Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > TRAC OFF Indicator Light Remains ON

for Preparation Click here


DESCRIPTION

The skid control ECU is connected to the combination meter via CAN and multiplex communications.
When the traction OFF switch is turned on, the TRAC OFF indicator light will come on (for 2WD model).

WIRING DIAGRAM


C159741E02


INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if the CAN communication system DTC is output (Click here).

    Result:

    Result
    Proceed to
    CAN communication system DTC is not output
    A
    CAN communication system DTC is output
    B



B
INSPECT CAN COMMUNICATION SYSTEM
A


2.CHECK MULTIPLEX COMMUNICATION SYSTEM
  1. Check if the multiplex communication system DTC is output (Click here).

    Result:

    Result
    Proceed to
    Multiplex communication system DTC is not output
    A
    Multiplex communication system DTC is output
    B



B
INSPECT MULTIPLEX COMMUNICATION SYSTEM
A


3.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


4.CHECK BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V



NG
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY
OK


5.INSPECT SKID CONTROL ECU (CSW TERMINAL)


    C141673E25
  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Condition
    Switch Condition
    Specified Condition
    S3-43 (CSW) - Body ground
    Traction OFF Switch OFF (Not pressed)
    10 kΩ or higher



NG
Go to step 7
OK


6.INSPECT COMBINATION METER ASSEMBLY
  1. Reconnect the skid control ECU connector.

  1. Perform Active Test of the combination meter (meter CPU) using Techstream (Click here).

    OK:
    The TRAC OFF indicator light turns on or off in accordance with Techstream.

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY
OK

REPLACE BRAKE ACTUATOR ASSEMBLY 

7.INSPECT TRACTION OFF SWITCH


    C156495E01
  1. Disconnect the traction OFF switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (+) - 4 (E)
    Switch is pushed in
    Below 1 Ω
    3 (+) - 4 (E)
    Switch is not pushed in
    10 kΩ or higher



NG
REPLACE TRACTION OFF SWITCH
OK


8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - TRACTION OFF SWITCH)


    C159743E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S3-43 (CSW) - T5-3 (+)
    Always
    Below 1 Ω
    S3-43 (CSW) - Body ground
    Always
    10 kΩ or higher
    T5-4 (E) - Body ground
    Always
    Below 1 Ω

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY