Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM27L0U _58 Vehicle Interior _049344 HEATING / AIR CONDITIONING _0235901 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1422/22  Compressor Lock Sensor Circuit  


DESCRIPTION

The ECM sends a engine speed signal to the air conditioning amplifier via the CAN communication system.

The air conditioning amplifier reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier determines that the compressor locks, and turns the magnetic clutch off.

DTC Code DTC Detection Condition Trouble Area
B1422/22 Open or short in compressor lock sensor circuit
·

Air conditioning compressor (lock sensor)

·

Compressor drive belt

·

Harness or connector between air conditioning compressor (lock sensor) and air conditioning amplifier

·

Air conditioning amplifier

·

CAN communication system



WIRING DIAGRAM

E146212E02
2.711,2.815 3.108,2.952 0.397,0.137 10 ECM 3.96,2.451 4.616,2.588 0.656,0.137 10 CAN Line 5.087,2.815 6.827,2.952 1.739,0.137 10 Air Conditioning Amplifier 0.259,1.619 0.695,1.757 0.437,0.137 10 D39 1.8,0.461 1.947,0.599 0.147,0.137 10 1 1.8,1.003 1.947,1.140 0.147,0.137 10 2 5.23,0.56 5.685,0.698 0.455,0.137 10 LOCK 5.23,1.102 5.685,1.239 0.455,0.137 10 SG-2 4.81,0.56 5.084,0.698 0.274,0.137 10 H24 4.81,1.102 5.084,1.239 0.274,0.137 10 H24 4.887,0.374 5.085,0.511 0.198,0.137 10 8 4.855,0.919 5.053,1.057 0.198,0.137 10 13 1.282,0.685 1.719,0.823 0.437,0.137 10 SSR+ 1.282,1.227 1.719,1.365 0.437,0.137 10 SSR- 0.259,1.797 2.167,1.934 1.909,0.137 10 Air Conditioning Compressor 0.259,1.974 1.998,2.112 1.739,0.137 10 (Lock Sensor)

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Connect the Techstream to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Select "Communication Bus Check"

OK:

All ECUs and sensors connected to the CAN communication system are displayed.



Result
Result Proceed to
CAN system is normal A
CAN system is abnormal B


A

2.CHECK AIR CONDITIONING AMPLIFIER

B

2.CHECK AIR CONDITIONING AMPLIFIER
U153930E01
1.781,0.861 2.085,1.019 0.304,0.159 10 H24 2.091,1.456 2.511,2.315 false 2.343,2.35 2.977,2.515 0.634,0.165 10 LOCK 0.046,0 2.395,0.349 2.349,0.349 10 Component with harness connected: (Air Conditioning Amplifier) 1.783,1.459 1.346,2.287 false 1.11,2.325 1.471,2.483 0.361,0.158 10 SG-2

a.

Remove the air conditioning amplifier with the connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


E147483E01
2.91,0.901 3.243,1.043 0.332,0.142 10 GND 2.391,0 3.218,0.146 0.826,0.146 10 200 mV/DIV. 1.309,1.877 2.067,2.051 0.757,0.174 10 10 ms./DIV.

b.

Using an oscilloscope, check the waveform.

Compressor Lock Signal
Terminal Name LOCK - SG-2
Tester Range 200 mV/DIV., 10 ms./DIV.
Condition Engine is running
Blower switch LO
A/C switch ON

Result
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC output) C


c.

Remove the air conditioning amplifier.



A

3.INSPECT AIR CONDITIONING COMPRESSOR (LOCK SENSOR)

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C

3.INSPECT AIR CONDITIONING COMPRESSOR (LOCK SENSOR)
E005280E33
1.885,1.073 2.375,1.073 true 1.063,1.083 1.542,1.083 true 0.313,0.063 2.906,0.396 2.594,0.333 10 false Component without harness connected: (Air Conditioning Compressor) 2.417,0.99 2.885,1.156 0.469,0.167 10 false SSR+ 0.646,1.01 1.031,1.177 0.385,0.167 10 false SSR-

a.

Disconnect the D39 air conditioning compressor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SSR+) - 2 (SSR-) 20°C (68°F) 165 to 205 Ω



c.

Reconnect the air conditioning compressor connector.



OK

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - AIR CONDITIONING COMPRESSOR)

NG

REPLACE AIR CONDITIONING COMPRESSOR (LOCK SENSOR)

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - AIR CONDITIONING COMPRESSOR)
a.
E344839E02
0.76,1.698 1.104,1.906 0.344,0.208 0.625,3.792 0.969,4 0.344,0.208 2.073,1.813 2.573,2.167 true 1.76,1.813 1.385,2.167 true 1.5,3.958 1.125,4.313 false 1.906,3.958 2.406,4.313 false 0.531,0.042 2.771,0.438 2.24,0.396 10 false Rear view of wire harness connector: (to Air Conditioning Amplifier) 0.656,2.479 2.938,2.875 2.281,0.396 10 false Front view of wire harness connector: (to Air Conditioning Compressor) 1.167,2.188 1.594,2.427 0.427,0.24 10 false SG-2 2.417,2.177 2.844,2.417 0.427,0.24 10 false LOCK 0.823,1.719 1.156,1.906 0.333,0.188 10 false H24 0.677,3.802 1.01,3.99 0.333,0.188 10 false D39 0.833,4.333 1.26,4.573 0.427,0.24 10 false SSR+ 2.271,4.333 2.698,4.573 0.427,0.24 10 false SSR-

Disconnect the H24 air conditioning amplifier connector.


b.

Disconnect the D39 air conditioning compressor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H24-8 (LOCK) - D39-1 (SSR+) Always Below 1 Ω
H24-13 (SG-2) - D39-2 (SSR-) Always Below 1 Ω
H24-8 (LOCK) or D39-1 (SSR+) - Body ground Always 10 kΩ or higher
H24-13 (SG-2) or D39-2 (SSR-) - Body ground Always 10 kΩ or higher



d.

Reconnect the air conditioning amplifier connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR