Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR CLOSER SYSTEM
RM27L0U _59 Vehicle Exterior _049349 DOOR / HATCH _0235967 BACK DOOR CLOSER SYSTEM J

DOOR / HATCH  BACK DOOR CLOSER SYSTEM  Back Door Closer does not Operate  


DESCRIPTION

When the back door closer does not operate, one of the following may be the cause: 1) improper fit of back door, or a foreign object is stuck in back door, or 2) initialization of the power back door ECU, or 3) power back door ECU power source circuit malfunction, or 4) back door lock circuit malfunction, or 5) power back door ECU malfunction.

WIRING DIAGRAM

U153293E01
0.047,0.44 1.221,0.622 1.175,0.182 10 to IG1 No. 3 Relay 0.075,0.99 0.696,1.168 0.620,0.178 10 to Battery 1.9,0.466 2.798,0.619 0.898,0.153 10 ECU-IG No. 2 2.171,1.003 2.479,1.156 0.309,0.153 10 PBD 2.067,1.504 2.595,1.660 0.527,0.156 10 ECU-B1 5.92,0.334 6.098,0.487 0.178,0.153 10 IG 5.91,0.866 6.043,1.009 0.133,0.143 10 B 5.91,1.383 6.329,1.526 0.419,0.143 10 ECUB 5.753,0.268 5.875,0.416 0.123,0.148 10 8 5.697,0.78 5.895,0.928 0.198,0.148 10 12 5.682,1.292 5.870,1.450 0.188,0.158 10 10 5.925,2.629 6.234,2.788 0.308,0.159 10 DC+ 5.905,2.111 6.198,2.266 0.293,0.155 10 DC- 2.382,2.022 2.771,2.175 0.389,0.153 10 ACT+ 2.402,2.547 2.766,2.697 0.364,0.150 10 ACT- 5.738,2.017 5.855,2.175 0.118,0.158 10 1 5.753,2.549 5.850,2.697 0.097,0.148 10 2 2.841,2.537 2.943,2.711 0.102,0.174 10 2 2.823,2.021 2.940,2.171 0.118,0.150 10 1 2.458,2.937 2.761,3.087 0.303,0.150 10 CLS 2.422,3.49 2.766,3.645 0.344,0.155 10 FSW 2.661,4.156 2.778,4.319 0.118,0.163 10 S 0.716,4.144 0.849,4.296 0.133,0.153 10 E 2.825,3.489 2.956,3.655 0.131,0.165 10 4 2.837,2.938 2.954,3.076 0.118,0.138 10 5 0.568,4.154 0.671,4.302 0.102,0.148 10 3 2.828,4.152 2.935,4.305 0.107,0.153 10 6 5.93,3.021 6.239,3.179 0.308,0.158 10 HAF 5.91,3.584 6.234,3.736 0.324,0.153 10 POS 5.682,2.94 5.870,3.086 0.188,0.146 10 22 5.667,3.51 5.860,3.655 0.193,0.145 10 24 3.933,4.237 4.372,4.385 0.439,0.148 10 BDCY 4.451,4.042 4.868,4.189 0.417,0.147 10 OCTY 3.934,5.98 4.285,6.117 0.351,0.138 10 GND 3.929,5.606 4.323,5.764 0.394,0.158 10 CTYE 3.375,4.171 3.551,4.315 0.177,0.144 10 10 5.268,3.99 5.441,4.126 0.173,0.136 10 17 3.374,5.534 3.552,5.696 0.178,0.163 10 20 3.436,5.893 3.554,6.048 0.118,0.155 10 6 3.891,6.402 4.904,6.540 1.012,0.138 10 Back Door ECU 5.922,4.047 6.224,4.199 0.302,0.152 10 FUL 5.914,4.645 6.272,4.787 0.357,0.142 10 GND 5.695,4.557 5.867,4.714 0.172,0.157 10 11 5.69,3.982 5.872,4.126 0.182,0.145 10 20 1.322,3.146 2.131,3.300 0.809,0.154 10 Latch Switch 1.31,3.747 2.218,3.910 0.908,0.164 10 Sector Switch 1.121,4.377 2.402,4.714 1.281,0.336 10 Back Door Courtesy Light Switch 3.624,4.244 3.820,4.400 0.195,0.156 10 V3 3.623,5.62 3.818,5.777 0.195,0.156 10 V3 4.999,4.055 5.197,4.204 0.198,0.150 10 V2 3.629,5.987 3.827,6.137 0.198,0.150 10 V2 0.871,5.283 1.067,5.432 0.197,0.148 10 V5 1.21,5.272 2.254,5.428 1.044,0.156 10 Back Door Lock 5.57,5.01 5.855,5.168 0.285,0.158 10 O30 5.317,5.17 7.072,5.566 1.755,0.396 10 Power Back Door Drive Unit (Power Back Door ECU)

PROCEDURE

1.CHECK BACK DOOR LOCK FUNCTION
a.

Check if the back door is fully closed by hand.



OK

2.INITIALIZE POWER BACK DOOR ECU

NG

IMPROPER FIT OF BACK DOOR, OR A FOREIGN OBJECT IS STUCK IN BACK DOOR

2.INITIALIZE POWER BACK DOOR ECU
a.

Check that the power back door drive unit (power back door ECU) can be initialized (See page Vehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION).



NEXT

3.CHECK BACK DOOR CLOSER SYSTEM
3.CHECK BACK DOOR CLOSER SYSTEM
a.

Check that the back door closer system operates normally.

OK:

Back door closer system operates normally.




OK

END

NG

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Check for the DTCs (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
B2250 is output B
B2251 is output C



A

5.INSPECT FUSES (ECU-IG NO. 2, ECU-B1, PBD)

B

C

5.INSPECT FUSES (ECU-IG NO. 2, ECU-B1, PBD)
a.

Remove the ECU-IG No. 2, ECU-B1, and PBD fuses.


E344963E01
0.448,0.729 0.635,0.729 0.635,0.729 1.198,1.49 true 2.083,2.448 2.271,2.448 2.271,2.448 2.5,1.885 true 4.99,2.052 5.177,2.052 5.177,2.052 5.521,1.552 true 0.281,0.083 2.156,0.292 1.875,0.208 10 false Engine Room Relay Block: 0.125,0.646 0.635,0.823 0.51,0.177 10 false PBD 1.563,2.365 2.625,2.563 1.063,0.198 10 false ECU-B1 3.896,0.167 5.698,0.385 1.802,0.219 10 false Main Body ECU: 4.115,1.948 5.177,2.146 1.063,0.198 10 false ECU-IG No. 2

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-IG No. 2 Always Below 1 Ω
ECU-B1 Always Below 1 Ω
PBD Always Below 1 Ω



c.

Reinstall the fuses.



OK

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.

Disconnect the O30 power back door ECU connector.


b.
U153172E02
1.927,2.156 1.552,2.771 true 2.25,2.104 2.344,2.75 true 2.708,2.156 2.875,2.75 true 0.083,0.063 2.458,0.396 2.375,0.333 10 false Front view of wire harness connector: (to Power Back Door ECU) 1.438,2.823 1.677,3 0.24,0.177 10 false IG 2.073,2.802 2.563,2.979 0.49,0.177 10 false ECUB 2.875,2.802 3.021,2.979 0.146,0.177 10 false B 0.135,2 0.448,2.177 0.313,0.177 10 false O30

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O30-8 (IG) - Body ground Ignition switch ON 11 to 14 V
O30-10 (ECUB) - Body ground Always 11 to 14 V
O30-12 (B) - Body ground Always 11 to 14 V



c.

Reconnect the power back door ECU connector.



OK

7.CHECK HARNESS AND CONNECTOR (BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (BODY GROUND)
a.

Disconnect the O30 power back door ECU connector.


b.
U153173E02
2.448,2.083 2.083,2.708 true 0.073,0.042 2.448,0.375 2.375,0.333 10 false Front view of wire harness connector: (to Power Back Door ECU) 1.896,2.719 2.292,2.896 0.396,0.177 10 false GND 0.198,1.979 0.51,2.156 0.313,0.177 10 false O30

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O30-11 (GND) - Body ground Always Below 1 Ω



c.

Reconnect the power back door ECU connector.



OK

8.INSPECT BACK DOOR LOCK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BACK DOOR LOCK
B191744E12
5.896,1.698 6,1.698 6,1.698 6.406,1.281 true 5.979,2.198 6.083,2.198 6.083,2.198 6.406,1.469 true 6.823,2 6.729,2 6.729,2 6.594,1.479 true 5.552,0.625 5.656,0.625 5.656,0.625 6.385,1.021 true 6.792,0.25 6.708,0.25 6.708,0.25 6.594,1 true 5.74,1.635 5.896,1.781 0.156,0.146 10 false E 4.771,1.313 5.188,1.563 0.417,0.25 10 true Close 3.719,1.229 4.24,1.531 0.521,0.302 10 true Release 2.26,0.781 2.927,0.927 0.667,0.146 10 false Over-latch 2.188,1.094 2.781,1.25 0.594,0.156 10 false Full-latch 1.99,1.833 2.615,1.979 0.625,0.146 10 false Half-latch 1.708,2.271 2.438,2.438 0.729,0.167 10 false Open-latch 6.875,1.927 7.063,2.073 0.188,0.146 10 false S 5.667,2.135 5.979,2.281 0.313,0.146 10 false CLS 6.813,0.156 7.156,0.354 0.344,0.198 10 false ACT- 5.167,0.563 5.563,0.708 0.396,0.146 10 false ACT+

a.

Remove the back door lock (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL).


b.

Apply battery voltage and check the operation of the door lock motor.

Apply Battery Voltage:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2 (ACT-)
Battery negative (-) → Terminal 1 (ACT+)
Latch turns to open-latch position
Battery positive (+) → Terminal 1 (ACT+)
Battery negative (-) → Terminal 2 (ACT-)
Latch turns to full-latch position



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Latch Switch

Tester Connection Door Lock Latch Position Specified Condition
5 (CLS) - 3 (E) Over-latch Below 1 Ω
5 (CLS) - 3 (E) Open-latch 10 kΩ or higher
5 (CLS) - 3 (E) Full-latch 10 kΩ or higher
5 (CLS) - 3 (E) Half-latch 10 kΩ or higher


Standard Resistance:

Back Door Courtesy Light Switch

Tester Connection Door Lock Latch Position Specified Condition
6 (S) - 3 (E) Over-latch 10 kΩ or higher
6 (S) - 3 (E) Open-latch Below 1 Ω
6 (S) - 3 (E) Full-latch 10 kΩ or higher
6 (S) - 3 (E) Half-latch Below 1 Ω




OK

9.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK - POWER BACK DOOR ECU AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK

9.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK - POWER BACK DOOR ECU AND BODY GROUND)
a.

Disconnect the V5 door lock connector.

B443244E02
0.781,1.135 1.198,1.365 0.417,0.229 3.677,1.083 4.094,1.313 0.417,0.229 0.76,2.906 1.177,3.135 0.417,0.229 3.729,2.854 4.146,3.083 0.417,0.229 1.802,1.24 2.156,0.865 2.156,0.865 2.323,0.865 true 5.438,1.427 5.635,1.75 5.635,1.75 5.823,1.75 true 1.385,3.302 1.198,3.469 1.198,3.469 1.031,3.469 true 4.573,3.563 4.74,3.563 4.74,3.563 4.99,3.313 true 1.833,1.354 2.146,1.177 2.146,1.177 2.313,1.177 true 1.833,1.49 2.094,1.646 2.094,1.646 2.281,1.646 true 1.729,1.51 1.552,1.708 1.552,1.708 1.406,1.708 true 1.708,1.219 1.51,0.958 1.51,0.958 1.365,0.958 true 4.604,1.219 4.427,0.927 4.427,0.927 4.281,0.927 true 4.708,1.271 4.479,1.563 4.479,1.563 4.333,1.563 true 5.271,1.448 5.031,1.74 5.031,1.74 4.885,1.74 true 4.406,2.615 4.573,2.615 4.573,2.615 5.083,3.177 true 0.594,0.063 2.885,0.406 2.292,0.344 10 false Front view of wire harness connector: (to Back Door Lock) 4.208,0.063 6.448,0.417 2.24,0.354 10 false Front view of wire harness connector: (to Power Back Door ECU) 0.76,1.958 3.042,2.302 2.281,0.344 10 false Front view of wire harness connector: (to Back Door ECU) 4.26,1.844 6.542,2.188 2.281,0.344 10 false Front view of wire harness connector: (to Back Door ECU) 0.906,1.188 1.156,1.354 0.25,0.167 10 false V5 2.375,0.76 2.885,0.938 0.51,0.177 10 false ACT+ 2.375,1.552 2.823,1.771 0.448,0.219 10 false CLS 5.854,1.667 6.302,1.885 0.448,0.219 10 false HAF 3.74,1.125 4.198,1.344 0.458,0.219 10 false O30 0.896,2.948 1.146,3.115 0.25,0.167 10 false V2 0.635,3.385 1.083,3.604 0.448,0.219 10 false OCTY 3.844,2.906 4.094,3.073 0.25,0.167 10 false V3 4.156,3.479 4.604,3.698 0.448,0.219 10 false CTYE 2.365,1.083 2.875,1.26 0.51,0.177 10 false E 1.271,1.625 1.563,1.844 0.292,0.219 10 false S 1,0.865 1.51,1.042 0.51,0.177 10 false ACT- 4.656,1.656 5.104,1.875 0.448,0.219 10 false FUL 4,0.823 4.448,1.042 0.448,0.219 10 false DC- 3.979,1.469 4.427,1.688 0.448,0.219 10 false DC+ 3.948,2.542 4.396,2.76 0.448,0.219 10 false BDCY


b.

Disconnect the O30 ECU connector.


c.

Disconnect the V2 and V3 ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V5-2 (ACT-) - O30-2 (DC+) Always Below 1 Ω
V5-1 (ACT+) - O30-1 (DC-) Always Below 1 Ω
V5-5 (CLS) - O30-22 (HAF) Always Below 1 Ω
V5-6 (S) - V3-10 (BDCY) Always Below 1 Ω
V5-3 (E) - V3-20 (CTYE) Always Below 1 Ω
V2-17 (OCTY) - O30-20 (FULL) Always Below 1 Ω
O30-2 (DC+) - Body ground Always 10 kΩ or higher
O30-1 (DC-) - Body ground Always 10 kΩ or higher
O30-22 (HAF) - Body ground Always 10 kΩ or higher
O30-20 (FUL) - Body ground Always 10 kΩ or higher



e.

Reconnect the door lock and ECU connector.



OK

10.REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
a.

Temporarily replace the power back door drive unit (power back door ECU) with a new or normally functioning one (See page Vehicle Exterior>DOOR / HATCH>POWER BACK DOOR DRIVE UNIT>REMOVAL).



NEXT

11.CHECK BACK DOOR CLOSER SYSTEM (OPERATION)
11.CHECK BACK DOOR CLOSER SYSTEM (OPERATION)
a.

Check that the back door closer operates normally.

OK:

It operates normally.




OK

END (POWER BACK DOOR UNIT (POWER BACK DOOR ECU) DEFECTIVE)

NG

REPLACE BACK DOOR ECU