Home › Brake › BRAKE (REAR) › REAR BRAKE
RM3650E _54 Brake _079883 BRAKE (REAR) _0387572 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·

Vehicle may slip off the vehicle hoist if the vehicle hoist is handled incorrectly.

Danger! Life-threatening injuries!

-

Observe safety information on raising the vehicle using a vehicle hoist.


·

Effects on other persons.

Danger of injury! Risk of damage!

-

Make sure that no other persons are in or around the vehicle.




NOTICE:
·

General information on changing the brake pads:

-

For vehicles older than 48 months it is recommended to replace the retaining spring or expanding spring.

-

The pad wear indicator wire RH must be replaced once it has been removed because the pad wear indicator wire RH loses its retention capability in the brake pad.


·

A CBS reset must be done after every brake pad exchange:

-

A CBS reset in the vehicle is possible in the event of a partially ground down pad wear indicator wire RH. The CBS display in the multi-display is active.

-

In the event of a pad wear indicator wire RH that is not partially ground down, a CBS reset is only possible with the diagnosis system. No CBS display in the multi-display.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>CONDITION BASED SERVICE (CBS)


·

During work on the rear brake, it must be ensured that the button for the electromechanical parking brake cannot be pressed.

·

When exchanging brake pads, reset the CBS display in accordance with factory specification (CBS reset).

·

Carry out test braking while driving at low speed because the effectiveness of the brakes may be reduced during the initial braking operations.

·

Exaggerated emergency and continuous braking operations for faster bedding-in are not permitted.

·

Advise the customer not to perform intentional emergency braking operations for the first 200 km (124 mile) after the brakes have been replaced.



HINT:
·

The following procedure is for the LH side.

·

Use the same procedure for the RH side and LH side.



PROCEDURE

Hide 1.PERFORM REAR BRAKE PAD REPLACEMENT MODE

a.

Connect the diagnosis system with the vehicle.


b.

Determine the workshop mode.

Vehicle management / Service functions / Chassis / Parking brake / Workshop mode


c.

Disconnect the diagnosis system from the vehicle.


Hide 2.REMOVE REAR WHEEL

Hide 3. MEASURE MINIMUM BRAKE DISC THICKNESS (REAR BRAKE)

a.
C413310

Place the special tool 0 495 451 (34 1 280) at three measuring points in area (1) and measure.

SST
09700-WA090  


b.

Compare the measuring results and compare the lowest value with the setpoint value.

HINT:

New rear disc brake pads must only be installed if the rear disc thickness is greater than the minimum rear disc thickness.


Minimum brake disc thickness:
Nominal dimension 330x20:

18.4 mm (0.724 in.)

Nominal dimension 345x24:

22.4 mm (0.882 in.)



Hide 4.REMOVE PAD WEAR INDICATOR WIRE RH (for RH Side)

Hide 5.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C413341

Release the 15 mm bolts (1), if necessary use the hexagon head (2) for counter support.


b.

Remove rear disc brake cylinder assembly (3).


c.
C413620

Remove the rear flexible hose (1) from the bracket (2).


d.

Detach rear flexible hose (1) from rear disc brake cylinder assembly.


Hide 6.REMOVE REAR DISC BRAKE PAD

a.
C413342

Remove the rear disc brake pads (1) from the rear disc brake cylinder mounting in direction of the arrows.


b.

Mark any worn brake pads.

HINT:

If the rear disc brake pad wear exists on one side, they must not be mixed up.



c.
C413343

Remove the rear disc brake pad support plates (1).


d.
C420420N01
0.927,0.656 1.385,0.854 0.458,0.198 10 false SST 2.083,0.208 2.542,0.406 0.458,0.198 10 false SST

Press back the brake piston using the SST.

SST
09719-12010  

NOTICE:
·

When pressing the brake piston back, note the brake fluid level in the brake master cylinder reservoir assembly.

·

Overflowing brake fluid will damage the paintwork.




Hide 7.REMOVE REAR DISC

a.
C413587

Release the E16 bolts (1) and remove the rear disc brake cylinder mounting (2).


b.
C413588

Release the 5 mm hexagon bolt (1) and remove the rear disc (2).

NOTICE:
·

Note the following for the removal of the rear disc:

-

Do not under any circumstances strike the friction ring with a hammer or similar tool.

-

If necessary, carefully tap with a rubber mallet against the rear disc chamber.