Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM
RM27L0U _59 Vehicle Exterior _049348 SLIDING ROOF / CONVERTIBLE _0235952 SLIDING ROOF SYSTEM C

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  B2342  Switch Failure  


DESCRIPTION

This DTC is stored when the sliding roof drive gear (sliding roof ECU) detects that the SLIDE or TILT switch in the roof console box (sliding roof switch) is stuck for 30 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2342 Sliding roof drive gear (sliding roof ECU) detects that SLIDE or TILT switch in roof console box is stuck for 30 seconds or more.
·

Sliding roof switch

·

Roof console box

·

Harness and connector

·

Sliding roof drive gear (Sliding roof ECU)



WIRING DIAGRAM

B167040E04
5.392,2.925 5.706,3.104 0.313,0.179 10 U3 2.445,2.475 2.566,2.631 0.121,0.156 10 E 1.827,2.475 1.997,2.631 0.170,0.156 10 E 2.663,1.944 2.869,2.132 0.207,0.188 10 3 2.013,1.944 2.220,2.132 0.207,0.188 10 3 2.017,2.475 2.224,2.663 0.207,0.188 10 5 2.268,1.944 2.565,2.100 0.297,0.156 10 CLS 1.333,2.153 1.717,2.309 0.384,0.156 10 Close 2.24,1.458 2.564,1.614 0.325,0.156 10 OPN 1.19,1.539 1.584,1.737 0.394,0.198 10 Open 2.149,0.961 2.620,1.117 0.471,0.156 10 DOWN 1.407,1.196 1.780,1.352 0.373,0.156 10 Down 0.994,0.979 1.367,1.135 0.373,0.156 10 TILT 0.937,1.967 1.367,2.122 0.429,0.156 10 SLIDE 5.723,0.611 6.351,0.766 0.628,0.156 10 UP 5.723,2.045 6.351,2.201 0.628,0.156 10 CLS 5.723,1.555 6.351,1.710 0.628,0.156 10 OPN 5.723,1.057 6.351,1.213 0.628,0.156 10 DWN 2.341,0.528 2.565,0.684 0.224,0.156 10 UP 1.33,0.525 1.557,0.681 0.228,0.156 10 Up 5.514,1.458 5.666,1.646 0.153,0.188 10 6 5.514,0.961 5.666,1.149 0.153,0.188 10 2 2.023,0.961 2.176,1.149 0.153,0.188 10 2 5.514,0.528 5.666,0.716 0.153,0.188 10 1 2.004,0.528 2.157,0.716 0.153,0.188 10 1 5.514,1.944 5.666,2.132 0.153,0.188 10 7 2.663,1.458 2.869,1.646 0.207,0.188 10 4 2.013,1.458 2.220,1.646 0.207,0.188 10 4 2.663,0.961 2.869,1.149 0.207,0.188 10 5 2.663,0.528 2.869,0.716 0.207,0.188 10 6 2.663,2.475 2.869,2.663 0.207,0.188 10 7 0.412,3.291 0.706,3.447 0.295,0.156 10 U7 0.412,3.454 2.114,3.610 1.702,0.156 10 Roof Console Box 0.663,2.927 1.921,3.111 1.258,0.184 10 Sliding Roof Switch 5.392,3.101 6.875,3.541 1.482,0.440 10 Sliding Roof Drive Gear (Sliding Roof ECU)

PROCEDURE

1.CHECK DTC

b.

Check for DTCs (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2342 is output A
No DTC is output B



A

2.READ VALUE USING TECHSTREAM (SWITCH STATUS)

B

2.READ VALUE USING TECHSTREAM (SWITCH STATUS)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Body Electrical / Sliding Roof / Data List.


e.

According to the display on the Techstream, read the Data List.

Sliding Roof
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Open Switch Failure (Past) Open switch failure signal (Past)/Fail or Not Fail Fail: Sliding roof tilt open signal failure (Past)
Not Fail: Sliding roof tilt open signal not fail (Past)
-
Close Switch Failure (Past) Close switch failure signal (Past)/Fail or Not Fail Fail: Sliding roof tilt close signal failure (Past)
Not Fail: Sliding roof tilt close signal not fail (Past)
-
Up Switch Failure (Past) Up switch failure signal (Past)/Fail or Not Fail Fail: Sliding roof tilt up signal failure (Past)
Not Fail: Sliding roof tilt up signal not fail (Past)
-
Down Switch Failure (Past) Down switch failure signal (Past)/Fail or Not Fail Fail: Sliding roof tilt down signal failure (Past)
Not Fail: Sliding roof tilt down signal not fail (Past)
-
Open Switch Failure (Current) Open switch failure signal (Current)/Fail or Not Fail Fail: Sliding roof tilt open signal failure (Current)
Not Fail: Sliding roof tilt open signal not fail (Current)
-
Close Switch Failure (Current) Close switch failure signal (Current)/Fail or Not Fail Fail: Sliding roof tilt close signal failure (Current)
Not Fail: Sliding roof tilt close signal not fail (Current)
-
Up Switch Failure (Current) Up switch failure signal (Current)/Fail or Not Fail Fail: Sliding roof tilt up signal failure (Current)
Not Fail: Sliding roof tilt up signal not fail (Current)
-
Down Switch Failure (Current) Down switch failure signal (Current)/Fail or Not Fail Fail: Sliding roof tilt down signal failure (Current)
Not Fail: Sliding roof tilt down signal not fail (Current)
-

OK:

The Techstream displays as shown in the table according to the operation of each switch.




