Home › SUSPENSION & AXLE › AXLE › FRONT AXLE HUB

FRONT AXLE HUB > INSTALLATION

for Preparation Click here



1. INSTALL FRONT AXLE ASSEMBLY LH


    C083023
  1. Install the 2 bolts, nuts and front axle assembly LH with the 2 bolts and nuts to the shock absorber assembly front LH.

    Torque:
    230 N*m{ 2,350 kgf*cm , 170 ft.*lbf }

    NOTICE:
    1. Only when reusing the bolts and nuts, apply the small amount of engine oil to the screw part of the nuts.
    2. Do not excessively push out the front axle assembly LH.
    3. Be careful not to damage the outboard joint boot.
    4. Be careful not to damage the speed sensor rotor.



2. INSTALL FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 LH


    F040142
  1. Install the lower ball joint to the front suspension arm sub-assembly lower with the bolt and nuts.

    Torque:
    127 N*m{ 1,300 kgf*cm , 94 ft.*lbf }



3. INSTALL TIE ROD END SUB-ASSEMBLY LH
  1. Install the tie rod end to the steering knuckle with the nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut up to 60° further.



4. INSTALL FRONT DISC


5. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH


    C067088
  1. Install the front disc brake caliper assembly LH with the 2 bolts to the steering knuckle LH.

    Torque:
    104 N*m{ 1,060 kgf*cm , 77 ft.*lbf }



6. INSTALL FRONT AXLE SHAFT LH NUT
  1. Clean the threaded parts on the drive shaft and front axle shaft nut using a non-residue solvent.

    NOTICE:
    1. Be sure to perform this work for a new drive shaft.
    2. Keep the threaded parts free of oil and foreign objects.

  1. Using a socket wrench (30mm), install a new axle hub LH nut.

    Torque:
    294 N*m{ 3,000 kgf*cm , 217 ft.*lbf }



7. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY LH
  1. Remove the 2 bolts and separate the front disc brake caliper assembly LH from the steering knuckle LH.

    NOTICE:
    Use a string or other device to keep the brake caliper from hanging down.



8. REMOVE FRONT DISC


9. INSPECT BEARING BACKLASH


    F040163E03
  1. Using a dial gauge, check for backlash near the center of the axle hub.

    Maximum:
    0.05 mm (0.0020 in.)

    If backlash exceeds the maximum, replace the bearing.

    NOTICE:
    Ensure that the dial gauge is set at right angles to the measurement surface.



10. INSPECT AXLE HUB DEVIATION


    F040164E02
  1. Using a dial gauge, check for deviation in the surface of the axle hub outside the hub bolt.

    Maximum:
    0.05 mm (0.0020 in.)

    If deviation exceeds the maximum, replace the axle hub.

    NOTICE:
    Ensure that the dial gauge is set at right angles to the measurement surface.



11. INSTALL FRONT DISC


12. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH


    C067088
  1. Install the front disc brake caliper assembly LH with the 2 bolts to the steering knuckle LH.

    Torque:
    104 N*m{ 1,060 kgf*cm , 77 ft.*lbf }



13. INSTALL SPEED SENSOR FRONT LH


    F040147
  1. Install the speed sensor to the steering knuckle with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Prevent foreign matter from adhering to the speed sensor.



    C083022
  1. Install the flexible hose and the speed sensor to the shock absorber with the bolt and set the clip of sensor on knuckle.

    Torque:
    19 N*m{ 192 kgf*cm , 14 ft.*lbf }

    NOTICE:
    1. Be careful not to damage the speed sensor.
    2. Prevent foreign matter from adhering to the speed sensor.
    3. Do not twist the sensor wire when installing the speed sensor.



14. INSTALL FRONT AXLE SHAFT LH NUT
  1. Clean the threaded parts on the drive shaft and front axle shaft nut using a non-residue solvent.

    NOTICE:
    1. Be sure to perform this work for a new drive shaft.
    2. Keep the threaded parts free of oil and foreign objects.



    C068609
  1. Using a socket wrench (30 mm), install a new axle hub LH nut.

    Torque:
    294 N*m{ 3,000 kgf*cm , 217 ft.*lbf }

  1. Using a chisel and hammer, stake the axle hub LH nut.



15. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }



16. INSPECT FRONT WHEEL ALIGNMENT
  1. Inspect front wheel alignment (Click here).



17. CHECK ABS SPEED SENSOR SIGNAL
  1. ABS WITH EBD SYSTEM (Click here).

  1. ABS WITH EBD & BA & TRAC & VSC SYSTEM (Click here).