Home › Suspension › REAR SUSPENSION › REAR LOWER ARM (for No. 1 Arm)
RM3650E _53 Suspension _079981 REAR SUSPENSION _0387956 REAR LOWER ARM(for No. 1 Arm) A

REAR SUSPENSION  REAR LOWER ARM(for No. 1 Arm)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

Tighten the bolt connection in the normal position.



PROCEDURE

Hide 48720A 1.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

a.
C413563

Position the rear No. 1 suspension arm assembly (3).


b.

Replace the 16 mm bolt (2) and 18 mm nut (1).


c.

Screw on 18 mm nut (1) and tighten hand-tight.


d.
C413562

Replace the 16 mm bolt (2) and 18 mm nut (1).


e.

Screw on 18 mm nut (1) and tighten hand-tight.


f.
C413562

Tighten the 18 mm nut (1) and use the 16 mm bolt (2) for counter support.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


g.

Using SST, tighten the 18 mm nut (1) an additional 90° and use the 16 mm bolt (2) for counter support.

SST
09900-WA010  

HINT:
·
C417459C02
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion



·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.




h.
C413563

Tighten the 18 mm nut (1) and use the 16 mm bolt (2) for counter support.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


i.

Using SST, tighten the 18 mm nut (1) an additional 90° and use the 16 mm bolt (2) for counter support.

SST
09900-WA010  

HINT:
·
C417459C02
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion



·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.




Hide 2.INSTALL FUEL TANK (for B48)

Hide 3.INSTALL FUEL TANK (for B58)

Hide 4.INSPECT AND ADJUST REAR WHEEL ALIGNMENT