Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0128    Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)

for Preparation Click here

HINT:
This DTC relates to the thermostat.


DESCRIPTION

This DTC is set when the Engine Coolant Temperature (ECT) does not reach 75°C (167°F) despite sufficient engine warm-up time.

DTC No.
DTC Detection Condition
Trouble Area
P0128
Conditions (a), (b) and (c) are met for 5 seconds (2 trip detection logic):
(a) Cold start
(b) Engine warmed up
(c) ECT less than 75°C (167°F)
  1. Thermostat
  2. Cooling system
  3. ECT sensor
  4. ECM

MONITOR DESCRIPTION


A082385E11

The ECM estimates the ECT based on the starting temperature, engine loads, and engine speeds. The ECM then compares the estimated temperature with the actual ECT. When the estimated ECT reaches 75°C (167°F), the ECM checks the actual ECT. If the actual ECT is less than 75°C (167°F), the ECM interprets this as a malfunction in the thermostat or the engine cooling system and sets the DTC.

MONITOR STRATEGY


Related DTCs
P0128: Coolant Thermostat
Required Sensors / Components (Main)
Thermostat
Required Sensors / Components (Related)
Engine Coolant Temperature (ECT) sensor, Intake Air Temperature (IAT) sensor, Vehicle speed sensor
Frequency of Operation
Once per driving cycle
Duration
460 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not present
P0010, P0020 (OCV bank 1, 2)
P0011, P0021 (VVT system bank 1, 2 - advance)
P0012, P0022 (VVT system bank 1, 2 - retard)
P0013, P0023 (Exhaust OCV bank 1, 2)
P0014, P0024 (Exhaust VVT system bank 1, 2 - advance)
P0015, P0025 (Exhaust VVT system bank 1, 2 - retard)
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment)
P0031, P0032, P0051, P0052 (A/F sensor heater)
P0100, P0102, P0103 (MAF meter)
P0110, P0112, P0113 (IAT sensor)
P0115, P0117, P0118 (ECT sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (TP sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0301, P0302, P0303, P0304, P0305, P0306 (Misfire)
P0335 (CKP sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0500 (Vehicle speed sensor)
P2195, P2196, P2197, P2198 (A/F sensor - rationality)
P2237, P2240 (A/F sensor - open)
P2238, P2241, P2252, P2255 (A/F sensor - low impedance)
P2239, P2242, P2253, P2256 (A/F sensor - high impedance)
P2A00, P2A03 (A/F sensor - slow response)
Battery voltage
11 V or more
Either of following conditions is met:
Condition 1 or 2
1. All of following conditions are met:
Conditions (a), (b) and (c)
(a) ECT at engine start - IAT at engine start
-15 to 7°C (5 to 45°F)
(b) ECT at engine start
-10 to 56°C (14 to 133°F)
(c) IAT at engine start
-10 to 56°C (14 to 133°F)
2. All of following conditions are met:
Conditions (d), (e) and (f)
(d) ECT at engine start - IAT at engine start
More than 7°C (45°F)
(e) ECT at engine start
56°C (133°F) or less
(f) IAT at engine start
-10°C (14°F) or more
Accumulated time that vehicle speed is 80 mph (128 km/h) or more
Less than 20 seconds

TYPICAL MALFUNCTION THRESHOLDS


Duration that all of the following conditions 1 and 2 are met
5 seconds or more
1. Estimated ECT
75°C (167°F) or more
2. ECT sensor output
Less than 75°C (167°F)

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0128)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0128
    A
    P0128 and other DTCs
    B

    HINT:
    If any DTCs other than P0128 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK COOLING SYSTEM
  1. Check for defects in the cooling system that might cause the system to be too cold, such as abnormal radiator fan operation or any modifications.



NG
REPAIR OR REPLACE COOLING SYSTEM
OK


3.INSPECT THERMOSTAT
  1. Remove the thermostat (Click here).

  1. Check the valve opening temperature of the thermostat (Click here).

    Standard:
    80 to 84°C (176 to 183°F)

    HINT:
    In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.

  1. Reinstall the thermostat (Click here).



NG
REPLACE THERMOSTAT (Click here)
OK

REPLACE ECM (Click here)