Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

OCCUPANT CLASSIFICATION SYSTEM > Trouble in Passenger Airbag ON/OFF Indicator

for Preparation Click here


DESCRIPTION

The occupant classification system detects the front passenger seat condition. It then informs a passenger of the front passenger airbag, the front seat side airbag RH and front seat belt pretensioner RH condition (activated/not activated) by the passenger airbag ON/OFF indicator.

HINT:
Approximately 6 seconds after the ignition switch is turned to the ON position, the passenger airbag ON/OFF indicator will be ON/OFF depending on the conditions listed below.


Front passenger seat condition
Passenger Airbag ON/OFF Indicator
SRS Warning Light
ON Indicator
OFF Indicator
Adult is seated.
ON
OFF
OFF
Child is seated.
OFF
ON
OFF
Vacant
OFF
OFF
OFF
Occupant classification system failure
OFF
ON
ON

INSPECTION PROCEDURE

1.CHECK SRS WARNING LIGHT
  1. Turn the ignition switch to the ON position, and check the SRS warning light condition.

    HINT:
    If this trouble occurs, the SRS warning light is off. If it is on, a DTC is output. Troubleshoot for the output DTC.

    OK:
    After the primary check period, SRS warning light goes off.

    HINT:
    The primary check period is approximately 6 seconds after the ignition switch is turned to the ON position.



NG
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
OK


2.PERFORM ZERO POINT CALIBRATION
  1. Turn the ignition switch to the LOCK position.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the Techstream, perform "Zero point calibration" (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.



NG
Go to step 4
OK


3.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform "Sensitivity check" (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 4
OK

END 

4.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
  1. Turn the ignition switch to the LOCK position.

  1. Loosen the 4 installation bolts of the front seat assembly RH.

  1. Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.

Torque:
37 N*m{ 375 kgf*cm , 27 ft.*lbf }


NEXT


5.PERFORM ZERO POINT CALIBRATION
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the Techstream, perform "Zero point calibration" (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.



NG
Go to step 7
OK


6.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform "Sensitivity check" (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 7
OK

END 

7.CHECK CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check the connectors are properly connected to the occupant classification ECU and the 4 occupant classification sensors.

    OK:
    The connectors are connected.

  1. Disconnect the connectors from the occupant classification ECU and the 4 occupant classification sensors.

  1. Check the connectors are not damaged or deformed.

    OK:
    The connectors are properly normal.



NG
REPAIR OR REPLACE CONNECTOR, THEN GO TO STEP 1
OK


8.CHECK DTC
  1. Connect the connectors to the occupant classification ECU and the 4 occupant classification sensors.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Turn the ignition switch to the LOCK position.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC is not output.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK


9.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).


NEXT


10.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the Techstream, perform "Zero point calibration" (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


11.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform "Sensitivity check" (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

END