Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2237    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

DTC    P2238    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)

DTC    P2239    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)

DTC    P2240    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1)

DTC    P2241    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1)

DTC    P2242    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1)

DTC    P2252    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)

DTC    P2253    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)

DTC    P2255    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1)

DTC    P2256    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1)

for Preparation Click here

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


DESCRIPTION

Refer to DTC P2195 .

DTC No.
DTC Detection Condition
Trouble Area
P2237
P2240
Open in the circuit between terminals A1A+ and A1A-/A2A+ and A2A- the air fuel ratio sensor while engine running.
(2 trip detection logic)
  1. Open or short in A/F sensor (bank 1, 2 sensor 1)
  2. A/F sensor (bank 1, 2 sensor 1)
  3. ECM
P2238
P2241
  1. Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic):
    (a) Voltage at terminal A1A+/A2A+ is 0.5 V or less.
    (b) Voltage difference between terminals A1A+ and A1A-/A2A+ and A2A- is 0.1 V or less.
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. A/F sensor heater (bank 1, 2 sensor 1)
  4. A/F sensor heater relay
  5. A/F sensor heater and relay circuits
  6. ECM
P2239
P2242
A1A+/A2A+ voltage is more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. A/F sensor heater
  4. A/F sensor heater relay
  5. A/F sensor heater and relay circuits
  6. ECM
P2252
P2255
A1A-/A2A- voltage is 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. A/F sensor heater
  4. A/F sensor heater relay
  5. A/F sensor heater and relay circuits
  6. ECM
P2253
P2256
A1A-/A2A- voltage is more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. A/F sensor heater
  4. A/F sensor heater relay
  5. A/F sensor heater and relay circuits
  6. ECM

HINT:
  1. DTC P2237, P2238, P2239, P2252 and P2253 indicate malfunctions related to the bank 1 A/F sensor circuit.
  2. DTC P2240, P2241, P2242, P2255 and P2256 indicate malfunctions related to the bank 2 A/F sensor circuit.
  3. Bank 1 refers to the bank that includes cylinder No. 1.
  4. Bank 2 refers to the bank that includes cylinder No. 2.


MONITOR DESCRIPTION

The Air-Fuel Ratio (A/F) sensor varies its output voltage in proportion to the air-fuel ratio. If the A/F sensor impedance (alternating current resistance) or voltage output deviates greatly from the standard range, the ECM determines that there is an open or short malfunction in the A/F sensor circuit.

MONITOR STRATEGY


Related DTCs
P2237: Air fuel ratio sensor (Bank 1) open circuit between A1A+ and A1A-
P2238: Air fuel ratio sensor (Bank 1) short circuit between A1A+ and A1A-
P2238: Air fuel ratio sensor (Bank 1) short circuit between A1A+ and GND
P2239: Air fuel ratio sensor (Bank 1) short circuit between A1A+ and +B
P2240: Air fuel ratio sensor (Bank 2) open circuit between A2A+ and A2A-
P2241: Air fuel ratio sensor (Bank 2) short circuit between A2A+ and A2A-
P2241: Air fuel ratio sensor (Bank 2) short circuit between A2A+ and GND
P2242: Air fuel ratio sensor (Bank 2) short circuit between A2A+ and +B
P2252: Air fuel ratio sensor (Bank 1) short circuit between A1A- and GND
P2253: Air fuel ratio sensor (Bank 1) short circuit between A1A- and +B
P2255: Air fuel ratio sensor (Bank 2) short circuit between A2A- and GND
P2256: Air fuel ratio sensor (Bank 2) short circuit between A2A- and +B
Required Sensors / Components (Main)
A/F sensor
Required Sensors / Components (Related)
Engine Coolant Temperature (ECT) sensor, Crankshaft position sensor
Frequency of Operation
Once per driving cycle
Duration
P2238 and P2241 (open circuit between AF+ and AF-): 10 seconds
Others: 5 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not present
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment)
P0031, P0032, P0051, P0052 (A/F sensor heater)
P0100, P0102, P0103 (MAF meter)
P0110, P0112, P0113 (IAT sensor)
P0115, P0117, P0118 (ECT sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (TP sensor)
P0125 (Insufficient ECT for closed loop)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel system)
P0301, P0302, P0303, P0304, P0305, P0306 (Misfire)
P0335 (CKP sensor)
P0450, P0451, P0452, P0453 (EVAP system)
P0500 (Vehicle speed sensor)
P0505 (Idle speed control)

P2237 and P2240 (A/F sensor open circuit between A1A+ and A1A-/A2A+ and A2A-): 
Estimated sensor temperature
450 to 550°C (842 to 1022°F)
Engine
Running
Battery voltage
11 V or more

P2238 and P2241 (A/F sensor - Lowimpedance): 
Estimated sensor temperature
700 to 800°C (1292 to 1472°F)
ECT
5°C (41°F) or more
Fuel cut
Not executed

Others: 
Battery voltage
11 V or more
Ignition switch
ON
Time after ignition switch is OFF to ON
5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


P2237 and P2240 (Open circuit between A1A+ and A1A-/A2A+ and A2A-): 
A/F sensor admittance
Below 0.002 1/Ω

P2238 and P2241 (Lowimpedance): 
A/F sensor admittance
Below 0.015 1/Ω

P2238 and P2241 (Short circuit between A1A+ and GND/A2A+ and GND): 
A1A+/A2A+ terminal voltage
0.5 V or less

P2238 and P2241 (Short circuit between A1A+ and A1A-/A2A+ and A2A-): 
Difference between A1A+ and A1A-/A2A+ and A2A- terminal voltage
0.1 V or less

P2239 and P2242 (Short circuit between A1A+ and +B/A2A+ and +B): 
A1A+/A2A+ terminal voltage
More than 4.5 V

P2252 and P2255 (Short circuit between A1A- and GND/A2A- and GND): 
A1A-/A2A- terminal voltage
0.5 V or less

P2253 and P2256 (Short circuit between A1A- and +B/A2A- and +B): 
A1A-/A2A- terminal voltage
More than 4.5 V

WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
For use of the Techstream only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.

  1. The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the Techstream.
    1. Connect the Techstream to the DLC3.
    2. Start the engine and turn the tester on.
    3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
    4. Select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
    5. Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
    6. Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.

      HINT:
      1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
      2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


      Standard voltage:

      Tester Display (Sensor)
      Injection Volumes
      Status
      Voltages
      AFS B1S1 or AFS B2S1 (A/F)
      +25%
      Rich
      Less than 3.1
      AFS B1S1 or AFS B2S1 (A/F)
      -12.5%
      Lean
      More than 3.5
      O2S B1S2 or O2S B2S2 (HO2)
      +25%
      Rich
      More than 0.55
      O2S B1S2 or O2S B2S2 (HO2)
      -12.5%
      Lean
      Less than 0.4

      NOTICE:
      The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.


      Case
      A/F Sensor (Sensor 1)
      Output Voltage
      HO2 Sensor (Sensor 2)
      Output Voltage
      Main Suspected Trouble Area
      1
      A162605E07
      A162598E02
      -
      2
      A162596E01
      A162598E02
      1. A/F sensor
      2. A/F sensor heater
      3. A/F sensor circuit
      3
      A162605E07
      A162596E01
      1. HO2 sensor
      2. HO2 sensor heater
      3. HO2 sensor circuit
      4
      A162596E01
      A162596E01
      1. Fuel pressure
      2. Gas leakage from exhaust system
        (Air-fuel ratio extremely lean or rich)
    1. Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
    2. To display the graph, select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS B1 S1 or AFS B2 S1 and O2S B1 S2 or O2S B2 S2 then press the graph button on the Data List view.

      HINT:
      1. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
      2. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
      3. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)


    A126269E48
  1. Disconnect the A5 or A6 A/F sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    HT (1) - +B (2)
    20°C (68°F)
    1.8 to 3.4 Ω
    HT (1) - AF- (4)
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    HT (1) - +B (2)
    20°C (68°F)
    1.8 to 3.4 Ω
    HT (1) - AF- (4)
    Always
    10 kΩ or higher

  1. Reconnect the A/F sensor connector.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2WD model)
    B
    NG (for 4WD model)
    C



B
REPLACE AIR FUEL RATIO SENSOR (Click here)

C
REPLACE AIR FUEL RATIO SENSOR (Click here)
A


2.INSPECT RELAY (A/F RELAY)


    B016200
  1. Remove the A/F relay from the No. 6 engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage applied to terminals 1 and 2)

  1. Reinstall the A/F relay.



NG
REPLACE RELAY (A/F RELAY)
OK


3.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)


    A136175E10
  1. Disconnect the A5 or A6 A/F sensor connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    +B (A5-2) - Body ground
    9 to 14 V
    +B (A6-2) - Body ground
    9 to 14 V

  1. Turn the ignition switch off.

  1. Disconnect the E10 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance :
    Check for open:
    Tester Connection
    Specified Condition
    HT (A5-1) - HA1A (E10-2)
    Below 1 Ω
    AF+ (A5-3) - A1A+ (E10-22)
    Below 1 Ω
    AF- (A5-4) - A1A- (E10-30)
    Below 1 Ω
    HT (A6-1) - HA2A (E10-1)
    Below 1 Ω
    AF+ (A6-3) - A2A+ (E10-23)
    Below 1 Ω
    AF- (A6-4) - A2A- (E10-31)
    Below 1 Ω
    Check for short:
    Tester Connection
    Specified Condition
    HT (A5-1) or HA1A (E10-2) - Body ground
    10 kΩ or higher
    AF+ (A5-3) or A1A+ (E10-22) - Body ground
    10 kΩ or higher
    AF- (A5-4) or A1A- (E10-30) - Body ground
    10 kΩ or higher
    HT (A6-1) or HA2A (E10-1) - Body ground
    10 kΩ or higher
    AF+ (A6-3) or A2A+ (E10-23) - Body ground
    10 kΩ or higher
    AF- (A6-4) or A2A- (E10-31) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.



  1. Reconnect the A/F sensor connector.


    A165205E01



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (A/F SENSOR - ECM)
OK

REPLACE ECM (Click here)