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

3.INSPECT SLIDING ROOF SWITCH
3.INSPECT SLIDING ROOF SWITCH
a.
B167041E05
0.059,2.254 2.530,2.586 2.471,0.332 10 Component without harness connected: (Sliding Roof Switch) 1.155,3.715 0.64,4.07 false 1.424,3.715 0.953,4.252 false 2.022,3.715 2.34,4.317 false 2.301,3.715 2.779,4.089 false 1.686,3.715 1.498,4.328 false 2.78,4.044 3.019,4.184 0.239,0.140 10 UP 2.104,4.317 2.723,4.454 0.619,0.137 10 DOWN 1.265,4.328 1.784,4.519 0.519,0.191 10 CLS 0.672,4.245 1.101,4.399 0.429,0.154 10 OPN 0.494,3.996 0.854,4.149 0.360,0.154 10 E

Remove the sliding roof switch (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (UP) - 5 (E) TILT switch is pressed to up Below 1 Ω
TILT switch is not pressed to up 10 kΩ or higher
2 (DOWN) - 5 (E) TILT switch is pressed to down Below 1 Ω
TILT switch is not pressed to down 10 kΩ or higher
3 (CLS) - 5 (E) SLIDE switch is pressed to close Below 1 Ω
SLIDE switch is not pressed to close 10 kΩ or higher
4 (OPN) - 5 (E) SLIDE switch is pressed to open Below 1 Ω
SLIDE switch is not pressed to open 10 kΩ or higher




OK

4.INSPECT ROOF CONSOLE BOX ASSEMBLY

NG

4.INSPECT ROOF CONSOLE BOX ASSEMBLY
a.

Remove the roof console box with sliding roof switch (See page Vehicle Interior>INTERIOR PANELS / TRIM>OVERHEAD CONSOLE BOX>REMOVAL).


E146741E03
0.054,0.007 2.592,0.350 2.538,0.343 10 Component without harness connected: (Roof Console Box) 0.342,2.706 0.575,2.882 0.232,0.177 10 UP 0.405,2.104 0.540,2.260 0.135,0.156 10 E 2.875,2.68 3.204,2.849 0.330,0.170 10 CLS 2.868,1.915 3.198,2.085 0.330,0.170 10 OPN 2.377,1.313 2.883,1.468 0.506,0.155 10 DOWN 1.115,2.317 0.573,2.196 false 1.347,2.549 0.609,2.792 false 1.738,2.317 2.824,2.013 false 1.938,2.549 2.833,2.772 false 1.538,2.319 2.343,1.409 false

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (CLS) - 7 (E) SLIDE switch is pressed to close Below 1 Ω
SLIDE switch is not pressed to close 10 kΩ or higher
4 (OPN) - 7 (E) SLIDE switch is pressed to open Below 1 Ω
SLIDE switch is not pressed to open 10 kΩ or higher
5 (DOWN) - 7 (E) TILT switch is pressed to down Below 1 Ω
TILT switch is not pressed to down 10 kΩ or higher
6 (UP) - 7 (E) TILT switch is pressed to up Below 1 Ω
TILT switch is not pressed to up 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (ROOF CONSOLE BOX - SLIDING ROOF ECU AND BODY GROUND)

NG

REPLACE ROOF CONSOLE BOX ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ROOF CONSOLE BOX - SLIDING ROOF ECU AND BODY GROUND)
U153201E02
0.823,1.573 1.146,1.24 false 2.177,3.656 2.635,3.365 false 1.073,1.875 1.375,1.323 false 2.271,4.354 1.99,3.771 false 1.563,2.021 1.438,1.563 false 0.708,4.104 1.552,3.781 false 1.656,4.354 1.75,3.781 false 3.083,3.625 2.354,3.76 false 1.948,1.865 1.656,1.563 false 0.073,0.073 2.313,0.406 2.24,0.333 10 false Front view of wire harness connector: (to Sliding Roof ECU) 0.115,2.344 2.385,2.698 2.271,0.354 10 false Front view of wire harness connector: (to Roof Console Box) 0.417,1.229 0.615,1.396 0.198,0.167 10 false U3 1.406,2.021 1.854,2.188 0.448,0.167 10 false OPN 1.51,4.375 1.948,4.542 0.438,0.167 10 false OPN 0.677,1.594 0.906,1.76 0.229,0.167 10 false UP 2.667,3.281 2.896,3.448 0.229,0.167 10 false UP 3.125,3.542 3.302,3.708 0.177,0.167 10 false E 0.792,1.875 1.281,2.042 0.49,0.167 10 false DWN 2.292,4.323 2.75,4.49 0.458,0.167 10 false DOWN 1.969,1.823 2.479,1.99 0.51,0.167 10 false CLS 0.49,4.115 0.875,4.281 0.385,0.167 10 false CLS 0.438,3.563 0.646,3.729 0.208,0.167 10 false U7

a.

Disconnect the U3 ECU connector.


b.

Disconnect the U7 roof console box connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U7-3 (CLS) - U3-7 (CLS) Always Below 1 Ω
U7-3 (CLS) - Body ground Always 10 kΩ or higher
U7-4 (OPN) - U3-6 (OPN) Always Below 1 Ω
U7-4 (OPN) - Body ground Always 10 kΩ or higher
U7-5 (DOWN) - U3-2 (DWN) Always Below 1 Ω
U7-5 (DOWN) - Body ground Always 10 kΩ or higher
U7-6 (UP) - U3-1 (UP) Always Below 1 Ω
U7-6 (UP) - Body ground Always 10 kΩ or higher
U7-7 (E) - Body ground Always Below 1 Ω




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR