Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM27L0U _58 Vehicle Interior _049344 HEATING / AIR CONDITIONING _0235901 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1417/17  Rear Evaporator Temperature Sensor Circuit  


DESCRIPTION

The No. 2 air conditioning harness (rear evaporator temperature sensor) is installed on the evaporator in the rear air conditioning unit to detect the temperature of the cooled air that has passed through the evaporator and to control the rear air conditioner. It sends signals to the air conditioning amplifier. The signals change in accordance with the resistance of the No. 2 air conditioning harness (rear evaporator temperature sensor). As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases. The air conditioning amplifier applies a voltage (5 V) to the No. 2 air conditioning harness (rear evaporator temperature sensor) and reads voltage changes as changes in the resistance of the No. 2 air conditioning harness (rear evaporator temperature sensor). This sensor is used for frost prevention.

DTC Code DTC Detection Condition Trouble Area
B1417/17 Open or short in rear evaporator temperature sensor circuit
·

No. 2 air conditioning harness (rear evaporator temperature sensor)

·

Harness or connector between No. 2 air conditioning harness (rear evaporator temperature sensor) and air conditioning amplifier

·

Air conditioning amplifier



WIRING DIAGRAM

E127591E06
5.397,0.828 5.692,1.010 0.295,0.181 10 TEC 5.397,1.437 5.815,1.618 0.418,0.181 10 SGND 5.082,2.22 6.697,2.413 1.615,0.192 10 Air Conditioning Amplifier 1.179,2.236 3.163,2.413 1.984,0.177 10 No. 2 Air Conditioning Harness 0.876,0.492 3.226,0.673 2.350,0.181 10 Rear Evaporator Temperature Sensor 5.16,0.75 5.316,0.931 0.156,0.181 10 4 5.147,1.368 5.318,1.549 0.171,0.181 10 19 4.221,1.35 4.377,1.531 0.156,0.181 10 7 4.206,0.745 4.362,0.926 0.156,0.181 10 8 4.043,0.741 4.199,0.922 0.156,0.181 10 + 4.048,1.372 4.204,1.553 0.156,0.181 10 - 1.179,2.088 1.400,2.241 0.221,0.153 10 P9 5.082,2.069 5.374,2.215 0.291,0.145 10 H67

PROCEDURE

1.READ VALUE USING TECHSTREAM (EVAP TEMP SENSOR (REAR))
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List / Evap Temp Sensor (Rear).


e.

According to the display on the Techstream, read the Data List.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Evap Temp Sensor (Rear) Rear evaporator fin thermistor /
Min.: -29.7°C (-21.46°F)
Max.: 59.6°C (139.28°F)
Actual evaporator temperature is displayed Open circuit: -29.7°C (-21.46°F)
Short circuit: 59.6°C (139.28°F)

OK:

The display is as specified in the normal condition.


Result
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC output) C



A

2.INSPECT NO. 2 AIR CONDITIONING HARNESS (REAR EVAPORATOR TEMPERATURE SENSOR)

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C

2.INSPECT NO. 2 AIR CONDITIONING HARNESS (REAR EVAPORATOR TEMPERATURE SENSOR)
a.

Remove the No. 2 air conditioning harness (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT>DISASSEMBLY).

