Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1794    Open in Occupant Classification ECU Battery Positive Line

for Preparation Click here


DESCRIPTION

This circuit consists of the occupant classification ECU and the power source circuit (battery, fuse, wire harness).
DTC B1794 is recorded when a malfunction is detected in the occupant classification ECU or the power source circuit.

HINT:
When DTC B1794 is output after switching the ignition switch LOCK-ON-LOCK 50 times in a row when a malfunction occurs in the power circuit for the occupant classification system, the DTC is output again when a malfunction is detected even once after being cleared, unless the normal system code is input.

DTC No.
DTC Detecting Condition
Trouble Area
B1794
  1. The ignition switch is turned from LOCK to ON, hold for 10 seconds or more, and back to LOCK again 50 times in a row when a malfunction occurs in the power circuit for the occupant classification system.
  2. Occupant classification ECU malfunction
  1. Battery
  2. ECU-B Fuse
  3. Floor wire No. 2
  4. Front seat wire RH
  5. Occupant classification ECU


WIRING DIAGRAM


H045985E02


INSPECTION PROCEDURE

1.CHECK BATTERY
  1. Measure the voltage of the battery.

    Standard:
    11 to 14 V



NG
REPLACE BATTERY
OK


2.CHECK FUSE
  1. Check the ECU-B fuse.

    Standard:
    Below 1 Ω



NG
REPLACE FUSE
OK


3.CHECK WIRE HARNESS


    H043112E02
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the occupant classification ECU.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester connection
    Condition
    Specified condition
    O3-1 (+B) - Body ground
    Always
    10 to 14 V
    O3-7 (IG) - Body ground
    Ignition switch ON
    10 to 14 V

  1. Turn the ignition switch to the LOCK position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    O3-3 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE WIRE HARNESS
OK


4.CHECK DTC
  1. Turn the ignition switch to the ON position.

  1. Clear the DTCs stored in memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 10 seconds.

  1. Using the Techstream, check the DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1794 is not output.

    HINT:
    Codes other than code B1794 may be output at this time, but they are not related to this check.



NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK 

5.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).


NEXT


6.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the Techstream, perform the "Zero point calibration" (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


7.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the "Sensitivity check" (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

END