Home › General › MAINTENANCE › BRAKE FLUID
RM3650E _V1 General _079881 MAINTENANCE _0387646 BRAKE FLUID A

MAINTENANCE  BRAKE FLUID  REPLACEMENT  


CAUTION / NOTICE / HINT

NOTICE:
·

Paint damage.

Mechanical or chemical action may lead to paint damage.

-

Cover up working area with specified covering material only.



·

Use only approved brake fluids, see operating fluids.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 55878B 1.REMOVE COWL VENT COVER

Hide 2.FILL RESERVOIR WITH BRAKE FLUID

a.
C413357

Remove the brake master cylinder reservoir filler cap.


b.
C413356

Top up the brake fluid expansion tank to the lower edge of the thread (1) with new brake fluid.

Brake Fluid and Hydraulic Fluid:

Brake fluid DOT4, low viscosity


NOTICE:

Use only approved brake fluids, see operating fluids.



Hide 3.BLEED REAR BRAKE

NOTICE:
·

Bleed the brake line of the wheel farthest from the master cylinder first.

·

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brake lines.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



a.

Start flushing at the rear right.


b.
C413353

Connect a vinyl tube to the bleeder plug (1) on rear disc brake cylinder assembly.


c.

Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1


d.

When fluid stops coming out, tighten the bleeder plug and release the brake pedal.*2


e.

Repeat steps *1 and *2 until all the air in the brake fluid is completely bled out and new brake fluid comes out.


f.

Tighten the bleeder plug completely.

Torque:
except 4-Pot Front Caliper : 15 N*m (153 kgf*cm, 11 ft.*lbf)
for 4-Pot Front Caliper : 18 N*m (184 kgf*cm, 13 ft.*lbf)


g.

Carry out the same procedure on the rear left wheel brake.


Hide 4.BLEED FRONT BRAKE

NOTICE:
·

Bleed the brake line of the wheel farthest from the master cylinder first.

·

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brake lines.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



a.

Start flushing at the front right.


b.

for 4-Pot Caliper:

i.
C413354

Connect a vinyl tube to the bleeder plug (1) on front disc brake cylinder assembly.


ii.

Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1


iii.

When fluid stops coming out, tighten the bleeder plug and release the brake pedal.*2


iv.

Repeat steps *1 and *2 until all the air in the brake fluid is completely bled out and new brake fluid comes out.


v.

Tighten the bleeder plug completely.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)



c.
C413355

Connect a vinyl tube to the bleeder plug (1) on front disc brake cylinder assembly.


d.

Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1


e.

When fluid stops coming out, tighten the bleeder plug and release the brake pedal.*2


f.

Repeat steps *1 and *2 until all the air in the brake fluid is completely bled out and new brake fluid comes out.


g.

Tighten the bleeder plug completely.

Torque:
except 4-Pot Front Caliper : 15 N*m (153 kgf*cm, 11 ft.*lbf)
for 4-Pot Front Caliper : 18 N*m (184 kgf*cm, 13 ft.*lbf)


h.

Carry out the same procedure on the rear left wheel brake.


i.
C413359

Install the brake master cylinder reservoir filler cap.

HINT:

Check the seal (1) on the sealing cap, replace if necessary.



Hide 5.INSPECT FOR BRAKE FLUID LEAK

Hide 6.INSPECT BRAKE FLUID LEVEL IN RESERVOIR

Hide 55878B 7.INSTALL COWL VENT COVER LH