1.ADJUST COMPRESSOR OIL (for Type A)
A new compressor with pulley assembly is filled with compressor oil at the factory. The amount of compressor oil in a new compressor with pulley assembly corresponds to the amount of compressor oil for the entire new and unfilled refrigerant circuit.
When the compressor with pulley assembly is replaced, it is essential to adapt the amount of compressor oil.
The following procedure only applies when a new compressor with pulley assembly has a label with the amount of compressor oil.
The compressor oil amount specification is located on the label on the compressor with pulley assembly.
The position of the label can vary depending on the compressor with pulley assembly.
The compressor oil specification on the label is in g, ml or cc. The cc are specified throughout these repair instructions for adjusting the amount of compressor oil, as g and ml closely correspond to cc.
Step 1
Read and record amount of compressor oil specified on the previous compressor with pulley assembly.
If no label is present, continue with step 3, case 1.
Read and record amount of compressor oil specified on a new compressor with pulley assembly.
Compare both amounts of compressor oil with each other.
Amount of compressor oil specified on the previous and a new compressor with pulley assembly is same. In this case, continue with step 3, case 1.
Amount of compressor oil specified on the previous and a new compressor with pulley assembly is not the same.
Amount of compressor oil specified on the previous compressor with pulley assembly is higher than on a new compressor with pulley assembly. Difference is not taken into account. In this case, continue with step 3, case 1.
Amount of compressor oil specified on the previous compressor with pulley assembly is lower than on a new compressor with pulley assembly: Generate and record the difference between both amounts of compressor oil. Then, continue with step 3, case 2.
Example:
Amount of compressor oil specified on the previous compressor with pulley assembly 110 g (3.88 oz).
Amount of compressor oil specified on a new compressor with pulley assembly 150 g (5.29 oz).
150 g (5.29 oz) - 110 g (3.88 oz) = 40 g (1.41 oz) approximately 40 cc (1.35 fl.oz).
Record the difference 40 cc (1.35 fl.oz).
Step 2
Open the oil filler plug.
Transfer all of the compressor oil remaining in the previous compressor with pulley assembly into a measuring cup via the oil filler plug.
Turn the belt pulley during draining.
Step 3
Read the drained amount of compressor oil from the previous compressor with pulley assembly on the measuring cup.
Case 1:
Add 10 cc (0.338 fl.oz) extra to the amount of compressor oil read as a precautionary allowance.
Record at least but a total of 50 cc (1.69 fl.oz).
Example:
20 cc (0.676 fl.oz) read at measuring cup.
20 cc (0.676 fl.oz) + 10 cc (0.338 fl.oz) precautionary allowance = 30 cc (1.01 fl.oz) (below 50 cc (1.69 fl.oz)).
Amount of compressor oil determined for a new compressor with pulley assembly = 50 cc (1.69 fl.oz).
Case 2:
Add 10 cc (0.338 fl.oz) extra to the amount of compressor oil read as a precautionary allowance.
To this add the difference.
Record at least but a total of 50 cc (1.69 fl.oz).
Example:
Difference = 40 cc (1.35 fl.oz).
20 cc (0.676 fl.oz) read at measuring cup.
20 cc (0.676 fl.oz) + 10 cc (0.338 fl.oz) precautionary allowance = 30 cc (1.01 fl.oz).
30 cc (1.01 fl.oz) + 40 cc (1.35 fl.oz) difference = 70 cc (2.37 fl.oz) (above 50 cc (1.69 fl.oz)).
Amount of compressor oil determined for a new compressor with pulley assembly = 70 cc (2.37 fl.oz).
Step 4
Open the oil filler plug.
Drain the following amount of compressor oil from a new compressor with pulley assembly into a clean measuring cup.
Amount of compressor oil to be drained from a new compressor with pulley assembly = amount of compressor oil on the label for a new compressor with pulley assembly - amount of compressor oil determined for a new compressor with pulley assembly.
Example:
Amount on a new compressor with pulley assembly compressor oil label: 150 cc (5.07 fl.oz).
Amount of compressor oil determined for a new compressor with pulley assembly: 50 cc (1.69 fl.oz).
Amount of compressor oil to be drained = 150 cc (5.07 fl.oz) - 50 cc (1.69 fl.oz) = 100 cc (3.38 fl.oz).
100 cc (3.38 fl.oz) must be drained from a new compressor with pulley assembly.
Replace the sealing ring.
Tighten oil filler plug.
Immediately after draining, the remaining compressor oil must be filled into the refrigerant recovery unit expansion tank.
The remaining compressor oil must be disposed of correctly if it is not immediately filled into the expansion tank of the refrigerant recovery unit.
Compressor oil drained from the previous compressor with pulley assembly must not be reused and must be disposed of correctly.
2.ADJUST COMPRESSOR OIL (for Type B)
A new compressor with pulley assembly is filled with compressor oil at the factory. The amount of compressor oil in a new compressor with pulley assembly corresponds to the amount of compressor oil for the entire new and unfilled refrigerant circuit.
When the compressor with pulley assembly is replaced, it is essential to adapt the amount of compressor oil.
The following procedure only applies if a new compressor with pulley assembly has a label indicating the amount of compressor oil.
Open the oil filler plug.
Transfer all of the compressor oil remaining in the previous compressor with pulley assembly into a measuring cup via the oil filler plug.
Turn the belt pulley during draining.
Read the drained amount of compressor oil from the previous compressor with pulley assembly on the measuring cup.
Add 10 cc (0.338 fl.oz) extra to the recorded amount of compressor oil as a precautionary allowance, but record at least a total of 50 cc (1.69 fl.oz).
Example:
20 cc (0.676 fl.oz) read at measuring cup.
20 cc (0.676 fl.oz) + 10 cc (0.338 fl.oz) precautionary allowance = 30 cc (1.01 fl.oz) (below 50 cc (1.69 fl.oz)).
Amount of compressor oil to be filled in a new compressor with pulley assembly = 50 cc (1.69 fl.oz).
Open the oil filler plug.
Drain the entire compressor oil from a new compressor with pulley assembly into a clean collecting vessel.
Turn the belt pulley during draining.
Immediately fill the amount of compressor oil to be filled from the collecting vessel into a clean measuring cup.
Fill the amount of compressor oil to be filled from the measuring cup into a new compressor with pulley assembly.
Renew the sealing ring.
Tighten oil filler plug.
Immediately after draining, the remaining compressor oil must be filled into the refrigerant recovery unit expansion tank.
The remaining compressor oil must be disposed of correctly if it is not immediately filled into the expansion tank of the refrigerant recovery unit.
Compressor oil drained from the previous compressor with pulley assembly must not be reused and must be disposed of correctly.
3.INSTALL COMPRESSOR WITH PULLEY ASSEMBLY
Prepare for the installation of the compressor with pulley assembly.
Install the E12 bolts (2) into the threaded support sleeve (1).
Slightly press back the threaded support sleeve (1) in the direction of the arrow with the E12 bolts (2).
Remove the E12 bolts (2) from the threaded support sleeve (1) again.
Install the compressor with pulley assembly (2).
Tighten the E12 bolts (1).
Connect the connector (2).
Replace O-rings.
Install the suction pipe sub-assembly with the T45 bolt (1) compressor with pulley assembly (3).
Install the discharge tube G with the T45 bolt (1) compressor with pulley assembly (3).
4.INSTALL ENGINE ROOM ECM BOX
5.INSTALL NO. 1 INTEGRATION RELAY
6.INSTALL ECM
7.INSTALL FAN AND GENERATOR V BELT
17700
8.INSTALL AIR CLEANER ASSEMBLY
9.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
10. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
11.WARM UP COMPRESSOR
Mechanical damage to a new compressor with pulley assembly.
An increased quantity of compressor oil in a new compressor with pulley assembly can cause mechanical damage.
Perform the running-in procedure.
Do not exceed the idle speed during running-in.
The running-in procedure for a new compressor with pulley assembly can either be performed manually or using the diagnosis system.
Manual:
Switch off the air conditioning.
Set all ventilation outlets in the instrument panel to "OPEN".
Start the engine and allow the idle speed to stabilize.
Set the blower output to a minimum of 75% of the maximum blower output.
Switch on the air conditioning and allow the engine to run at idle speed for a minimum of 2 minutes.
Switch off the air conditioning and blower.
Stop engine.
Connect the diagnosis system to the vehicle and enter the following menus:
Vehicle management / Service functions / Body / Heating and air conditioning functions / Run-in protection for A/C compressor