH door open
No. 2 fold seat switch LH return |
Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P20-10 (FLD2) - Body ground | Rear RH door open
No. 2 fold seat switch RH OFF |
11 to 14 V |
| Rear RH door open
No. 2 fold seat switch RH folding |
Below 1 V | |
| P20-14 (RTN2) - Body ground | Rear RH door open
No. 2 fold seat switch RH OFF |
11 to 14 V |
| Rear RH door open
No. 2 fold seat switch RH return |
Below 1 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 1 fold seat switch signal) | B |
| NG (No. 2 fold seat switch signal) | C |
A
B
C
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Body Electrical / Back Door P/W / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Back Door Courtesy Switch | Back Door Courtesy Switch / ON or OFF | ON: Back door opened
OFF: Back door closed |
- |
When back door courtesy switch operation is performed, the results are the same as above.
OK
NG
Remove the No. 1 fold seat switch (See page Vehicle Interior>SEAT>POWER SEAT SWITCH(for Rear No. 2 Seat)>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 6 (FOLD) - 4 (E) | No. 1 fold seat switch LH fold | Below 1 Ω |
| No. 1 fold seat switch LH OFF | 10 kΩ or higher | |
| 7 (RTRN) - 4 (E) | No. 1 fold seat switch LH return | Below 1 Ω |
| No. 1 fold seat switch LH OFF | 10 kΩ or higher |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3 (FOLD) - 5 (E) | No. 1 fold seat switch RH fold | Below 1 Ω |
| No. 1 fold seat switch RH OFF | 10 kΩ or higher | |
| 4 (RTRN) - 5 (E) | No. 1 fold seat switch RH return | Below 1 Ω |
| No. 1 fold seat switch RH OFF | 10 kΩ or higher |
OK
NG
Disconnect the O34 or P20 ECU connector.
Disconnect the O27 or O28 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O34-15 (RTRN) - O27-7 (RTRN) | Always | Below 1 Ω |
| O34-15 (RTRN) - Body ground | Always | 10 kΩ or higher |
| O34-16 (FOLD) - O27-6 (FOLD) | Always | Below 1 Ω |
| O34-16 (FOLD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P20-15 (RTRN) - O28-4 (RTRN) | Always | Below 1 Ω |
| P20-15 (RTRN) - Body ground | Always | 10 kΩ or higher |
| P20-16 (FOLD) - O28-3 (FOLD) | Always | Below 1 Ω |
| P20-16 (FOLD) - Body ground | Always | 10 kΩ or higher |
OK
NG
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Body Electrical / Main Body / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| RL Door Courtesy SW | Rear door courtesy light switch LH signal / ON or OFF | ON: Rear door courtesy light switch LH ON
OFF: Rear door courtesy light switch LH OFF |
- |
| RR Door Courtesy SW | Rear door courtesy light switch RH signal / ON or OFF | ON: Rear door courtesy light switch RH ON
OFF: Rear door courtesy light switch RH OFF |
- |
When rear door courtesy light switch operation is performed, the results are the same as above.
OK
NG
Remove the No. 2 fold seat switch (See page Vehicle Interior>SEAT>POWER SEAT SWITCH(for Rear No. 2 Seat)>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 6 (FOLD) - 4 (E) | No. 2 fold seat switch LH fold | Below 1 Ω |
| No. 2 fold seat switch LH OFF | 10 kΩ or higher | |
| 7 (RTRN) - 4 (E) | No. 2 fold seat switch LH return | Below 1 Ω |
| No. 2 fold seat switch LH OFF | 10 kΩ or higher |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3 (FOLD) - 5 (E) | No. 2 fold seat switch RH fold | Below 1 Ω |
| No. 2 fold seat switch RH OFF | 10 kΩ or higher | |
| 4 (RTRN) - 5 (E) | No. 2 fold seat switch RH return | Below 1 Ω |
| No. 2 fold seat switch RH OFF | 10 kΩ or higher |
OK
NG
Disconnect the O34 or P20 ECU connector.
Disconnect the O26 or P12 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O34-10 (FLD2) - O26-6 (FOLD) | Always | Below 1 Ω |
| O34-10 (FLD2) - Body ground | Always | 10 kΩ or higher |
| O34-14 (RTN2) - O26-7 (RTRN) | Always | Below 1 Ω |
| O34-14 (RTN2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P20-10 (FLD2) - P12-3 (FOLD) | Always | Below 1 Ω |
| P20-10 (FLD2) - Body ground | Always | 10 kΩ or higher |
| P20-14 (RTN2) - P12-4 (RTRN) | Always | Below 1 Ω |
| P20-14 (RTN2) - Body ground | Always | 10 kΩ or higher |
OK
NG