Home › BODY › ENGINE HOOD / DOOR › POWER SLIDE DOOR SYSTEM

POWER SLIDE DOOR SYSTEM > Power Slide Door RH does not Operate When Satellite Switch is Pressed

for Preparation Click here


DESCRIPTION

  1. The power slide door operates only when the power slide door main switch is ON (switch free: orange paint on the top of the switch appears). The power slide door ECU RH controls the power slide door RH, which activates the slide door motor to open / close the slide door.
  2. A request signal from the satellite switch for the power slide door RH is input to the the driver side junction block ECU, which then sends this request signal using a BEAN line to the power slide door ECU RH.
  3. A request signal from the power slide door control switch RH is directly input to the power slide door ECU RH.
  4. When the child lock is in the locked condition, the power slide door control switch RH is disabled, thus the power slide door RH is not activated by this switch.
  5. When the touch sensor has an open / short-circuit, closing of the power slide door is disabled.

NOTICE:
When disconnecting the negative (-) terminal cable of the battery or control motor and clutch, initialize the power slide door system (Click here).


WIRING DIAGRAM


B120052E03


B120053E03


INSPECTION PROCEDURE

1.BASIC INSPECTION
  1. Conditions necessary for the power slide door to open:

    1. Power slide door main switch is in the ON position (switch free: orange paint on the top of the switch appears).

    2. Slide door is unlocked (door lock position switch is in the ON position when the slide door is fully closed).

    3. Shift lever is in the P position when the ignition switch is ON (When the ignition switch is OFF, the power slide door operates at any position of the shift lever.)

  1. Conditions necessary for the power slide door to close:

    1. Power slide door main switch is in the ON position (switch free: orange paint on the top of the switch appears).

    2. Slide door is between approximately the half-open position and the fully open position.

    3. Slide door touch sensor is not damaged and deformed.


OK


2.INSPECT FUSE (ECU-B)
  1. Inspect the ECU-B fuse.



NG
REPLACE FUSE
OK


3.CHECK DTC
  1. Check for DTC B2223. DTC B2223 indicates a pulse sensor malfunction.

    1. Without code outputs, proceed to A.

    2. With code outputs, proceed to B.



B
GO TO DTC B2223
A


4.INSPECT COMMUNICATION FUNCTION OF LARGE-SCALE MULTIPLEX COMMUNICATION SYSTEM (BEAN)
  1. Use the Techstream to check for normal function of the multiplex communication system.

    1. (ECU unconnected, communication line malfunctioning) Without DTC B1214, B1215 or B1216 outputs, proceed to A.

    2. (ECU unconnected, communication line malfunctioning) With DTC B1214, B1215 or B1216 outputs, proceed to B.



B
GO TO MULTIPLEX COMMUNICATION SYSTEM
A


5.READ VALUE USING TECHSTREAM
  1. Using the Techstream, check the DATA LIST for proper functioning of the power slide door main switch.

    OK (Power slide door ECU RH): 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    PSD Main Switch
    Power slide door main SW
    / ON or OFF
    ON: Orange paint on top of the switch appears
    OFF: Orange paint on top of the switch does not appear
    -



OK
Go to step 8
NG


6.INSPECT POWER SLIDE DOOR MAIN SWITCH


    B068896E01
  1. Inspect the resistance of the main switch.

    Resistance:
    Terminal No.
    Condition
    Specified Condition
    4 - 5
    Free (ON)
    Below 1 Ω
    Pushed (OFF)
    10 kΩ or higher

    HINT:
    If the switch does not illuminate, it will not affect the ON / OFF function of the switch. For the illumination check, refer to SLIDE DOOR SYSTEM (Click here).



NG
REPLACE POWER SLIDE DOOR MAIN SWITCH
OK


7.CHECK WIRE HARNESS (POWER SLIDE DOOR MAIN SWITCH - POWER SLIDE DOOR ECU RH)


    B068444E02
  1. Disconnect the P10 switch and P27 ECU connectors.

  1. Check the resistance between the wire harness side connectors.

    Resistance (Check for open circuit):
    Terminal No.
    Specified Condition
    P10-4 - P27-6 (MSW)
    Below 1 Ω
    P10-5 - P27-5 (MSE)

  1. Check the resistance between the P10 switch connector and body ground.

    Resistance (Check for short circuit):
    Terminal No.
    Specified Condition
    P10-4 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE POWER SLIDE DOOR ECU RH 

8.CHECK SWITCH OPERATION
  1. If the power slide door does not respond to using the satellite switch, proceed to A.

  1. If the power slide door does not respond to using the power slide door control switch (child lock is set at UNLOCK.), proceed to B.

    HINT:
    If the power slide door cannot operate using the power slide door control switch even when the child lock is locked, there may be a malfunction in the child lock switch. In this case, check the handle switch circuit (Click here).



B
Go to step 11
A


9.INSPECT SATELLITE SWITCH


    B068442E03
  1. Check the resistance of the RH switch.

    Resistance:
    Terminal No.
    Condition
    Specified Condition
    4 - 5
    Free
    10 kΩ or higher
    Pushed
    Below 1 Ω

    HINT:
    If the switch does not illuminate, it will not affect the ON / OFF function of the switch. For the illumination check, refer to SLIDE DOOR SYSTEM (Click here).



NG
REPLACE SATELLITE SWITCH
OK


10.CHECK WIRE HARNESS (SATELLITE SWITCH - DRIVER SIDE J/B, BODY GROUND)


    B068899E04
  1. Disconnect the S13 switch and B7 ECU connectors.

  1. Check the resistance between the wire harness side connectors.

    Resistance (Check for open circuit):
    Terminal No.
    Specified Condition
    S13-4 (R) - B7-7 (PSDS)
    Below 1 Ω

  1. Check the resistance between the S13 switch connector and body ground.

    Resistance (Check for open circuit):
    Terminal No.
    Specified Condition
    S13-5 (GND) - Body ground
    Below 1 Ω



OK
Go to step 14
NG

REPAIR OR REPLACE HARNESS AND CONNECTOR 

11.READ VALUE USING TECHSTREAM
  1. Using the Techstream, check the DATA LIST for proper functioning of the power slide door control switch RH.

    OK (Power slide door ECU RH): 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    B Pillar Switch*
    Power slide door control switch* signal
    / ON or OFF
    ON: Power slide door control switch* is pushed
    OFF: Power slide door control switch* is not pushed
    -
    * "B Pillar Switch" appears on the display of the Techstream, however the name of the part corresponding to the display of the tester is "Power slide door control switch".



OK
Go to step 14
NG


12.INSPECT POWER SLIDE DOOR CONTROL SWITCH RH


    B067766E01
  1. Inspect the resistance of the switch.

    Resistance:
    Terminal No.
    Condition
    Specified Condition
    1 - 5
    Free
    10 kΩ or higher
    Pushed
    Below 1 Ω

    HINT:
    If the switch does not illuminate, it will not affect the ON / OFF function of the switch. For the illumination check, refer to SLIDE DOOR SYSTEM (Click here).



NG
REPLACE POWER SLIDE DOOR CONTROL SWITCH RH
OK


13.CHECK WIRE HARNESS (POWER SLIDE DOOR CONTROL SWITCH RH - POWER SLIDE DOOR ECU RH)


    B068445E02
  1. Disconnect the P24 switch and P27 ECU connectors.

  1. Check the resistance between the wire harness side connectors.

    Resistance (Check for open circuit):
    Terminal No.
    Specified Condition
    P24-5 - P27-4 (CSW)
    Below 1 Ω

  1. Check the resistance between the P24 switch connector and body ground.

    Resistance (Check for open circuit):
    Terminal No.
    Specified Condition
    P24-1 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE POWER SLIDE DOOR ECU RH 

14.READ VALUE USING TECHSTREAM
  1. Using the Techstream, check the DATA LIST for proper functioning of the power slide door touch sensor RH.

    OK (Power slide door ECU RH): 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    PSD Touch Sensor
    Power slide door touch sensor
    / OFF, ON or OPEN
    OFF: Power slide door touch sensor is free
    ON: Power slide door touch sensor is pressed
    OPEN: Power slide door touch sensor is opened
    -



OK
Go to step 17
NG


15.INSPECT POWER SLIDE DOOR TOUCH SENSOR RH


    B068908E01
  1. Check the resistance of the sensor.

    Resistance:
    Terminal No.
    Condition
    Specified Condition
    1 - 2
    Free
    Approx. 1 kΩ
    Pressed
    Less than 100 Ω



NG
REPLACE POWER SLIDE DOOR TOUCH SENSOR RH
OK


16.CHECK WIRE HARNESS (POWER SLIDE DOOR TOUCH SENSOR RH - POWER SLIDE DOOR ECU RH)


    B068446E02
  1. Disconnect the P32 sensor and P27 ECU connectors.

  1. Check the resistance between the wire harness side connectors.

    Resistance (Check for open circuit):
    Terminal No.
    Specified Condition
    P32-1 - P27-16 (OS)
    Below 1 Ω
    P32-2 - P27-15 (OSG)



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE POWER SLIDE DOOR ECU RH 

17.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Select the ACTIVE TEST and then check that the power slide door control motor and clutch RH operates.

    HINT:
    During the ACTIVE TEST, the Techstream sends a signal to the power slide door ECU RH to drive the motor and clutch. If the motor and clutch operates, the motor and clutch itself and the wire harness between the motor and clutch and the power slide door ECU RH are considered to be functioning normally.


    OK (Power slide door ECU RH): 
    Item
    Test Details
    Diagnostic Note
    PSD Motor
    Power slide door control motor is in operation
    OFF / FORWARD / REVERAE
    Clutch is OFF while power slide door motor is operating
    PSD Clutch
    Power slide door control clutch is release
    OFF / ON
    Power slide door motor is OFF when clutch is ON



OK
Go to step 20
NG


18.INSPECT SLIDE DOOR CONTROL MOTOR AND CLUTCH ASSEMBLY RH


    B068463E01
  1. Remove the motor and clutch.

  1. Connect the battery positive (+) lead to terminal 3 and battery negative (-) terminal lead to terminal 2.

  1. Apply battery voltage to the terminals and check the motor operation.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 8
    Battery negative (-) → Terminal 7
    Open
    Battery positive (+) → Terminal 7
    Battery negative (-) → Terminal 8
    Close

  1. Check the resistance of the clutch terminals.

    Resistance:
    Terminal No.
    Specified Condition
    2 - 3
    4.0 Ω
    6 - Body ground
    Below 1 Ω

  1. Reinstall the motor and clutch with the connector connected.



    B068909E04
  1. Check the pulse of the pulse sensor.

    1. Using an oscilloscope, check the pulse generated when the door is manually opened and closed.

      Reference:
      Terminal
      Tool setting
      Vehicle condition
      5 - 9, 9 - 10
      10 V/DIV., 10 ms/DIV.
      Door moving

      HINT:
      A cycle of the pulse changes between approx. 10 to 20 msec. according to the speeds that the slide door is moving.

      NOTICE:
      When disconnecting the control motor and clutch, initialize the power slide door system (Click here).



NG
REPLACE SLIDE DOOR CONTROL MOTOR AND CLUTCH ASSEMBLY RH
OK


19.CHECK WIRE HARNESS (POWER SLIDE DOOR CONTROL MOTOR - POWER SLIDE DOOR ECU RH)


    B068440E02
  1. Disconnect the P22 motor and clutch, the P27 and P28 ECU connectors.

  1. Check the resistance between the wire harness side connectors.

    Resistance (Check for open circuit):
    Terminal No.
    Specified Condition
    P22-9 - P27-23 (DSG)
    Below 1 Ω
    P22-4 - P27-26 (DSV)
    P22-10 - P27-25 (DS1)
    P22-5 - P27-24 (DS2)
    P22-3 - P28-7 (CL+)
    P22-2 - P28-6 (CL-)
    P22-7 - P28-1 (SD+)
    P22-8 - P28-3 (SD-)



NG
REPAIR OR REPLACE WIRE HARNESS AND CONNECTOR
OK

REPLACE POWER SLIDE DOOR ECU RH 

20.READ VALUE USING TECHSTREAM
  1. Using the Techstream, check the DATA LIST for proper functioning of the switches listed below.

    OK (Power slide door ECU RH): 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    Pole* Switch
    Power slide door lock pawl* position switch signal
    / ON or OFF
    ON: Slide door is unlatched
    OFF: Slide door is latched
    -
    Half Switch
    Power slide door lock half latch switch signal
    / ON or OFF
    ON: Slide door is not completely closed
    OFF: Slide door is closed
    -
    Full Switch
    Power slide door lock full latch switch signal
    / ON or OFF
    ON: Slide door is open
    OFF: Slide door is closed
    -
    Closer Position Switch
    Power slide door lock closer position switch signal
    / ON or OFF
    ON: Closer is not in the initial position and inside / outside handle is not pulled
    OFF: Closer is in the initial position and inside / outside handle is pulled
    -
    * "Pole" appears on the display of the Techstream, however the name of the part corresponding to the display of the tester is "pawl".



OK
Go to step 23
NG


21.INSPECT POWER SLIDE DOOR LOCK ASSEMBLY RH


NG
REPLACE POWER SLIDE DOOR LOCK ASSEMBLY RH
OK


22.CHECK WIRE HARNESS (POWER SLIDE DOOR LOCK ASSEMBLY RH - POWER SLIDE DOOR ECU RH)


NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE POWER SLIDE DOOR ECU RH 

23.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Select the ACTIVE TEST and then check that the slide door lock release motor RH operates.

    HINT:
    During the ACTIVE TEST, the Techstream sends a signal to the power slide door ECU RH to drive the release motor. If the release motor operates, the release motor itself and the wire harness between the release motor and power slide ECU RH are considered to be functioning normally.


    OK (Power slide door ECU RH): 
    Item
    Test Details
    Diagnostic Note
    Release Actuator
    Slide door lock release motor is release
    OFF / ON
    -



OK
Go to step 26
NG


24.INSPECT SLIDE DOOR LOCK RELEASE MOTOR ASSEMBLY


    B068467E01
  1. Apply battery voltage and inspect operation of the release motor.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 2
    Battery negative (-) → Terminal 1
    Release operation
    No battery voltage is applied
    Original position



NG
REPLACE SLIDE DOOR LOCK RELEASE MOTOR ASSEMBLY
OK


25.CHECK WIRE HARNESS (SLIDE DOOR LOCK RELEASE MOTOR - POWER SLIDE DOOR ECU RH)


    B068448E02
  1. Disconnect the S24 motor and P28 ECU connectors.

  1. Check the resistance between the wire harness side connectors.

    Resistance (Check for open circuit):
    Terminal No.
    Specified Condition
    S24-2 - P28-5 (RACT)
    Below 1 Ω

  1. Check the resistance between the S22 motor connector and body ground.

    Resistance (Check for open circuit):
    Terminal No.
    Specified Condition
    S24-1 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


26.REPLACE POWER SLIDE DOOR ECU RH
  1. Check the power slide door for normal OPEN / CLOSE operation.



NG
REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY (MULTIPLEX NETWORK BODY ECU)
OK

SYSTEM NORMAL