This DTC is stored when the sliding roof drive gear (sliding roof ECU) has not been initialized.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2343 | Sliding roof drive gear (sliding roof ECU) has not been initialized | ·
Sliding roof switch ·
Roof console box ·
Harness and connector ·
Sliding roof drive gear (Sliding roof ECU) |
Check that the sliding roof drive gear can be initialized (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).
Sliding roof drive gear can be initialized.
OK
NG
Clear the DTCs (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| DTC B2343 is output | B |
A
B
Disconnect the U3 ECU connector.
Disconnect the U7 roof console box connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U7-3 (CLS) - U3-7 (CLS) | Always | Below 1 Ω |
| U7-3 (CLS) - Body ground | Always | 10 kΩ or higher |
| U7-4 (OPN) - U3-6 (OPN) | Always | Below 1 Ω |
| U7-4 (OPN) - Body ground | Always | 10 kΩ or higher |
| U7-5 (DOWN) - U3-2 (DWN) | Always | Below 1 Ω |
| U7-5 (DOWN) - Body ground | Always | 10 kΩ or higher |
| U7-6 (UP) - U3-1 (UP) | Always | Below 1 Ω |
| U7-6 (UP) - Body ground | Always | 10 kΩ or higher |
| U7-7 (E) - Body ground | Always | Below 1 Ω |
OK
NG
Remove the sliding roof switch (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 (UP) - 5 (E) | TILT switch is pressed to up | Below 1 Ω |
| TILT switch is not pressed to up | 10 kΩ or higher | |
| 2 (DOWN) - 5 (E) | TILT switch is pressed to down | Below 1 Ω |
| TILT switch is not pressed to down | 10 kΩ or higher | |
| 3 (CLS) - 5 (E) | SLIDE switch is pressed to close | Below 1 Ω |
| SLIDE switch is not pressed to close | 10 kΩ or higher | |
| 4 (OPN) - 5 (E) | SLIDE switch is pressed to open | Below 1 Ω |
| SLIDE switch is not pressed to open | 10 kΩ or higher |
OK
NG
Remove the roof console box with sliding roof switch (See page Vehicle Interior>INTERIOR PANELS / TRIM>OVERHEAD CONSOLE BOX>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3 (CLS) - 7 (E) | SLIDE switch is pressed to close | Below 1 Ω |
| SLIDE switch is not pressed to close | 10 kΩ or higher | |
| 4 (OPN) - 7 (E) | SLIDE switch is pressed to open | Below 1 Ω |
| SLIDE switch is not pressed to open | 10 kΩ or higher | |
| 5 (DOWN) - 7 (E) | TILT switch is pressed to down | Below 1 Ω |
| TILT switch is not pressed to down | 10 kΩ or higher | |
| 6 (UP) - 7 (E) | TILT switch is pressed to up | Below 1 Ω |
| TILT switch is not pressed to up | 10 kΩ or higher |
OK
NG