Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM27L0U _59 Vehicle Exterior _049349 DOOR / HATCH _0235958 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL CUSHION

a.
B190570

Install the cushion onto the door panel.


Hide 69201A 2.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.
B195034

Slide the front door outside handle frame and engage the claw and install it.


b.

Using "TORX" socket wrench T30, install the front door outside handle frame with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69241H 3.INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD

a.
B190566

Engage the 3 claws and install the front door outside handle front pad.


Hide 69242F 4.INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD

a.
B190565

Engage the 2 claws and install the front door outside handle rear pad.


Hide 69210 5.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B190564

Pushing the front door outside handle assembly in the direction of the arrow mark shown in the illustration, install the front door outside handle assembly.


Hide 69052 7.INSTALL DOOR LOCK CYLINDER (for Driver Side)

a.
B190567

Engage the 2 claws and install the door lock cylinder onto the front door outside handle cover.


Hide 69217E 8.INSTALL FRONT DOOR OUTSIDE HANDLE COVER

a.
B190562

Using "TORX" socket wrench T30, install the front door outside handle cover.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.

Install the hole plug.


Hide 67855B 9.INSTALL FRONT DOOR PANEL PROTECTOR

a.
B190560

Engage the 8 clips and install the front door panel protector.


Hide 67861 10.INSTALL FRONT DOOR WEATHERSTRIP

a.
B190559

Engage the 39 clips and install the front door weatherstrip.


Hide 68610B 11.INSTALL FRONT DOOR CHECK ASSEMBLY

B190558

a.

Apply MP grease to the sliding areas of the door check.


b.

Install the front door check onto the door panel with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the front door check onto the body panel with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 67923 12.INSTALL FRONT NO. 1 DOOR STIFFENER CUSHION

a.
B190557

Engage the 2 clips and install the front No. 1 door stiffener cushion.


Hide 67403F 13.INSTALL FRONT DOOR FRAME REAR LOWER SUB-ASSEMBLY

a.
B190556

Install the front door frame rear lower sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67401F 14.INSTALL FRONT DOOR FRAME FRONT LOWER SUB-ASSEMBLY

a.
B190555

Install the front door frame front lower sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 69801 15.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY

a.

Apply MP grease to the sliding and rotating areas of the front door window regulator.

NOTICE:

Do not apply grease to the window regulator spring.



b.
B190554E02
1.521,0.292 1.667,0.49 0.146,0.198 10 true A

Loosely screw bolt A onto the front door window regulator


c.

Insert the front door window regulator into the door panel. Provisionally tighten bolt A to hang the front door window regulator on the door panel.

NOTICE:

Do not drop the window regulator as it may be damaged.



d.

Install the front door window regulator with the 5 bolts, and tighten bolt A.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the connector.


Hide 68101 16.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.
B192559

Insert the door glass into the door panel by the arrows in the illustration.

NOTICE:

Do not damage the glass.



b.
B190553

Install the front door glass onto the front door window regulator with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68141E 17.INSTALL FRONT DOOR GLASS RUN

a.
B190552

Install the front door glass run.


Hide 67831 18.INSTALL FRONT DOOR SERVICE HOLE COVER

a.
B195024

Apply butyl tape to the door panel, then install a new front door service hole cover as shown in the illustration.

HINT:
·

When installing the service hole cover, pull the links and connectors out through the service hole.

·

There should be no wrinkles or folds after attaching the service hole cover.

·

After attaching the service hole cover, check the quality of the seal.




b.
B190551

Engage the clamps and connect the connectors.


Hide 67625A 19.INSTALL FRONT DOOR NO. 1 TRIM BRACKET

a.
B190549

Install the front door No. 1 trim bracket with the 2 screws.


Hide 89430 20.INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side with Memory)

a.
B192565

Install the outer mirror control ECU assembly with the 2 screws.


b.

Connect the connector.


Hide 68160C 21.INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 87901B 22.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

Hide 68171B 25.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP

a.
B190548

Install the front door glass inner weatherstrip on the front door trim board sub-assembly and fold down the 8 claws, as shown in the illustration.


Hide 69205 26.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B190545

Install the front door inside handle sub-assembly with the 3 screws.


Hide 69277B 27.INSTALL FRONT DOOR INSIDE HANDLE BEZEL

B190544

a.

Install the front door inside handle bezel with the 4 screws.


Hide 84927 28.INSTALL SEAT MEMORY SWITCH (for Driver Side with Memory)

Hide 67601 29.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.

Connect the connectors.


b.
B190543

Connect the front door lock remote control cable and the front door inside locking cable.


c.
B190542

Engage the 10 clips and install the front door trim board sub-assembly.


d.
B190541

Tighten the 2 screws.


e.

Install the front door armrest cover.


Hide 74231 30.INSTALL FRONT ARMREST BASE UPPER PANEL

B190537

a.

Connect the connector.


b.

Engage the 2 clips and 5 claws and install the front armrest base upper panel.


Hide 69283 31.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

a.
B190540

Engage the 4 claws and install the front door inside handle bezel plug


Hide 67491A 32.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

B194240

a.

Engage the 3 clips and install the front door lower frame bracket garnish.


Hide 67491A 33.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH (for 14 Speakers)

B190538

a.

Connect the connector.


b.

Engage the 3 clips and install the front door lower frame bracket garnish.


Hide 34.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

CAUTION:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 35.INSPECT SRS WARNING LIGHT