Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Memory)
RM27L0U _59 Vehicle Exterior _049350 MIRROR (EXT) _0235974 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Power Retractable Mirrors do not Operate with Power Retract Mirror Switch  


SYSTEM DESCRIPTION

This circuit detects the conditions of the mirror retract switch.

The outer mirror switch sends information about the operating condition of the mirror retract switch (switch input signals) through the CAN communication line. Then the switch input signals are sent to the outer mirror control ECU.

WIRING DIAGRAM

B191615E03
0.875,5.354 2.604,5.531 1.729,0.177 10 false : CAN Communication Line 0.271,3.854 0.49,4.052 0.219,0.198 10 false J6 2.188,3.813 3.219,3.99 1.031,0.177 10 false Main Body ECU 3.677,4.24 3.927,4.406 0.25,0.167 10 false M7 5.781,1.833 6.01,2.021 0.229,0.188 10 false M5 5.75,4.219 5.927,4.406 0.177,0.188 10 false L6 2.25,1.417 2.615,1.583 0.365,0.167 10 false AMR 1.073,1.417 1.542,1.604 0.469,0.188 10 false MR 1.99,1.24 2.458,1.427 0.469,0.188 10 false 9 1.375,1.313 1.844,1.5 0.469,0.188 10 false 7 2.281,2.302 2.594,2.49 0.313,0.188 10 false RET 1.073,2.281 1.542,2.469 0.469,0.188 10 false MF 1.073,3.156 1.542,3.344 0.469,0.188 10 false E2 1.99,2.104 2.458,2.292 0.469,0.188 10 false 6 1.375,2.177 1.844,2.365 0.469,0.188 10 false 8 1.375,3.063 1.844,3.25 0.469,0.188 10 false 4 4.583,3.198 4.906,3.385 0.323,0.188 10 false MR+ 4.604,3.688 4.906,3.885 0.302,0.198 10 false MR- 5.01,3.094 5.479,3.281 0.469,0.188 10 false 5 5.01,3.594 5.479,3.781 0.469,0.188 10 false 6 5.875,3.188 6.344,3.375 0.469,0.188 10 false MR 5.875,3.688 6.344,3.875 0.469,0.188 10 false MF 5.656,3.094 6.125,3.281 0.469,0.188 10 false 7 5.656,3.594 6.125,3.781 0.469,0.188 10 false 8 4.615,0.875 5.083,1.063 0.469,0.188 10 false MR+ 4.615,1.365 5.083,1.552 0.469,0.188 10 false MR- 5.01,0.781 5.479,0.969 0.469,0.188 10 false 1 5.01,1.271 5.479,1.458 0.469,0.188 10 false 2 5.875,0.906 6.146,1.094 0.271,0.188 10 false MR 5.875,1.385 6.125,1.563 0.25,0.177 10 false MF 5.667,0.781 5.792,0.969 0.125,0.188 10 false 7 5.667,1.281 5.813,1.458 0.146,0.177 10 false 8 1.938,1.427 2.167,1.604 0.229,0.177 10 false H1 1.948,2.292 2.156,2.458 0.208,0.167 10 false H3 0.25,4.021 1.448,4.208 1.198,0.188 10 false Outer Mirror Switch 3.677,4.406 5.229,4.594 1.552,0.188 10 false Outer Mirror Control ECU 5.75,4.385 6.771,4.74 1.021,0.354 10 false Outer Rear View Mirror RH 5.771,1.99 6.844,2.323 1.073,0.333 10 false Outer Rear View Mirror LH

PROCEDURE

1.CHECK DTC
a.

Use the Techstream to check if the CAN communication system is functioning normally (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN DTC is not output A
CAN DTC is output B



A

2.READ VALUE USING TECHSTREAM (MIRROR RETRACT SWITCH)

B

2.READ VALUE USING TECHSTREAM (MIRROR RETRACT SWITCH)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the Techstream, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Outer Mirror Fold SW Mirror retract switch signal / ON or OFF ON: Switch is on (retracting)
OFF: Switch is off
-

OK:

On the Techstream screen, each item changes between ON and OFF according to above chart.




OK

3.PERFORM ACTIVE TEST USING TECHSTREAM (MIRROR RETRACT FUNCTION)

NG

4.INSPECT OUTER MIRROR SWITCH (MIRROR RETRACT SWITCH)
3.PERFORM ACTIVE TEST USING TECHSTREAM (MIRROR RETRACT FUNCTION)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Body Electrical / Mirror / Active Test.


e.

According to the display on the Techstream, perform the Active Test.

Mirror
Tester Display Test Part Control Range Diagnostic Note
Mirror Fold Mirror retract operation FOLD/OFF -
Mirror Return Mirror retract operation RETURN/OFF -

Result
Result Proceed to
Outer rear view mirror operates normally A
Outer rear view mirror LH does not operate normally B
Outer rear view mirror RH does not operate normally C



A

REPLACE OUTER MIRROR CONTROL ECU

B

6.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

C

8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
4.INSPECT OUTER MIRROR SWITCH (MIRROR RETRACT SWITCH)
a.
B167772E05
0.068,2.18 2.533,2.528 2.465,0.348 10 Component without harness connected: (Outer Mirror Switch) 1.804,4.201 2.011,4.382 0.207,0.181 10 E2 1.852,3.814 1.923,4.173 false 0.809,4.201 1.026,4.382 0.218,0.181 10 MF 1.006,4.175 1.232,3.814 false 1.152,4.201 1.385,4.382 0.233,0.181 10 MR 1.32,4.173 1.383,3.814 false

Remove the switch (See page Vehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (MR) - 4 (E2) Pressed (Driving position) Below 1 Ω
Not pressed 10 kΩ or higher
8 (MF) - 4 (E2) Pressed (Retracts) Below 1 Ω
Not pressed 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE OUTER MIRROR SWITCH

5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the H1and H3 ECU connector.

B443122E01
0.323,1.677 0.667,1.885 0.344,0.208 2.917,1.604 3.26,1.813 0.344,0.208 4.958,1.656 5.302,1.865 0.344,0.208 1.313,2.177 1.396,1.948 true 1.865,2.188 1.802,1.938 true 2.073,2.188 1.958,1.938 true 3.792,2.385 3.792,2.073 true 6.073,2.375 6.219,1.74 true 0.115,0.188 2.385,0.542 2.271,0.354 10 false Front view of wire harness connector: (to Outer Mirror Switch) 2.479,0.156 4.75,0.51 2.271,0.354 10 false Front view of wire harness connector: (to Main Body ECU) 4.896,0.167 7.135,0.542 2.24,0.375 10 false Front view of wire harness connector: (to Main Body ECU) 0.417,1.688 0.615,1.875 0.198,0.188 10 false J6 3.01,1.615 3.208,1.802 0.198,0.188 10 false H1 5.042,1.667 5.24,1.854 0.198,0.188 10 false H3 1.208,2.219 1.406,2.406 0.198,0.188 10 false E2 1.76,2.229 2.021,2.396 0.26,0.167 10 false MR 2.052,2.229 2.313,2.396 0.26,0.167 10 false MF 3.667,2.406 4.01,2.583 0.344,0.177 10 false AMR 5.948,2.396 6.25,2.573 0.302,0.177 10 false RET


b.

Disconnect the J6 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J6-4 (E2) - Body ground Always Below 1 Ω
J6-7 (MR) - H1-9 (AMR) Always Below 1 Ω
J6-7 (MR) - Body ground Always 10 kΩ or higher
J6-8 (MF) - H3-6 (RET) Always Below 1 Ω
J6-8 (MF) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Remove the mirror LH (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL).

B443052E02
4.865,1.146 5.021,1.146 5.021,1.146 5.104,1.906 false 5.5,1.188 5.323,1.188 5.323,1.188 5.24,1.917 false 1.521,0.229 1.76,0.427 0.24,0.198 10 false (A) 0.99,1.094 1.198,1.292 0.208,0.198 10 false (B) 0.969,2.375 1.177,2.573 0.208,0.198 10 false (C) 1.938,3.073 2.146,3.271 0.208,0.198 10 false (D) 2.583,3.333 2.792,3.531 0.208,0.198 10 false (E) 4.615,1.083 4.833,1.271 0.219,0.188 10 false MF 5.563,1.094 5.781,1.281 0.219,0.188 10 false MR 1.75,0.229 2.833,0.427 1.083,0.198 10 false Forward Position 0.823,2.594 1.906,2.792 1.083,0.198 10 false Driving Position 2.802,3.344 3.99,3.542 1.188,0.198 10 false Retracted Position 4.313,0.094 6.719,0.448 2.406,0.354 10 false Component without harness connected: (Outer Rear View Mirror LH)


b.

Check the retractable mirror's movement.

i.

For each mirror position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Measurement Condition Mirror Position Specified Condition
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Forward position (A) Moves from (A) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Driving position (C) Moves from (C) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Retracted position (E) Moves from (E) to driving position (C)


NOTICE:
·

Disconnect and reconnect the battery once between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.






OK

7.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

7.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU)
a.

Disconnect the M7 ECU connector.

B443123E01
0.802,1.625 1.208,1.823 0.406,0.198 3.958,1.583 4.365,1.781 0.406,0.198 2.094,2.313 2.219,1.771 true 2.479,2.313 2.344,1.781 true 4.667,2.271 4.833,1.625 true 5.188,2.281 5.052,1.635 true 4.24,0.104 6.5,0.458 2.26,0.354 10 false Front view of wire harness connector: (to Outer Mirror Control ECU) 0.396,0.115 2.656,0.469 2.26,0.354 10 false Front view of wire harness connector: (to Outer Rear view Mirror LH) 0.896,1.635 1.115,1.813 0.219,0.177 10 false M5 4.063,1.594 4.281,1.771 0.219,0.177 10 false M7 1.969,2.354 2.219,2.531 0.25,0.177 10 false MR 2.458,2.354 2.708,2.531 0.25,0.177 10 false MF 4.49,2.313 4.823,2.5 0.333,0.188 10 false MR+ 5.125,2.313 5.458,2.5 0.333,0.188 10 false MR-


b.

Disconnect the M5 mirror connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M5-7 (MR) - M7-1 (MR+) Always Below 1 Ω
M5-7 (MR) - Body ground Always 10 kΩ or higher
M5-8 (MF) - M7-2 (MR-) Always Below 1 Ω
M5-8 (MF) - Body ground Always 10 kΩ or higher




OK

REPLACE OUTER MIRROR CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Remove the mirror RH (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL).

B443053E02
5.104,1.969 5.01,1.396 5.01,1.396 4.865,1.396 false 5.271,1.969 5.333,1.406 5.333,1.406 5.49,1.406 false 2.458,0.188 2.698,0.396 0.24,0.208 10 false (A) 2.979,1.115 3.219,1.323 0.24,0.208 10 false (B) 2.99,2.167 3.229,2.375 0.24,0.208 10 false (C) 2.208,2.854 2.448,3.063 0.24,0.208 10 false (D) 1.344,3.188 1.583,3.396 0.24,0.208 10 false (E) 4.396,0.302 6.792,0.667 2.396,0.365 10 false Component without harness connected: (Outer Rear View Mirror RH) 4.625,1.333 4.844,1.51 0.219,0.177 10 false MF 5.521,1.333 5.74,1.51 0.219,0.177 10 false MR 2.698,0.198 3.76,0.375 1.063,0.177 10 false Forward Position 2.313,2.458 3.365,2.813 1.052,0.354 10 true Driving Position 1.563,3.188 2.729,3.375 1.167,0.188 10 false Retracted Position


b.

Check the retractable mirror's movement.

i.

For each mirror position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Measurement Condition Mirror Position Specified Condition
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Forward position (A) Moves from (A) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Driving position (C) Moves from (C) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Retracted position (E) Moves from (E) to driving position (C)


NOTICE:
·

Disconnect and reconnect the battery once between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.






OK

9.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

9.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)
a.

Disconnect the M7 ECU connector.

B443123E02
0.781,1.542 1.125,1.719 0.344,0.177 4.01,1.573 4.354,1.75 0.344,0.177 2.042,2.323 2.219,1.771 true 2.479,2.323 2.344,1.781 true 4.708,2.354 4.823,1.917 true 5.156,2.365 5.073,1.906 true 0.281,0.188 2.594,0.594 2.313,0.406 10 false Front view of wire harness connector: (to Outer Rear view Mirror RH) 4.177,0.167 6.49,0.573 2.313,0.406 10 false Front view of wire harness connector: (to Outer Mirror Control ECU) 0.875,1.542 1.083,1.74 0.208,0.198 10 false L6 1.938,2.354 2.146,2.552 0.208,0.198 10 false MR 2.406,2.354 2.615,2.552 0.208,0.198 10 false MF 4.094,1.573 4.302,1.771 0.208,0.198 10 false M7 4.563,2.385 4.875,2.573 0.313,0.188 10 false MR+ 5.073,2.375 5.385,2.563 0.313,0.188 10 false MR-


b.

Disconnect the L6 mirror connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L6-7 (MR) - M7-5 (MR+) Always Below 1 Ω
L6-7 (MR) - Body ground Always 10 kΩ or higher
L6-8 (MF) - M7-6 (MR-) Always Below 1 Ω
L6-8 (MF) - Body ground Always 10 kΩ or higher




OK

REPLACE OUTER MIRROR CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR