Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR
RM27L0U _59 Vehicle Exterior _049349 DOOR / HATCH _0235959 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL CUSHION

a.
B192118

Install the cushions onto the door panel.


Hide 69203A 2.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.
B195034

Slide the rear door outside handle frame subassembly and engage the claw and install it.


b.

Using a T30 "TORX" wrench, tighten the screw

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69241G 3.INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD

a.
B192116

Engage the 2 claws and install the rear door outside handle front pad.


Hide 69242G 4.INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD

a.
B192115

Engage the 2 claws and install the rear door outside handle rear pad.


Hide 69230 5.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B192113

Install the rear door outside handle assembly by pushing it in the direction indicated by the arrow mark shown in the illustration.


Hide 69227J 6.INSTALL REAR DOOR OUTSIDE HANDLE COVER

a.
B192111

Using "TORX" socket wrench T30, install the rear door outside handle cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 67887A 8.INSTALL REAR DOOR NO. 2 WEATHERSTRIP

B192110

a.

Engage the 17 clips and install the rear door No. 2 weatherstrip.


Hide 67871 9.INSTALL REAR DOOR WEATHERSTRIP

B192109

a.

Engage the 42 clips and install the rear door weatherstrip.


Hide 68630D 10.INSTALL REAR DOOR CHECK ASSEMBLY

B190589

a.

Apply MP grease to the sliding areas of the rear door check assembly.


b.

Install the rear door check assembly onto the door panel with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent



d.

Install the rear door check assembly onto the body panel with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 69803 11.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY

a.
B192108E02
1.406,0.198 1.531,0.365 0.125,0.167 10 true A

Apply MP grease to the sliding and rotating areas of the rear door window regulator sub-assembly.

NOTICE:

Do not apply grease to the front door window regulator spring.



b.

Loosely screw bolt A onto the rear door window regulator sub-assembly.


c.

Insert the rear door window regulator sub-assembly into the door panel. Provisionally tighten bolt A to hang the rear door window regulator sub-assembly on the door panel.

NOTICE:

Do not drop the front door window regulator sub-assembly as it may be damaged.



d.

Install the front door window regulator sub-assembly with the 5 bolts, and tighten bolt A.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the connector.


Hide 68103 12.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

a.
B190588

Install the rear door glass sub-assembly onto the rear door window regulator with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67405B 13.INSTALL REAR DOOR WINDOW GUIDE FRONT SUB-ASSEMBLY

a.
B190587

Install the rear door window guide front sub-assembly with the 2 bolts

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67407F 14.INSTALL REAR DOOR WINDOW FRAME REAR LOWER SUB-ASSEMBLY

B190586

a.

Install the rear door window frame rear lower sub-assembly with the nut and 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67497 15.INSTALL REAR DOOR FRAME BRACKET

a.
B194496

Engage the claw and install the sunshade hook.


Hide 68152C 16.INSTALL REAR DOOR GLASS RUN

a.
B190585

Install the rear door glass run.


Hide 68163H 17.INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP

Hide 75765A 18.INSTALL REAR DOOR WINDOW FRAME REAR MOULDING

Hide 67841E 19.INSTALL REAR DOOR SERVICE HOLE COVER

a.
B195022

Apply butyl tape to the door panel, then install a new rear door service hole cover as shown in the illustration.

HINT:
·

When installing the service hole cover, pull the links and connectors out through the service hole.

·

There should be no wrinkles or folds after attaching the service hole cover.

·

After attaching the service hole cover, check the quality of the seal.




b.
B190584

Engage the clamps and connect the connectors.


Hide 67626C 20.INSTALL REAR DOOR TRIM NO. 2 BRACKET

a.
B190583

Install the rear door trim No. 2 bracket with the 2 screws.


Hide 86160Y 21.INSTALL REAR NO. 1 SPEAKER ASSEMBLY

Hide 68173B 22.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP

a.
B190582

Install the rear door glass inner weatherstrip on the rear door trim board sub-assembly and fold down the 8 claws, as shown in the illustration.


Hide 69205A 23.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B190545

Install the rear door inside handle sub-assembly with the 3 screws.


Hide 69277 24.INSTALL REAR DOOR INSIDE HANDLE BEZEL

a.
B190544

Install the rear door inside handle bezel with the 4 screws.


Hide 67603 25.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B190580

Connect the rear door lock remote control cable and the rear door inside locking cable.


b.

Connect the connector.


c.
B190579

Engage the 9 clips and install the rear door trim board sub-assembly.


d.
B190578

Tighten the 2 screws.


e.

Install the rear door armrest cover.


Hide 69283A 26.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

B190576

a.

Engage the 4 claws and install the rear door inside handle bezel plug.


Hide 74271A 27.INSTALL REAR DOOR ARMREST BASE UPPER PANEL

a.

Connect the connector.


b.
B190574

Engage the 2 clips and 5 claws and install the rear door armrest base upper panel.


Hide 67673A 28.INSTALL REAR DOOR FRAME GARNISH

a.
B190577

Engage the 6 clips and install the rear door frame garnish.


Hide 29.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

CAUTION:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 30.INSPECT SRS WARNING LIGHT