Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Short to B+ in CAN Bus Line

for Preparation Click here


DESCRIPTION

A short to B+ is suspected in the CAN bus wire when the resistance between terminals 6 (CANH) and 16 (BAT), or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.

Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 16 (BAT), or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
  1. Short to B+ in CAN bus wire
  2. ECM
  3. Network gateway ECU
  4. Skid control ECU with Actuator
  5. Steering angle sensor
  6. Yaw rate sensor
  7. Distance control ECU
  8. Junction connector
  9. CAN junction connector

WIRING DIAGRAM


C161558E02


C161559E02


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches, or any doors triggers related ECU and sensor communication with the CAN. This communication will cause the resistance value to change.

1.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM MAIN BUS WIRE)
  1. Turn the ignition switch off.



    C161533E02
  1. Disconnect the ECM connector .



    C118856E51
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Conditon
    D1-6 (CANH) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 2
OK

REPLACE ECM (Click here)  

2.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NETWORK GATEWAY MAIN BUS WIRE)


    E111489E04
  1. Disconnect the Network gateway ECU connector .



    C118856E51
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Conditon
    D1-6 (CANH) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 3
OK

REPLACE NETWORK GATEWAY ECU (Click here)  

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 BRANCH WIRE)
  1. Disconnect the junction connector (J17).



    C152894E24
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Conditon
    D1-6 (CANH) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE DLC3 BRANCH WIRE OR CONNECTOR
OK


4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (JUNCTION CONNECTOR - NETWORK GATEWAY MAIN BUS WIRE)


    C152894E25
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Conditon
    J17-6 (CANH) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J17-17 (CANL) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Result:
    Result
    Proceed to
    OK (without VSC)
    A
    OK (with VSC)
    B
    NG
    C



B
Go to step 6

C
REPAIR OR REPLACE CAN BUS MAIN WIRE (JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
A


5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (JUNCTION CONNECTOR - ECM MAIN BUS WIRE)


    C152894E26
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Conditon
    J17-7 (CANH) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J17-18 (CANL) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (JUNCTION CONNECTOR - ECM)
OK

REPLACE WIRING HARNESS CONNECTOR (JUNCTION CONNECTOR) 

6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (JUNCTION CONNECTOR - CAN JUNCTION CONNECTOR MAIN BUS WIRE)


    C152894E26
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Conditon
    J17-7 (CANH) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J17-18 (CANL) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 10
OK


7.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)


    C152894E27
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Conditon
    J17-10 (CANH) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J17-21 (CANL) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 13
OK


8.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)


    C152894E28
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Conditon
    J17-11 (CANH) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J17-22 (CANL) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Result:
    Result
    Proceed to
    OK (without Dynamic radar cruise control)
    A
    OK (with Dynamic radar cruise control)
    B
    NG
    C



B
Go to step 9

C
Go to step 14
A

REPLACE WIRING HARNESS CONNECTOR (JUNCTION CONNECTOR) 

9.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DISTANCE CONTROL ECU BRANCH WIRE)


    C152894E29
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Conditon
    J17-5 (CANH) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J17-16 (CANL) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 15
OK

REPLACE WIRING HARNESS CONNECTOR (JUNCTION CONNECTOR) 

10.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - JUNCTION CONNECTOR MAIN BUS WIRE)
  1. Disconnect the junction connector (J49).



    C161658E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Conditon
    J49-3 (CANH) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J49-7 (CANL) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (JUNCTION CONNECTOR - CAN JUNCTION CONNECTOR)
OK


11.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - ECM MAIN BUS WIRE)


    C161658E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Conditon
    J49-4 (CANH) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J49-6 (CANL) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (CAN JUNCTION CONNECTOR - ECM)
OK


12.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR BRANCH WIRE)


    C161658E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Conditon
    J49-1 (CANH) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J49-2 (CANL) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 16
OK

REPLACE WIRING HARNESS CONNECTOR (CAN JUNCTION CONNECTOR) 

13.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)


    G024767E61
  1. Disconnect the skid control ECU connector.



    C152894E27
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Conditon
    J17-10 (CANH) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J17-21 (CANL) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE SKID CONTROL ECU BRANCH WIRE OR CONNECTOR
OK

REPLACE ABS & TRACTION ACTUATOR ASSEMBLY (Click here)  

14.CHECK CHECK FOR TO B+ IN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)


    G030155E50
  1. Disconnect the steering angle sensor connector.



    C152894E28
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Conditon
    J17-11 (CANH) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J17-22 (CANL) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE STEERING ANGLE SENSOR BRANCH WIRE OR CONNECTOR
OK

REPLACE STEERING ANGLE SENSOR (Click here)  

15.CHECK CHECK FOR TO B+ IN BUS WIRE (DISTANCE CONTROL ECU BRANCH WIRE)


    C161530E03
  1. Disconnect the distance control ECU connector.



    C152894E29
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Conditon
    J17-5 (CANH) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J17-16 (CANL) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE DISTANCE CONTROL ECU BRANCH WIRE OR CONNECTOR
OK


16.CHECK CHECK FOR TO B+ IN BUS WIRE (YAW RATE SENSOR BRANCH WIRE)


    C161543E03
  1. Disconnect the yaw rate sensor connector.



    C161658E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Conditon
    J49-1 (CANH) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J49-2 (CANL) - D1-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE YAW RATE SENSOR BRANCH WIRE
OK

REPLACE YAW RATE SENSOR (Click here)