Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS
RM27L0U _59 Vehicle Exterior _049347 WINDOW / GLASS _0235948 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


PROCEDURE

Hide 56111 1.CLEAN WINDSHIELD GLASS

B073128

a.

Using a scraper, remove the damaged stoppers, dam and adhesive from the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.



b.

Clean the outer edge of the windshield glass with a non-residue solvent.

NOTICE:
·

Do not touch the windshield glass surface after cleaning it.

·

Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.




Hide 2.CLEAN VEHICLE BODY

a.
B073084E27
1.198,1.667 1.542,1.802 1.542,1.802 2.01,1.719 false 2.198,1.458 2.198,0.125 2.198,0.125 2.313,0.125 false 0.417,1.573 0.417,0.115 0.417,0.115 0.594,0.115 false 1.052,1.813 1.906,1.99 0.854,0.177 10 false Vehicle Body 0.646,0.031 1.25,0.188 0.604,0.156 10 false Adhesive 2.365,0.042 2.969,0.198 0.604,0.156 10 false Adhesive

Clean and shape the contact surface of the vehicle body.

i.

Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

NOTICE:

Do not damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surface of the vehicle body with a shop rag or piece of cloth saturated with cleaner.

HINT:

Clean the vehicle body even if all the adhesive has been removed.




Hide 56116C 3.INSTALL NO. 2 WINDSHIELD GLASS STOPPER

a.

Using a brush or sponge, coat the application area of the No. 2 stoppers with Primer G.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.



HINT:

If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



b.

Install 2 new No. 2 stoppers onto the windshield glass, as shown in the illustration.

B443163E01
1.01,0.573 1.271,1.438 false 1.76,0.552 1.635,1.385 false 5.115,0.5 5.385,1.375 false 6.052,0.542 5.875,1.438 false 1.948,1.427 1.948,2.302 false 5.188,1.438 5.188,2.313 false 0.188,0.073 0.854,0.271 0.667,0.198 10 false Backside: 0.083,0.469 1.01,0.667 0.927,0.198 10 false Ceramic Notch 1.792,0.396 2.885,0.583 1.094,0.188 10 false Windshield Glass 1.24,1.76 1.677,1.969 0.438,0.208 10 false Center 4.167,0.302 5.26,0.49 1.094,0.188 10 false Windshield Glass 6.083,0.417 7.042,0.604 0.958,0.188 10 false Ceramic Notch 5.552,1.76 5.99,1.969 0.438,0.208 10 false Center 1.688,2.323 2.5,2.51 0.813,0.188 10 false Ceramic Line 4.75,2.354 5.563,2.542 0.813,0.188 10 false Ceramic Line

HINT:

Only 2-piece type No. 2 stoppers are supplied. Use the 2-piece type stoppers even if a 1-piece type was used.



Hide 56115A 4.INSTALL NO. 1 WINDSHIELD GLASS STOPPER

B442897E01
0.875,0.51 0.875,0.281 0.875,0.281 1.25,0.281 false 2.635,1.74 2.635,1.01 2.635,1.01 2.458,1.01 false 1.271,0.188 1.823,0.375 0.552,0.188 10 false Stopper 2.333,1.781 3.198,1.969 0.865,0.188 10 false Vehicle Body

a.

Install 2 new No. 1 stoppers to the vehicle body, as shown in the illustration.

HINT:

Only 2-piece type No. 1 stoppers are supplied. Use the 2-piece type stoppers even if a 1-piece type was used.



Hide 56117D 5.INSTALL WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the application area of adhesive dam with Primer G.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.



HINT:

If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



b.

Install a new adhesive dam onto the windshield glass, as shown in the illustration.

U151921E02
0.719,2.167 0.958,2.385 0.958,2.385 0.958,2.948 false 4.802,2.208 4.594,2.375 4.594,2.375 4.594,2.948 false 5.906,2.875 5.969,3.094 5.969,3.094 6.031,2.875 false 6.427,1.188 6.49,1.396 6.49,1.396 6.552,1.188 false 2.469,2.865 2.469,3.313 false 0.031,0 0.948,0.167 0.917,0.167 10 false Backside: 1.792,2.229 1.948,2.417 0.156,0.188 10 false A 1.438,2.167 1.594,2.354 0.156,0.188 10 false A 3.979,2.031 4.135,2.219 0.156,0.188 10 false A 3.625,2.094 3.781,2.281 0.156,0.188 10 false A 2.99,2.583 3.156,2.781 0.167,0.198 10 false B 3,2.979 3.167,3.167 0.167,0.188 10 false B 0.302,2.958 1.677,3.125 1.375,0.167 10 false Dam Reference Line 4.01,2.938 5.333,3.104 1.323,0.167 10 false Dam Reference Line 1.979,3.302 3.302,3.469 1.323,0.167 10 false Dam Reference Line 5.677,1.406 6.958,1.573 1.281,0.167 10 false Dam Reference Line 4.063,0.594 5.052,0.771 0.99,0.177 10 false Ceramic Notch 0.583,0.615 1.531,0.802 0.948,0.188 10 false Ceramic Notch 5.604,3.115 6.917,3.292 1.313,0.177 10 false Dam Reference Line 5.604,2.031 5.969,2.208 0.365,0.177 10 false B - B 5.625,0.333 6.167,0.542 0.542,0.208 10 false A - A 5.156,1.604 5.344,1.813 0.188,0.208 10 false a 0.302,1.542 0.49,1.75 0.188,0.208 10 false a

Standard Dimension:
Area Dimension
a 29.2 mm (0.417 in.)


NOTICE:

Install the new adhesive dam along the ceramic notches.



Hide 6.INSTALL WINDSHIELD OUTSIDE UPPER MOULDING

a.
B166397E04
1.49,3.021 1.719,2.885 false 2.552,2.438 2.292,2.927 false 0.073,0.021 0.948,0.24 0.875,0.219 10 false Backside: 1.021,2.938 1.458,3.125 0.438,0.188 10 false Primer 2.594,2.333 3.229,2.542 0.635,0.208 10 false Moulding

Using a brush or sponge, coat the edge of the glass and the contact surface with Primer G.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Install the windshield outside upper moulding, as shown in the illustration.

NOTICE:

Do not drive the vehicle for the amount of time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



Hide 56111 7.INSTALL WINDSHIELD GLASS

B194333E01
2.216,0.014 2.935,0.165 0.719,0.151 10 Matchmark 1.806,0.431 2.193,0.102 2.193,0.102 1.81,0.804 false

a.

Position the windshield glass.

i.

Using suction cups, place the windshield glass in the correct position.


ii.

Check that the whole contact surface of the windshield glass rim is perfectly even.


iii.

Align the matchmarks on the windshield glass and vehicle body.

NOTICE:

Check that the windshield glass stoppers are attached to the vehicle body correctly.




b.
B106027E10
2.417,1.031 2.125,0.729 false 2.417,2.042 2.021,1.802 false 2.5,2.073 2.573,2.219 false 1.573,0.031 2.573,0.25 1,0.219 10 false CORRECT 1.375,0.563 2.25,0.792 0.875,0.229 10 false Primer M 1.417,1.708 2.021,1.885 0.604,0.177 10 false Primer M 2.573,2.188 3.417,2.385 0.844,0.198 10 false Adhesive 1.24,2.271 2.375,2.5 1.135,0.229 10 false INCORRECT 0.656,4.323 1.25,4.5 0.594,0.177 10 false Primer M

Using a brush, coat the installation surface on the vehicle body with Primer M.

NOTICE:
·

Do not coat the adhesive with Primer M.

·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.



HINT:

If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries



c.

Using a brush or sponge, coat the application areas that still have adhesive attached with Primer G.

