Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Memory)
RM27L0U _59 Vehicle Exterior _049350 MIRROR (EXT) _0235974 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Power Mirrors do not Return to Memorized Position  


SYSTEM DESCRIPTION

When the seat memory switch 1 or seat memory switch 2 is pressed, the front power seat switch LH mirror position signal is sent through the CAN communication line to the outer mirror control ECU. The outer mirror control ECU then activates the mirror control motors to move the mirrors to the previously recorded positions.

WIRING DIAGRAM

B191617E04
5.281,5.271 5.531,5.479 0.25,0.208 10 false L6 3.01,5.271 3.271,5.479 0.26,0.208 10 false M8 1.031,6.333 2.74,6.521 1.708,0.188 10 false : CAN Communication Line 0.938,5.271 1.208,5.479 0.271,0.208 10 false X11 0.844,2.271 1.094,2.458 0.25,0.188 10 false M6 5.354,1.792 5.583,1.948 0.229,0.156 10 false E1 5.354,1.052 5.76,1.208 0.406,0.156 10 false HSRL 5.354,1.417 5.75,1.573 0.396,0.156 10 false VSRL 5.354,0.667 5.583,0.823 0.229,0.156 10 false VC 4.229,1.771 4.427,1.927 0.198,0.156 10 false E1 4.01,1.042 4.427,1.198 0.417,0.156 10 false HSRL 4.083,1.417 4.417,1.573 0.333,0.156 10 false VSR 4.208,0.667 4.427,0.823 0.219,0.156 10 false VC 5.083,0.604 5.271,0.76 0.188,0.156 10 false 15 5.083,1.354 5.26,1.51 0.177,0.156 10 false 17 5.083,0.979 5.26,1.135 0.177,0.156 10 false 16 5.083,1.708 5.26,1.865 0.177,0.156 10 false 18 4.531,0.604 4.635,0.76 0.104,0.156 10 false 2 4.531,1.354 4.635,1.51 0.104,0.156 10 false 4 4.531,0.979 4.635,1.135 0.104,0.156 10 false 5 4.531,1.719 4.635,1.875 0.104,0.156 10 false 3 5.385,4.771 5.615,4.927 0.229,0.156 10 false E1 5.354,4.031 5.76,4.188 0.406,0.156 10 false HSSR 5.354,4.406 5.75,4.563 0.396,0.156 10 false VSSR 5.354,3.656 5.583,3.813 0.229,0.156 10 false VC 4.219,4.76 4.417,4.917 0.198,0.156 10 false E1 3.99,4.031 4.406,4.188 0.417,0.156 10 false HSRR 3.99,4.396 4.438,4.552 0.448,0.156 10 false VSRR 4.198,3.646 4.427,3.802 0.229,0.156 10 false VC 5.083,3.583 5.26,3.74 0.177,0.156 10 false 15 5.083,4.698 5.26,4.854 0.177,0.156 10 false 18 5.083,3.958 5.26,4.115 0.177,0.156 10 false 16 5.083,4.323 5.26,4.479 0.177,0.156 10 false 17 4.521,3.583 4.708,3.74 0.188,0.156 10 false 22 4.521,4.333 4.708,4.49 0.188,0.156 10 false 24 4.521,3.958 4.698,4.115 0.177,0.156 10 false 25 4.521,4.698 4.698,4.854 0.177,0.156 10 false 23 3.115,1.781 3.583,1.938 0.469,0.156 10 false MSWE 3.115,0.667 3.375,0.823 0.26,0.156 10 false MM 3.115,1.417 3.344,1.573 0.229,0.156 10 false M2 2.073,1.781 2.188,1.938 0.115,0.156 10 false E 1.823,0.667 2.177,0.823 0.354,0.156 10 false MRY 1.958,1.427 2.177,1.583 0.219,0.156 10 false M2 3.115,1.042 3.344,1.198 0.229,0.156 10 false M1 1.958,1.042 2.177,1.198 0.219,0.156 10 false M1 2.906,1.354 3.01,1.51 0.104,0.156 10 false 7 2.906,0.604 3.01,0.76 0.104,0.156 10 false 9 2.833,1.719 3.01,1.875 0.177,0.156 10 false 10 2.292,1.354 2.396,1.51 0.104,0.156 10 false 3 2.906,0.979 3.01,1.135 0.104,0.156 10 false 8 2.292,1.719 2.396,1.875 0.104,0.156 10 false 4 2.292,0.604 2.396,0.76 0.104,0.156 10 false 1 2.292,0.979 2.396,1.135 0.104,0.156 10 false 2 0.833,2.427 2.135,2.615 1.302,0.188 10 false Seat Memory Switch 5.292,2.281 5.531,2.469 0.24,0.188 10 false M5 5.292,2.438 6.74,2.781 1.448,0.344 10 false Outer Rear View Mirror Assembly LH 0.938,5.427 2.073,5.781 1.135,0.354 10 false Front Power Seat Switch LH 3.01,5.458 4.563,5.667 1.552,0.208 10 false Outer Mirror Control ECU 5.281,5.427 6.698,5.802 1.417,0.375 10 false Outer Rear View Mirror Assembly RH

PROCEDURE

1.CHECK DTC
a.

Use the Techstream to check if the CAN communication system is functioning normally (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN DTC is not output A
CAN DTC is output B



A

2.CHECK POWER MIRROR CONTROL FUNCTION

B

2.CHECK POWER MIRROR CONTROL FUNCTION
a.

Check that the mirror surface positions of the outer rear view mirror LH and RH can be moved using the outer mirror switch.

OK:

Mirror surface positions of the outer rear view mirror LH and RH can be moved using the outer mirror switch.




OK

3.READ VALUE USING TECHSTREAM (MIRROR POSITION MEMORY)

NG

GO TO PROBLEM SYMPTOMS TABLE (POWER MIRROR CANNOT BE ADJUSTED WITH POWER MIRROR SWITCH)

3.READ VALUE USING TECHSTREAM (MIRROR POSITION MEMORY)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Body Electrical / Mirror / Data List.


e.

According to the display on the Techstream, read the Data List.

Mirror
Tester Display Measurement Item/Display Normal Condition Diagnostic Note
Mirror Memory No. 1 Mirror position memorized in seat memory switch memory M1 / ON or OFF ON: Memorized
OFF: Not memorized
-
Mirror Memory No. 2 Mirror position memorized in seat memory switch memory M2 / ON or OFF ON: Memorized
OFF: Not memorized
-

OK:

On the Techstream screen, each item changes between ON and OFF according to above chart.




OK

4.READ VALUE USING TECHSTREAM (MIRROR POSITION SENSOR)

NG

REPLACE OUTER MIRROR CONTROL ECU

4.READ VALUE USING TECHSTREAM (MIRROR POSITION SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Body Electrical / Mirror / Data List.


e.

According to the display on the Techstream, read the Data List.

Mirror
Tester Display Measurement Item/Display Normal Condition Diagnostic Note
RH Mir Position Sensor V Passenger side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V Within range from 0 to 5 V -
RH Mir Position Sensor H Passenger side mirror horizontal sensor voltage / MIN: 0 V, MAX: 5 V Within range from 0 to 5 V -
LH Mir Position Sensor V Driver side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V Within range from 0 to 5 V -
LH Mir Position Sensor H Driver side mirror horizontal sensor voltage / MIN: 0 V, MAX: 5 V Within range from 0 to 5 V -

OK:

When mirror control switch is operated, voltage changes within range shown in above chart.


Result
Result Proceed to
LH side mirror does not operate normally A
RH side mirror does not operate normally B
Mirror operates normally C



A

5.CHECK OUTER MIRROR CONTROL ECU

B

7.CHECK OUTER MIRROR CONTROL ECU

C

5.CHECK OUTER MIRROR CONTROL ECU
a.
U153274E02
1.771,1.979 1.771,2.896 true 1.833,1.958 2.25,2.896 true 0.094,0.073 2.375,0.448 2.281,0.375 10 false Component with harness connected: (Outer Mirror Control ECU) 1.604,1.115 1.833,1.281 0.229,0.167 10 false M8 1.667,2.906 1.938,3.073 0.271,0.167 10 false E1 2.188,2.927 2.438,3.094 0.25,0.167 10 false VC

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M8-2 (VC) - M8-3 (E1) Ignition switch ON 3.5 to 5.5 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-3 (E1) - Body ground Always Below 1 Ω




OK

6.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU)

NG

REPLACE OUTER MIRROR CONTROL ECU

6.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU)
a.

Disconnect the M8 ECU connector.

B443121E03
0.604,1.469 0.969,1.688 0.365,0.219 3.75,1.49 4.115,1.708 0.365,0.219 1.604,2.135 1.979,1.833 true 2.333,2.156 2.219,1.854 true 2.635,2.135 2.344,1.844 true 5.198,2.104 4.729,1.583 true 4.74,2.104 4.667,1.573 true 4.198,2.042 4.5,1.594 true 1.938,2.188 2.104,1.844 true 4.469,2.083 4.583,1.583 true 0.271,0.104 2.531,0.479 2.26,0.375 10 false Front view of wire harness connector: (to Outer Rear View Mirror LH) 4.135,0.115 6.396,0.49 2.26,0.375 10 false Front view of wire harness connector: (to Outer Mirror Control ECU) 3.833,1.51 4.073,1.698 0.24,0.188 10 false M8 0.677,1.49 0.917,1.677 0.24,0.188 10 false M5 2.208,2.208 2.594,2.385 0.385,0.177 10 false VSRL 1.427,2.188 1.667,2.375 0.24,0.188 10 false VC 2.656,2.167 2.896,2.354 0.24,0.188 10 false E1 1.729,2.229 2.115,2.406 0.385,0.177 10 false HSRL 4.042,2.094 4.281,2.281 0.24,0.188 10 false VC 4.365,2.125 4.604,2.313 0.24,0.188 10 false E1 4.698,2.125 5.083,2.302 0.385,0.177 10 false VSR 5.125,2.125 5.51,2.302 0.385,0.177 10 false HSRL


b.

Disconnect the M5 mirror connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M5-15 (VC) - M8-2 (VC) Always Below 1 Ω
M5-15 (VC) - Body ground Always 10 kΩ or higher
M5-16 (HSRL) - M8-5 (HSRL) Always Below 1 Ω
M5-16 (HSRL) - Body ground Always 10 kΩ or higher
M5-17 (VSRL) - M8-4 (VSR) Always Below 1 Ω
M5-17 (VSRL) - Body ground Always 10 kΩ or higher
M5-18 (E1) - M8-3 (E1) Always Below 1 Ω
M5-18 (E1)- Body ground Always 10 kΩ or higher




OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK OUTER MIRROR CONTROL ECU
a.
U153275E01
0.089,0.149 2.375,0.527 2.286,0.378 10 Component with harness connected: (Outer Mirror Control ECU) 1.6,1.172 1.828,1.336 0.228,0.164 10 M8 1.668,2.985 1.941,3.151 0.273,0.166 10 E1 2.131,2.985 2.424,3.151 0.292,0.166 10 VC 1.782,2.023 1.782,2.985 false 1.848,2.023 2.262,2.985 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M8-22 (VC) - M8-23 (E1) Ignition switch ON 3.5 to 5.5 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-23 (E1) - Body ground Always Below 1 Ω




OK

8.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)

NG

REPLACE OUTER MIRROR CONTROL ECU

8.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)
a.

Disconnect the M8 ECU connector.

B443121E04
0.604,1.469 0.969,1.688 0.365,0.219 3.75,1.49 4.115,1.708 0.365,0.219 1.656,2.146 1.99,1.833 false 2.313,2.167 2.219,1.844 true 2.604,2.156 2.354,1.833 true 5.208,2.115 4.74,1.688 true 4.229,2.073 4.51,1.677 true 2.01,2.167 2.104,1.823 true 4.51,2.094 4.583,1.698 true 4.792,2.104 4.656,1.677 true 0.271,0.104 2.531,0.479 2.26,0.375 10 false Front view of wire harness connector: (to Outer Rear View Mirror RH) 4.135,0.115 6.396,0.49 2.26,0.375 10 false Front view of wire harness connector: (to Outer Mirror Control ECU) 3.833,1.51 4.073,1.698 0.24,0.188 10 false M8 0.677,1.49 0.917,1.677 0.24,0.188 10 false L6 1.469,2.156 1.708,2.344 0.24,0.188 10 false VC 2.177,2.188 2.552,2.375 0.375,0.188 10 false VSSR 2.635,2.167 2.865,2.344 0.229,0.177 10 false E1 1.76,2.188 2.135,2.375 0.375,0.188 10 false HSSR 4.094,2.094 4.333,2.281 0.24,0.188 10 false VC 4.417,2.104 4.646,2.281 0.229,0.177 10 false E1 4.677,2.115 5.052,2.302 0.375,0.188 10 false VSSR 5.156,2.115 5.531,2.302 0.375,0.188 10 false HSSR


b.

Disconnect the L6 mirror connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L6-15 (VC) - M8-22 (VC) Always Below 1 Ω
L6-15 (VC) - Body ground Always 10 kΩ or higher
L6-16 (HSSR) - M8-25 (HSRR) Always Below 1 Ω
L6-16 (HSSR) - Body ground Always 10 kΩ or higher
L6-17 (VSSR) - M8-24 (VSRR) Always Below 1 Ω
L6-17 (VSSR) - Body ground Always 10 kΩ or higher
L6-18 (E1) - M8-23 (E1) Always Below 1 Ω
L6-18 (E1)- Body ground Always 10 kΩ or higher




OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR