Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING
RM27L0U _58 Vehicle Interior _049346 INTERIOR PANELS / TRIM _0235933 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  INSTALLATION  


PROCEDURE

Hide 63310 1.INSTALL ROOF HEADLINING ASSEMBLY (w/o Rear Seat Entertainment System)

B193937

a.

Place the roof headlining into the cabin as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining when placing it in the cabin.



b.

Install the washer hose.


c.

Engage the clip and install the roof headlining.

B193938


d.
B190136

Install the visor holder with the screw.

HINT:

Use the same procedure to install the visor holder on the other side.



e.

Connect the satellite radio antenna connector.


f.
B190127

Engage the 4 clamps to install the amplifier antenna.


g.

Install the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


h.

Connect the connector.


i.
B190126

Install the amplifier antenna with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


j.

Connect the connector.


k.
B190163

Install the washer hose and the amplifier antenna.


l.

Connect the connector.


m.
B190155

Engage the 3 clamps to install the roof wire.


n.

Connect the connector.


Hide 2.INSTALL ROOF HEADLINING ASSEMBLY (w/ Rear Seat Entertainment System)

B193937

a.

Place the roof headlining into the cabin as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining when placing it in the cabin.



b.

Install the washer hose.


c.

Engage the clip and install the roof headlining.

B193938


d.
B190136

Install the visor holder with the screw.

HINT:

Use the same procedure to install the visor holder on the other side.



e.
B190127

Engage the 4 clamps to install the amplifier antenna.


f.

Install the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


g.

Connect the connector.


h.
B190126

Install the amplifier antenna with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


i.

Connect the connector.


j.
B190163

Install the washer hose and the amplifier antenna.


k.

Connect the connector.


l.
B193939

Engage the 3 clamps to install the roof wire.


m.

Connect the 2 connectors.


Hide 3.INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

B193936

a.

Place the roof headlining into the cabin as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining when placing it in the cabin.



b.

Install the washer hose.


c.

Engage the clip and 14 fasteners.

B193935


d.
B190127

Engage the 4 clamps to install the amplifier antenna.


e.

Install the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


f.

Connect the connector.


g.
B190126

Install the amplifier antenna with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


h.

Connect the connector.


i.
B190163

Install the washer hose and the amplifier antenna.


j.

Connect the connector.


k.
B191808

Engage the 3 clamps to install the roof wire.


l.

Connect the 3 connectors.


Hide 87834 4.INSTALL REAR VIEW INNER MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 63379 5.INSTALL ROOF HEADLINING REAR TRIM COVER LH

B193893

a.

Engage the 6 claws to install the roof headlining rear trim cover LH.


Hide 74617Y 6.INSTALL ASSIST GRIP PLUG

B165717

a.

Install a new assist grip plug.


Hide 74610A 7.INSTALL ASSIST GRIP SUB-ASSEMBLY

B169217

HINT:

Use the same procedure for the other 4 assist grips.


a.

Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.


b.

Install the assist grip.


Hide 74310 8.INSTALL VISOR ASSEMBLY RH (w/ Illumination)

B191402

a.

Connect the connector.


b.
B190133

Install the 4 screws and the visor.


Hide 74310 9.INSTALL VISOR ASSEMBLY LH (w/ Illumination)

HINT:

Use the same procedure for both sides.


Hide 74310 10.INSTALL VISOR ASSEMBLY RH (w/o Illumination)

B190135

a.

Install the visor with the 3 screws.


Hide 74320 11.INSTALL VISOR ASSEMBLY LH (w/o Illumination)

HINT:

Use the same procedure for both sides.


Hide 74317 12.INSTALL VISOR BRACKET COVER RH

B166262

a.

Attach the 4 claws to install the visor bracket cover.


Hide 74318 13.INSTALL VISOR BRACKET COVER LH

HINT:

Use the same procedure for both sides.


Hide 81240D 14.INSTALL NO. 2 ROOM LIGHT ASSEMBLY

a.

Connect the connector.


b.

Engage the 2 claws to install the No. 2 room light.


c.

Engage the 2 claws to install the lens.

B193063


Hide 81240 15.INSTALL NO. 1 ROOM LIGHT ASSEMBLY

a.

Connect the connector.


b.

Engage the 4 clips to install the No. 1 room light.


c.

Engage the 4 claws to install the lens.

B193921


Hide 16.INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/ Rear Seat Entertainment System)

B191797

a.

Connect the connector.


b.
B193891

Engage the 4 clips to install the No. 1 room light.


Hide 63650A 17.INSTALL ROOF CONSOLE BOX ASSEMBLY

a.

for Short Type:

Install the roof console box (See page Vehicle Interior>INTERIOR PANELS / TRIM>OVERHEAD CONSOLE BOX>INSTALLATION).


b.

for Long Type:

Install the roof console box (See page Vehicle Interior>INTERIOR PANELS / TRIM>OVERHEAD CONSOLE BOX>INSTALLATION).


Hide 62570D 18.INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY RH

B190123

a.

Engage the 5 clips to install the rear window No. 2 side garnish assembly RH.


b.

Install the bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


c.
B193067

Engage the claw to install the cover.


Hide 62580F 19.INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY LH (w/o Power Back Door)

HINT:

Use the same procedure for both sides.


Hide 62580F 20.INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY LH (w/ Power Back Door)

B191798

a.

Connect the connector.


b.

Engage the 5 clips to install the rear window No. 2 side garnish assembly LH.


c.

Install the bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


d.
B193892

Engage the claw to install the cover.


Hide 62550F 21.INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY RH

B190124

a.

Pass the rear seat outer belt floor anchor through the quarter trim panel.


b.

Engage the 5 clips to install the rear window side garnish.


c.

Install the bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


d.
B193066

Engage the claw to install the cover.


Hide 62560C 22.INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY LH

HINT:

Use the same procedure for both sides.


Hide 62510P 23.INSTALL QUARTER TRIM PANEL ASSEMBLY RH

a.

Connect the connector.


b.

Engage the 11 clips to install the quarter trim panel assembly.


c.

Install the 2 bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


d.

Install the 2 clips.

B219907


e.
B190147

Engage the 2 claws to install the cover.


f.
B190146

Install the outer lap belt anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


g.
B190158

Install the outer lap belt anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


h.
B190145

Engage the 3 claws to install the outer lap belt anchor cover.


Hide 62520P 24.INSTALL QUARTER TRIM PANEL ASSEMBLY LH

a.

Connect the connector.


b.

Engage the 11 clips to install the quarter trim panel.


c.

Install the 2 bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


d.

Install the 2 clips.

B222458


e.
B193068

Engage the 2 claws to install the cover.


f.
B191816

Install the outer lap belt anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


g.
B191818

Install the outer lap belt anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


h.
B193920

Engage the 3 claws to install the outer lap belt anchor cover.


Hide 62510P 25.INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat)

a.

Connect the 3 connectors.


b.

Engage the 11 clips to install the quarter trim panel.


c.

Install the 2 bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


d.

Install the 2 clips.

B222459


e.
B190147

Engage the 2 claws to install the cover.


f.
B190146

Install the outer lap belt anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


g.
B190158

Install the outer lap belt anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


h.
B190145

Engage the 3 claws to install the outer lap belt anchor cover.


Hide 62520P 26.INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for Power Seat)

a.

Connect the 5 connectors.


b.

Engage the 12 clips to install the quarter trim panel.


c.

Install the 2 bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


d.

Engage the 2 clamps to install the wire harness.


e.

Install the 2 clips.

B222460


f.
B193068

Engage the 2 claws to install the cover.


g.
B191816

Install the outer lap belt anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


h.
B191818

Install the outer lap belt anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


i.
B193920

Engage the 3 claws to install the outer lap belt anchor cover.


Hide 58573A 27.INSTALL REAR FLOOR MAT SUPPORT PLATE

B190142

a.

Engage the 5 clips to the 4 claws, and install the rear floor mat support plate.


Hide 66310D 28.INSTALL ROPE HOOK ASSEMBLY

B190141

a.

Install the rope hook with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.
B190139

Engage the 2 claws to install the cover.


Hide 62411 29.INSTALL CENTER PILLAR GARNISH RH

a.

Pass the front seat outer belt floor anchor through the center pillar garnish.


b.

Engage the clip and the guide to install the center pillar garnish.


c.

Install the bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


d.

Install the assist grip with the 2 bolts.

Torque:
9.7 N*m (99 kgf*cm, 86 in.*lbf)


e.

Engage the 2 claws to install the 2 assist grip plugs.

B193061


Hide 62412 30.INSTALL CENTER PILLAR GARNISH LH

HINT:

Use the same procedure for both sides.


Hide 62413A 31.INSTALL LOWER CENTER PILLAR GARNISH RH

B190125

a.

Engage the 7 clips and 2 claws to install the center pillar garnish.


b.
B190129

Install the front seat outer belt assembly RH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.
B190128

Engage the 3 claws to install the cover.


Hide 62414A 32.INSTALL LOWER CENTER PILLAR GARNISH LH

HINT:

Use the same procedure for both sides.


Hide 62211 33.INSTALL FRONT PILLAR GARNISH RH

B190132E02
1.99,1.24 1.688,1.229 false 1.375,0.156 2.125,0.375 false 1.281,0.573 1.646,0.594 false 0.375,0.49 1.333,0.667 0.958,0.177 10 false Adhesive Tape 0.375,0.063 1.427,0.229 1.052,0.167 10 false Protective cover 2.01,1.156 3.094,1.583 1.083,0.427 10 true Curtain Shield Airbag Assembly

a.