B194335E02
4.281,1.563 4.281,1.948 false 5.865,1.563 5.865,1.948 false 4.208,3.646 4.208,4.01 false 5.938,3.646 5.938,4.021 false 6.125,3.646 6.125,3.875 6.125,3.875 5.948,3.875 false 0.979,3.01 0.906,3.323 false 3.802,1.958 4.875,2.271 1.073,0.313 10 false Adhesive Center Line 5.49,1.958 6.563,2.271 1.073,0.313 10 false Adhesive Center Line 3.802,4.042 4.875,4.354 1.073,0.313 10 false Adhesive Center Line 5.49,4.042 6.563,4.354 1.073,0.313 10 false Adhesive Center Line 3.698,0.99 3.948,1.135 0.25,0.146 10 false A-A 5.396,0.99 5.646,1.135 0.25,0.146 10 false B-B 3.698,3.031 3.979,3.177 0.281,0.146 10 false C-C 5.396,3.031 5.656,3.177 0.26,0.146 10 false D-D 1.396,1.677 1.51,1.823 0.115,0.146 10 false A 1.354,2.021 1.469,2.167 0.115,0.146 10 false A 2.656,1.635 2.771,1.781 0.115,0.146 10 false A 2.688,1.99 2.802,2.135 0.115,0.146 10 false A 2.021,1.667 2.135,1.813 0.115,0.146 10 false B 2.021,2.01 2.135,2.156 0.115,0.146 10 true B 3.073,2.365 3.188,2.51 0.115,0.146 10 false C 2.729,2.448 2.844,2.594 0.115,0.146 10 false C 2.031,2.833 2.146,2.979 0.115,0.146 10 false D 2.031,3.188 2.146,3.333 0.115,0.146 10 false D 0.375,3.333 1.458,3.656 1.083,0.323 10 false Adhesive Center Line 0.719,4.49 1.292,4.635 0.573,0.146 10 false Primer G 0.073,0.073 0.917,0.271 0.844,0.198 12 false Back Side:

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.



HINT:
·

Apply primer G onto the ceramic notches.

·

If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.




d.

Apply adhesive to the glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.
B106205E01
2.361,0.73 3.162,1.125 0.802,0.395 10 8.0 mm (0.315 in.) 0.968,1.848 2.110,2.024 1.142,0.177 10 12 mm (0.472 in.)

Cut off the tip of the cartridge nozzle, as shown in the illustration.

HINT:

After cutting off the tip, use all adhesive within the time limit described in the table below.


Usage Time Frame:
Temperature Tack-free Time
35°C (95°F) 15 minutes
20°C (68°F) 1 hour and 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with a cartridge.


iii.

Apply adhesive to the windshield glass, as shown in the illustration.

B194336E03
4.448,1.563 4.615,1.927 false 6.052,1.563 6.229,1.927 false 6.115,3.646 6.25,4.094 6.25,4.094 6.323,3.646 false 4.385,3.646 4.604,4.094 false 2.104,1.656 2.229,1.802 0.125,0.146 10 false A 2.063,2.01 2.188,2.156 0.125,0.146 10 false A 3.365,1.625 3.49,1.771 0.125,0.146 10 false A 3.385,1.979 3.51,2.125 0.125,0.146 10 false A 2.719,1.656 2.844,1.802 0.125,0.146 10 false B 2.74,2.01 2.865,2.156 0.125,0.146 10 true B 3.771,2.365 3.896,2.51 0.125,0.146 10 false C 3.427,2.438 3.552,2.583 0.125,0.146 10 false C 2.729,2.823 2.854,2.969 0.125,0.146 10 false D 2.729,3.177 2.854,3.323 0.125,0.146 10 false D 0.323,4.229 0.427,4.396 0.104,0.167 10 false a 0.75,3.792 0.854,3.958 0.104,0.167 10 false b 4.417,3.042 4.521,3.208 0.104,0.167 10 false c 5.823,3.094 5.927,3.26 0.104,0.167 10 false c 6.375,2.854 6.479,3.021 0.104,0.167 10 false b 6.094,0.979 6.198,1.146 0.104,0.167 10 false c 4.5,0.979 4.604,1.146 0.104,0.167 10 false c 4.094,1.948 5.167,2.26 1.073,0.313 10 false Adhesive Center Line 5.74,1.948 6.813,2.26 1.073,0.313 10 false Adhesive Center Line 4.094,4.125 5.167,4.438 1.073,0.313 10 false Adhesive Center Line 5.74,4.125 6.813,4.438 1.073,0.313 10 false Adhesive Center Line 4.063,0.708 4.333,0.854 0.271,0.146 10 false A-A 5.646,0.74 5.917,0.885 0.271,0.146 10 false B-B 4.063,2.698 4.333,2.844 0.271,0.146 10 false C-C 5.646,2.698 5.917,2.844 0.271,0.146 10 false D-D 1,4.313 1.688,4.469 0.688,0.156 10 false : Adhesive 0.052,0.042 0.885,0.229 0.833,0.188 10 false Back Side: 0.865,2.188 1,2.385 0.135,0.198 10 true a 0.313,2.094 0.458,2.25 0.146,0.156 10 true b

Standard Dimension:
Area Dimension
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)
c 4.0 mm (0.157 in.)




e.
B194333E01
2.216,0.014 2.935,0.165 0.719,0.151 10 Matchmark 1.806,0.431 2.193,0.102 2.193,0.102 1.81,0.804 false

Install the windshield glass.

i.

Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the windshield glass stoppers are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and windshield glass.




ii.

Lightly press the front surface of the windshield glass to ensure a close fit.


iii.
B149738E01
2.514,0.142 3.230,0.294 0.716,0.151 10 Windshield 2.731,1.471 3.062,1.629 0.332,0.158 10 Dam 1.924,1.708 2.532,1.859 0.608,0.151 10 Adhesive 2.491,0.22 2.394,0.22 2.394,0.22 2.584,0.855 false 2.921,1.156 2.921,1.471 false 2.288,1.705 2.288,1.614 2.288,1.614 2.415,1.287 false 0.709,0.137 1.426,0.288 0.716,0.151 10 Windshield 0.926,1.466 1.258,1.623 0.332,0.158 10 Dam 0.12,1.702 0.727,1.853 0.608,0.151 10 Adhesive 0.687,0.215 0.589,0.215 0.589,0.215 0.779,0.849 false 1.116,1.15 1.116,1.466 false 0.483,1.7 0.483,1.608 0.483,1.608 0.588,1.344 false

If necessary, use a scraper to correct the level or position of adhesive that has been applied.

HINT:

Apply adhesive onto the windshield glass rim.



iv.

Hold the windshield glass using protective tape until applied adhesive hardens.

NOTICE:

Do not drive the vehicle within the time limits described in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour and 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




Hide 75533E 8.INSTALL WINDSHIELD OUTSIDE MOULDING

a.

Using a brush or sponge, coat the application area of the moulding with Primer G.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.



HINT:

If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



b.
B194337E01
0.04,0 0.859,0.184 0.818,0.184 10 Back Side: 0.217,1.9 1.196,2.137 0.978,0.236 12 w/o Rain G: 0.217,3.202 1.106,3.419 0.889,0.217 12 w/ Rain G: 1.564,2.908 1.697,3.087 0.133,0.180 10 a 1.582,4.328 1.715,4.508 0.133,0.180 10 a

Install a new moulding onto the windshield glass, as shown in the illustration.


c.

Apply Primer G to the windshield outside moulding area "a" shown in the illustration.


Hide 9. CHECK FOR LEAKAGE AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 87810 10.INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

Hide 87810 11.INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)

Hide 12.INSTALL ROOF HEADLINING ASSEMBLY

HINT:

Return the front section of the roof headlining assembly to the original position.


Hide 74310 15.INSTALL VISOR ASSEMBLY RH (w/ Illumination)

Hide 74320 16.INSTALL VISOR ASSEMBLY LH (w/ Illumination)

HINT:

Use the same procedure as for the RH side.


Hide 74310 17.INSTALL VISOR ASSEMBLY RH (w/o Illumination)

Hide 74320 18.INSTALL VISOR ASSEMBLY LH (w/o Illumination)

HINT:

Use the same procedure as for the RH side.


Hide 74318 20.INSTALL VISOR BRACKET COVER LH

HINT:

Use the same procedure as for the RH side.


Hide 81240 22.INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/ Rear Seat Entertainment System)

Hide 63650A 23.INSTALL ROOF CONSOLE BOX ASSEMBLY

Hide 62212 25.INSTALL FRONT PILLAR GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 62311B 26.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 62312B 27.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Use the same procedure as for the RH side.


Hide 62112 29.INSTALL COWL SIDE TRIM BOARD LH

HINT:

Use the same procedure as for the RH side.


Hide 67914 31.INSTALL FRONT DOOR SCUFF PLATE LH

HINT:

Use the same procedure as for the RH side.


Hide 55781E 32.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53866J 33.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

Hide 53867H 34.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

Hide 85211B 35.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 85221B 36.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 37.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 38.INSPECT SRS WARNING LIGHT