Home › SUSPENSION & AXLE › SUSPENSION › REAR AXLE BEAM

REAR AXLE BEAM > INSTALLATION

for Preparation Click here



1. INSTALL REAR AXLE BEAM DAMPER
  1. Install the rear axle beam damper to the rear axle beam assembly.



2. INSTALL REAR AXLE CARRIER BUSH LH


    G025785E01
  1. Align the matchmarks on the axle beam assembly with the 2 notches of a new bushing and temporarily install the bushing to the rear axle beam assembly.

  1. Using SST, install the bushing to the axle beam.

    SST
    09710-04101  
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04051, 09957-04010, 09958-04011)
    09950-60010   (09951-00620)

    NOTICE:
    1. Hang the claw of SST to the bushing securely.
    2. Do not scratch the rubber portion of the bushing.
    3. Do not deform the bushing rib.



3. INSTALL REAR AXLE CARRIER BUSH RH
SST
09710-04101  
09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04051, 09957-04010, 09958-04011)
09950-60010   (09951-00620)

HINT:
Install the RH side by the same procedures as the LH side.



4. INSTALL REAR BRAKE TUBE FLEXIBLE HOSE


    G025786E01
  1. Install the flexible hose and clip.

  1. Using SST, connect the brake tube to the flexible hose.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

    SST
    09023-00101  

    HINT:
    Install the RH side by the same procedures as the LH side.



5. TEMPORARILY TIGHTEN REAR AXLE BEAM ASSEMBLY
  1. Support the rear axle beam assembly with a jack.

  1. Install the rear axle beam assembly, 2 bolts and temporary tighten the 2 nuts.



6. INSTALL COIL SPRING REAR LH

HINT:
(Click here)



7. INSTALL COIL SPRING REAR RH

HINT:
Install the RH side by the same procedures as the LH side.



8. CONNECT SHOCK ABSORBER ASSEMBLY REAR LH

HINT:
(Click here)



9. CONNECT SHOCK ABSORBER ASSEMBLY REAR RH

HINT:
Connect the RH side by the same procedures as the LH side.



10. INSTALL BRAKE BACKING PLATE SUB-ASSEMBLY REAR LH (for DRUM REAR BRAKE)
  1. Install the 2 rear axle bearing retainer inner LH and parking brake plate sub-assembly LH.



11. INSTALL BRAKE BACKING PLATE SUB-ASSEMBLY REAR RH (for DRUM REAR BRAKE)

HINT:
Install the RH side by the same procedures as the LH side.



12. INSTALL PARKING BRAKE PLATE SUB-ASSEMBLY LH (for DISC REAR BRAKE)
  1. 2WD DRIVE TYPE: Install the 2 rear axle bearing retainer inner LH and parking brake plate sub-assembly LH to the rear axle beam assembly.

  1. 4WD DRIVE TYPE: Install the rear axle bearing retainer outer and parking brake plate sub-assembly LH to the rear axle beam assembly.



13. INSTALL PARKING BRAKE PLATE SUB-ASSEMBLY RH (for DISC REAR BRAKE)

HINT:
Install the RH side by the same procedures as the LH side.



14. INSTALL REAR AXLE HUB & BEARING ASSEMBLY LH (for 2WD)

HINT:
(Click here)



15. INSTALL REAR AXLE HUB & BEARING ASSEMBLY RH (for 2WD)

HINT:
Install the RH side by the same procedures as the LH side.



16. INSTALL REAR AXLE HUB & BEARING ASSEMBLY LH (for 4WD)

HINT:
(Click here)



17. INSTALL REAR AXLE HUB & BEARING ASSEMBLY RH (for 4WD)

HINT:
Install the RH side by the same procedures as the LH side.



18. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for DRUM REAR BRAKE)


19. INSTALL REAR DISC (for DISC REAR BRAKE)


20. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH (for DISC REAR BRAKE)
  1. Install the 2 bolts and rear disc brake caliper assembly LH to the rear axle beam assembly.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



21. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY RH (for DISC REAR BRAKE)

HINT:
Install the RH side by the same procedures as the LH side.



22. CONNECT REAR BRAKE TUBE NO.2

HINT:
(Click here)

SST
09023-00101  


23. CONNECT REAR BRAKE TUBE NO.1
SST
09023-00101  

HINT:
Connect the RH side by the same procedures as the LH side.



24. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.3

HINT:
(Click here)



25. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.2

HINT:
Install the RH side by the same procedures as the LH side.



26. INSTALL DIFFERENTIAL CARRIER ASSEMBLY REAR (for 4WD)

HINT:
(Click here)



27. INSTALL REAR DRIVE SHAFT ASSEMBLY LH (for 4WD)

HINT:
(Click here)



28. INSTALL REAR DRIVE SHAFT ASSEMBLY RH (for 4WD)

HINT:
Install the RH side by the same procedures as the LH side.



29. INSTALL REAR AXLE SHAFT LH NUT (for 4WD)

HINT:
(Click here)



30. INSTALL REAR AXLE SHAFT RH NUT (for 4WD)

HINT:
Install the RH side by the same procedures as the LH side.



31. INSTALL PROPELLER W/CENTER BEARING SHAFT ASSEMBLY (for 4WD)


32. CONNECT SKID CONTROL SENSOR WIRE (for 2WD)

HINT:
(Click here)

HINT:
Connect the RH side by the same procedures as the LH side.



33. INSTALL SPEED SENSOR REAR LH (for 4WD)

HINT:
(Click here)



34. INSTALL SPEED SENSOR REAR RH (for 4WD)

HINT:
Install the RH side by the same procedures as the LH side.



35. INSTALL EXHAUST PIPE ASSEMBLY TAIL

HINT:
  1. 2WD DRIVE TYPE
  2. 4WD DRIVE TYPE



36. BLEED BRAKE LINE

HINT:
(Click here)



37. INSTALL REAR WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }



38. INSPECT BRAKE FLUID LEVEL IN RESERVOIR


39. STABILIZE SUSPENSION

HINT:
(Click here)



40. FULLY TIGHTEN SHOCK ABSORBER ASSEMBLY REAR LH

HINT:
(Click here)



41. FULLY TIGHTEN SHOCK ABSORBER ASSEMBLY REAR RH

HINT:
Fully tighten the RH side by the same procedures as the LH side.



42. FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY

HINT:
(Click here)



43. INSTALL REAR FLOOR NO.2 CROSSMEMBER BRACE LH

HINT:
(Click here)



44. INSTALL REAR FLOOR NO.2 CROSSMEMBER BRACE RH

HINT:
Install the RH side by the same procedures as the LH side.



45. INSTALL FUEL TANK FILLER HOSE COVER

HINT:
(Click here)



46. INSPECT REAR WHEEL ALIGNMENT

HINT:
(Click here)



47. CHECK ABS SPEED SENSOR SIGNAL
  1. ABS WITH EBD SYSTEM (Click here)

  1. ABS WITH EBD & BA & TRAC & VSC SYSTEM (Click here)