Remove the protective cover.


b.

Engage the claw to install the front pillar garnish.


c.

Install the assist grip with the 2 bolts.

Torque:
9.7 N*m (99 kgf*cm, 86 in.*lbf)


d.

Engage the 2 claws to install the 2 assist grip plugs.

B193062


Hide 62212 34.INSTALL FRONT PILLAR GARNISH LH

HINT:

Use the same procedure for both sides.


Hide 62331C 35.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

B443511E01
1.031,0.917 1.271,0.49 false 2.458,1 2.458,1.271 false 1.313,0.396 2.844,0.594 1.531,0.198 10 false Paint Mark 2.063,1.281 2.958,1.458 0.896,0.177 10 false Location Mark

a.

Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.

Paint Mark
Area Color
RH side Pink
LH side Purple


Hide 62332C 36.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Use the same procedure for both sides.


Hide 67917C 37.INSTALL REAR DOOR SCUFF PLATE RH

B186666

a.

Engage the 2 claws and 5 clips to install the rear door scuff plate.


b.

Install the 2 bolts.


c.
B186665

Engage the 6 claws, 5 clips and 2 guides to install the rear door scuff plate.


d.

Install the screw.


Hide 67918D 38.INSTALL REAR DOOR SCUFF PLATE LH

HINT:

Use the same procedure for both sides.


Hide 51775 39.INSTALL REAR FLOOR STEP NO. 1 COVER

B191404

a.

Engage the 2 claws to install the rear floor step No. 1 cover.


Hide 40.INSTALL REAR FLOOR STEP NO. 2 COVER

B193890

a.

Engage the 2 claws to install the rear floor step No. 2 cover.


Hide 71693 41.INSTALL REAR SEAT CUSHION HINGE LOWER COVER RH

B191794

a.

Engage the 2 clips and 5 claws to install the rear cushion hinge lower cover RH.


Hide 71694 42.INSTALL REAR SEAT CUSHION HINGE LOWER COVER LH

HINT:

Use the same procedure for both sides.


Hide 62311B 43.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

B190153E02
1.479,0.271 1.031,0.917 false 2.458,1.01 2.458,1.365 false 1.51,0.188 2.198,0.354 0.688,0.167 10 false Paint Mark 2.083,1.365 3,1.531 0.917,0.167 10 false Location Mark

a.

Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.

Paint Mark
Area Color
RH side White
LH side Yellow


Hide 62312B 44.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Use the same procedure for both sides.


Hide 62111C 45.INSTALL COWL SIDE TRIM BOARD RH

B190152

a.

Engage the 2 clips to install the cowl side trim board.


b.

Install the clip.


Hide 62112 46.INSTALL COWL SIDE TRIM BOARD LH

HINT:

Use the same procedure for both sides.


Hide 67913B 47.INSTALL FRONT DOOR SCUFF PLATE RH

B190151

a.

Engage the 9 claws to install the scuff plate.


Hide 67914B 48.INSTALL FRONT DOOR SCUFF PLATE LH

HINT:

Use the same procedure for both sides.


Hide 49.INSTALL REAR NO. 2 SEAT ASSEMBLY RH

a.

for Manual Seat:

Install the rear No. 2 seat assembly RH (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Manual Seat Type RH Side)>INSTALLATION).


b.

for Power Seat:

Install the rear No. 2 seat assembly RH (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Power Seat Type RH Side)>INSTALLATION).


Hide 50.INSTALL REAR NO. 2 SEAT ASSEMBLY LH

a.

for Manual Seat:

Install the rear No. 2 seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Manual Seat Type LH Side)>INSTALLATION).


b.

for Power Seat:

Install the rear No. 2 seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Power Seat Type LH Side)>INSTALLATION).


Hide 58417F 51.INSTALL DECK BOARD BRACKET

B190119

a.

Install the deck board bracket with the 2 bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 58403K 52.INSTALL DECK BOARD REINFORCEMENT SUB-ASSEMBLY

B190120

a.

Install the deck board reinforcement with the 4 bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 58401A 53.INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY

B190117

a.

Engage the 5 clips to install the No. 1 deck board.


Hide 66310D 54.INSTALL ROPE HOOK ASSEMBLY

B191405

a.

Install the rope hook with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

HINT:

Use the same procedure for both sides.



Hide 64429G 55.INSTALL LUGGAGE COMPARTMENT TRIM BOX

B190116

a.

Install the luggage compartment trim box with the 4 bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


b.
B194633

Install the 4 caps.


Hide 58408D 56.INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY

B194608

a.

Engage the 4 guides to install the No. 2 deck board.


Hide 57.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 58.CHECK SRS WARNING LIGHT