E345194E01
0.75,1.583 1.26,0.906 false 2.5,2.698 2.458,2.167 true 2.594,2.698 2.833,2.167 true 0.552,0.135 3.01,0.875 2.458,0.74 10 false Component without harness connected: (No. 2 Air Conditioning Harness) 1.313,0.802 2.938,1.5 1.625,0.698 10 false Rear Evaporator Temperature Sensor Area 2.271,2.052 2.729,2.25 0.458,0.198 10 false (+) 2.875,2.042 3.302,2.24 0.427,0.198 10 false (-) 4.208,0.292 6.5,0.49 2.292,0.198 10 false Resistance (kΩ) 4.156,0.979 4.771,1.177 0.615,0.198 10 false 10.0 4.229,1.156 4.771,1.354 0.542,0.198 10 false 9.0 4.229,1.354 4.771,1.563 0.542,0.208 10 false 8.0 4.229,1.531 4.771,1.719 0.542,0.188 10 false 7.0 4.229,1.708 4.76,1.906 0.531,0.198 10 false 6.0 4.229,1.885 4.771,2.083 0.542,0.198 10 false 5.0 4.229,2.063 4.781,2.271 0.552,0.208 10 false 4.0 4.229,2.25 4.792,2.458 0.563,0.208 10 false 3.0 4.229,2.427 4.781,2.625 0.552,0.198 10 false 2.0 4.229,2.615 4.771,2.823 0.542,0.208 10 false 1.0 4.229,2.792 4.781,3 0.552,0.208 10 false 0.0 4.333,2.979 4.792,3.177 0.458,0.198 10 false -10 4.99,2.99 5.396,3.188 0.406,0.198 10 false 0 5.542,2.99 5.979,3.188 0.438,0.198 10 false 10 6.135,2.99 6.552,3.198 0.417,0.208 10 false 20 6.646,2.99 7.104,3.188 0.458,0.198 10 false 30 4.313,3.167 4.927,3.365 0.615,0.198 10 false (14) 4.917,3.167 5.531,3.365 0.615,0.198 10 false (32) 5.51,3.167 6.125,3.365 0.615,0.198 10 false (50) 6.104,3.167 6.719,3.365 0.615,0.198 10 false (68) 6.604,3.167 7.156,3.354 0.552,0.188 10 false (86) 4.781,3.406 6.094,3.635 1.313,0.229 10 false Temperature °C (°F)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (-) - 8 (+) -10°C (14°F) 7.30 to 9.10 kΩ
-5°C (23°F) 5.65 to 6.95 kΩ
0°C (32°F) 4.40 to 5.35 kΩ
5°C (41°F) 3.40 to 4.15 kΩ
10°C (50°F) 2.70 to 3.25 kΩ
15°C (59°F) 2.14 to 2.58 kΩ
20°C (68°F) 1.71 to 2.05 kΩ
25°C (77°F) 1.38 to 1.64 kΩ
30°C (86°F) 1.11 to 1.32 kΩ


HINT:
·

Touching the thermistor even slightly may change the resistance value. Be sure to hold the connector of the thermistor.

·

When measuring, the thermistor temperature must be the same as the ambient temperature.

·

As the temperature increases, the resistance decreases (see the graph).




c.

Reinstall the No. 2 air conditioning harness.



OK

3.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER)

NG

3.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the P9 No. 2 air conditioning harness connector.

E345195E01
0.521,1.563 0.927,1.813 0.406,0.25 3.417,1 3.792,1.208 0.375,0.208 1.76,2.052 2.344,1.531 true 1.885,2.073 2.375,1.896 true 3.99,2.375 4.417,1.969 true 4.865,2.365 4.594,1.906 true 0.5,0.156 2.865,0.844 2.365,0.688 10 false Front view of wire harness connector: (to No. 2 Air Conditioning Harness (Rear Evaporator Temperature Sensor)) 0.656,1.604 0.969,1.802 0.313,0.198 10 false P9 3.49,1.021 3.792,1.177 0.302,0.156 10 false H67 4.104,0.156 6.385,0.865 2.281,0.708 10 false Rear view of wire harness connector: (to Air Conditioning Amplifier) 2.385,1.427 2.844,1.625 0.458,0.198 10 false (-) 2.438,1.802 2.896,2 0.458,0.198 10 false (+) 3.875,2.396 4.49,2.594 0.615,0.198 10 false SGND 4.865,2.375 5.479,2.573 0.615,0.198 10 false TEC


b.

Disconnect the H67 air conditioning amplifier connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P9-8 (+) - H67-4 (TEC) Always Below 1 Ω
P9-7 (-) - H67-19 (SGND) Always Below 1 Ω
P9-8 (+) or H67-4 (TEC) - Body ground Always 10 kΩ or higher
P9-7 (-) or H67-19 (SGND) - Body ground Always 10 kΩ or higher



d.

Reconnect the air conditioning amplifier connector.


e.

Reconnect the No. 2 air conditioning harness connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR