Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS
RM27L0U _59 Vehicle Exterior _049347 WINDOW / GLASS _0235948 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 85211B 3.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 85221B 4.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 53866J 5.REMOVE FRONT FENDER TO COWL SIDE SEAL RH

Hide 53867H 6.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

Hide 55781E 7.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 67913 8.REMOVE FRONT DOOR SCUFF PLATE RH

Hide 67914 9.REMOVE FRONT DOOR SCUFF PLATE LH

HINT:

Use the same procedure as for the RH side.


Hide 62111C 10.REMOVE COWL SIDE TRIM BOARD RH

Hide 62112 11.REMOVE COWL SIDE TRIM BOARD LH

HINT:

Use the same procedure as for the RH side.


Hide 62311B 12.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 62312B 13.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Use the same procedure as for the RH side.


Hide 62211 14.REMOVE FRONT PILLAR GARNISH RH

Hide 62212 15.REMOVE FRONT PILLAR GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 63650A 16.REMOVE ROOF CONSOLE BOX ASSEMBLY

Hide 81240 17.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 81240 18.REMOVE NO. 1 ROOM LIGHT ASSEMBLY (w/ Rear Seat Entertainment System)

Hide 74318 20.REMOVE VISOR BRACKET COVER LH

HINT:

Use the same procedure as for the RH side.


Hide 74310 21.REMOVE VISOR ASSEMBLY RH (w/o Illumination)

Hide 74320 22.REMOVE VISOR ASSEMBLY LH (w/o Illumination)

HINT:

Use the same procedure as for the RH side.


Hide 74310 23.REMOVE VISOR ASSEMBLY RH (w/ Illumination)

Hide 74320 24.REMOVE VISOR ASSEMBLY LH (w/ Illumination)

HINT:

Use the same procedure as for the RH side.


Hide 74610A 25.REMOVE ASSIST GRIP SUB-ASSEMBLY

Hide 63310 27.REMOVE ROOF HEADLINING ASSEMBLY

HINT:

It is not necessary to remove the roof headlining completely. Slightly lower the front section of the roof headlining.


Hide 87810 28.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

Hide 87810 29.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)

Hide 75533E 30.REMOVE WINDSHIELD OUTSIDE MOULDING

B194338E01
0.095,0.104 1.088,0.307 0.993,0.202 12 w/o Rain G: 0.095,2.212 0.954,2.415 0.860,0.202 12 w/ Rain G: 2.061,0.813 2.314,0.969 0.253,0.156 10 Cut 1.681,1.074 2.034,0.909 false 2.065,2.623 2.318,2.779 0.253,0.156 10 Cut 1.685,2.884 2.038,2.719 false

a.

Using a knife, cut off the windshield outside moulding, as shown in the illustration.

NOTICE:

Do not damage the vehicle body with the knife.



b.

Remove the windshield outside moulding.

HINT:

Make a partial cut in the windshield outside moulding. Then pull and remove it by hand.



Hide 31.REMOVE WINDSHIELD OUTSIDE UPPER MOULDING

a.
B166393E02
1.236,0.389 1.491,0.590 0.255,0.201 10 Cut 1.806,0.745 1.536,0.512 false

Using a knife, cut off the windshield outside upper moulding as shown in the illustration.

NOTICE:

Do not damage the vehicle body with the knife.



b.

Remove the windshield outside upper moulding.

HINT:

Make a partial cut in the windshield outside upper moulding. Then pull and remove it by hand.



Hide 56111 32.REMOVE WINDSHIELD GLASS

a.
B191738E02
2.052,0.167 1.729,0.479 false 2.073,0.083 3.115,0.406 1.042,0.323 10 true Protective Tape

Apply protective tape to the installation area on the windshield glass on the vehicle body.

HINT:

Apply protective tape to the installation surface to prevent it from being scratched.



b.

Pass a piano wire between the vehicle body and glass from the interior.

B443162E01
1.385,1.281 0.781,0.76 false 1.719,0.708 1.552,0.396 false 2.646,2.271 2.385,1.698 false 6.042,0.99 4.573,0.198 4.573,0.198 4.948,0.979 true 5.229,2.302 5.115,2.094 false 0.615,0.156 1.542,0.344 0.927,0.188 10 false Wooden Block 0.302,0.625 0.75,0.99 0.448,0.365 10 false Plastic Sheet 2.302,2.313 3.26,2.521 0.958,0.208 10 false Protective Tape 4,0.083 4.552,0.292 0.552,0.208 10 false Stopper 5.271,2.24 6,2.427 0.729,0.188 10 false Piano Wire


c.

Tie both wire ends to wooden blocks or similar objects.


d.

Cut off the adhesive by pulling the piano wire around the windshield glass.

NOTICE:
·

When separating the windshield glass, take care not to damage the paint or the interior and exterior ornaments.

·

To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.




e.
B194333E01
2.216,0.014 2.935,0.165 0.719,0.151 10 Matchmark 1.806,0.431 2.193,0.102 2.193,0.102 1.81,0.804 false

Place matchmarks on the windshield glass and vehicle body on the locations indicated in the illustration.

HINT:

Matchmarks do not need to be placed if the windshield glass is not going to be reused.



f.

Disconnect the stoppers.

B191737E01
1.325,0.018 2.333,0.217 1.008,0.200 12 1-piece type: 4.863,0.018 5.871,0.217 1.008,0.200 12 2-piece type: 0.896,0.841 1.254,0.996 0.358,0.155 10 No. 2 4.329,0.48 4.687,0.635 0.358,0.155 10 No. 2 4.438,0.951 4.795,1.106 0.358,0.155 10 No. 1 1.399,0.816 1.253,0.896 false 4.954,0.993 4.789,1.022 false 4.934,0.776 4.692,0.552 false

NOTICE:
·

There are No. 1 and No. 2 stoppers on the windshield glass, as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.

·

To prevent the windshield glass from dropping when performing this operation, be sure to hold the windshield glass using suction cups.



HINT:

Depending on vehicles, a 1-piece or 2-piece type stopper is used.



g.

Using suction cups, remove the windshield glass.

NOTICE:
·

Be careful not to drop the windshield glass.

·

Leave as much adhesive on the vehicle body as possible when removing the windshield glass.




Hide 56117E 33.REMOVE WINDOW GLASS ADHESIVE DAM

a.

Using a scraper, remove the adhesive dam.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the adhesive dam with a new one.




Hide 56116C 34.REMOVE NO. 2 WINDSHIELD GLASS STOPPER

a.

Using a scraper, remove the 2 No. 2 stoppers.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the No. 2 stoppers with new ones.




Hide 56115A 35.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

B194334

a.

Remove the 2 No. 1 stoppers.

NOTICE:

Be sure to replace the No. 1 stoppers with new ones.