Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM27L0U _58 Vehicle Interior _049344 HEATING / AIR CONDITIONING _0235901 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1447/47  Rear Air Mix Damper Control Servo Motor Circuit  


DESCRIPTION

The air mix rear damper servo sends pulse signals to indicate the damper position to the air conditioning amplifier. The air conditioning amplifier activates the motor (normal or reverse) based on these signals to move the rear air mix damper to the appropriate position. This adjusts the amount of air passing through the heater core after passing the evaporator and controls the temperature of the blown air.

DTC Code DTC Detection Condition Trouble Area
B1447/47 Rear air mix damper position does not change even if air conditioning amplifier operates rear air mix damper servo motor
·

Air mix rear damper servo

·

No. 2 air conditioning harness

·

Harness or connector between No. 2 air conditioning harness and air conditioning amplifier

·

Air conditioning amplifier



WIRING DIAGRAM

E156903E10
1.39,0.481 1.837,0.623 0.448,0.142 10 SiG. A 1.39,0.778 1.837,0.920 0.448,0.142 10 SiG. B 1.441,1.147 1.799,1.289 0.357,0.142 10 GND 2.414,0.335 2.543,0.491 0.128,0.156 10 2 2.414,0.636 2.543,0.792 0.128,0.156 10 3 2.414,0.963 2.543,1.119 0.128,0.156 10 1 2.414,1.281 2.543,1.437 0.128,0.156 10 4 2.414,1.596 2.543,1.752 0.128,0.156 10 5 2.743,0.335 2.871,0.491 0.128,0.156 10 2 2.743,0.636 2.871,0.792 0.128,0.156 10 3 2.743,0.963 2.871,1.119 0.128,0.156 10 1 2.743,1.281 2.871,1.437 0.128,0.156 10 4 2.743,1.596 2.871,1.752 0.128,0.156 10 5 5.301,0.236 5.498,0.392 0.197,0.156 10 23 5.341,0.864 5.458,1.020 0.117,0.156 10 1 5.304,1.497 5.494,1.653 0.190,0.156 10 21 5.011,0.236 5.130,0.392 0.119,0.156 10 4 5.001,0.864 5.129,1.020 0.128,0.156 10 3 5.001,1.497 5.129,1.653 0.128,0.156 10 2 3.194,0.973 3.392,1.115 0.198,0.142 10 IC 0.568,2.019 2.315,2.218 1.746,0.199 10 Air Mix Rear Damper Servo 5.533,2.113 6.761,2.417 1.228,0.304 10 Air Conditioning Amplifier 5.533,1.964 5.828,2.120 0.295,0.156 10 H67 2.573,2.093 2.867,2.249 0.295,0.156 10 P9 2.569,2.265 5.200,2.413 2.630,0.149 10 No. 2 Air Conditioning Harness 4.488,0.338 4.933,0.494 0.445,0.156 10 RBBU 4.488,0.969 4.933,1.124 0.445,0.156 10 RBUS 4.488,1.613 4.933,1.769 0.445,0.156 10 RBUG 5.569,0.338 6.014,0.494 0.445,0.156 10 RBBU 5.569,0.969 6.014,1.124 0.445,0.156 10 RBUS 5.569,1.613 6.014,1.769 0.445,0.156 10 RBUG

PROCEDURE

1.READ VALUE USING TECHSTREAM (AIR MIX TARG PULSE (R))
a.

Connect the Techstream to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List / Air Mix Targ Pulse (R).


e.

According to the display on the Techstream, read the Data List.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Air Mix Servo Targ Pulse (R) Rear side air mix servo motor target pulse /
Min.: 0, Max.: 255
Customized value displayed -

OK:

The display is as specified in the normal condition.


Result
Result Proceed to
OK (When troubleshooting according to the DTC output) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER)

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C

2.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the P9 No. 2 air conditioning harness connector.

E345195E02
0.521,1.563 0.927,1.813 0.406,0.25 3.417,1 3.792,1.208 0.375,0.208 1.875,1.906 2.427,2.083 true 4.094,2.365 4.177,1.969 true 5.281,2.188 4.792,1.906 true 1.594,1.885 2.427,1.344 true 1.75,1.885 2.427,1.729 true 4.677,2.396 4.292,1.969 true 0.5,0.156 2.865,0.844 2.365,0.688 10 false Front view of wire harness connector: (to No. 2 Air Conditioning Harness) 0.656,1.604 0.969,1.802 0.313,0.198 10 false P9 3.49,1.021 3.792,1.177 0.302,0.156 10 false H67 4.104,0.156 6.385,0.865 2.281,0.708 10 false Rear view of wire harness connector: (to Air Conditioning Amplifier) 2.49,1.26 2.948,1.458 0.458,0.198 10 false RBUG 2.49,2.021 2.948,2.219 0.458,0.198 10 false RBBU 3.875,2.396 4.49,2.594 0.615,0.198 10 false RBBU 4.708,2.375 5.354,2.573 0.646,0.198 10 false RBUG 2.49,1.635 2.948,1.833 0.458,0.198 10 false RBUS 5.333,2.135 5.792,2.333 0.458,0.198 10 false RBUS


b.

Disconnect the H67 air conditioning amplifier connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P9-2 (RBUG) - H67-21 (RBUG) Always Below 1 Ω
P9-3 (RBUS) - H67-1 (RBUS) Always Below 1 Ω
P9-4 (RBBU) - H67-23 (RBBU) Always Below 1 Ω
H67-21 (RBUG) - Body ground Always 10 kΩ or higher
H67-1 (RBUS) - Body ground Always 10 kΩ or higher
H67-23 (RBBU) - Body ground Always 10 kΩ or higher



d.

Reconnect the air conditioning amplifier connector.


e.

Reconnect the No. 2 air conditioning harness connector.



OK

3.REPLACE AIR MIX REAR DAMPER SERVO

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE AIR MIX REAR DAMPER SERVO
a.

Replace the air mix rear damper servo motor (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT>DISASSEMBLY).



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC

OK

END (AIR MIX REAR DAMPER SERVO IS DEFECTIVE)

NG

5.REPAIR OR REPLACE NO. 2 AIR CONDITIONING HARNESS
5.REPAIR OR REPLACE NO. 2 AIR CONDITIONING HARNESS
a.

Repair or replace the No. 2 air conditioning harness (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT>DISASSEMBLY).



NEXT

6.CHECK FOR DTC