Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the driver side and front passenger side.
The procedure listed below is for the driver side.
89952
1.REMOVE OCCUPANT DETECTION ECU (w/ Occupant Detection ECU)
73240
2.REMOVE FRONT SEAT INNER BELT ASSEMBLY
72044B
3.REMOVE SEAT LIFTER LEVER SUB-ASSEMBLY (w/ Back Side Support Adjuster)
Loosen the screw (1).
Remove the seat lifter lever sub-assembly (2).
71862
4.REMOVE FRONT SEAT CUSHION INNER SHIELD
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the clip (1).
Detach the guide (2) to remove the front seat cushion inner shield (3) in the direction of the arrow.
71822
5.REMOVE FRONT SEAT SIDE SHIELD
Detach the claws (1) to remove the front seat side shield (2).
6.REMOVE NO. 2 RECLINING ADJUSTER RELEASE ARM
|
Tilt in this Direction |
Detach the No. 2 reclining adjuster release arm (1) in the marked area (2) carefully.
Tilt the No. 2 reclining adjuster release arm (1) carefully in the direction of the arrow.
Detach the guide (3) to remove the No. 2 reclining adjuster release arm (1).
72495
7.REMOVE VERTICAL ADJUSTING HANDLE
Loosen the T45 screw (1).
Remove the vertical adjusting handle (2).
71812D
8.REMOVE FRONT SEAT CUSHION SHIELD
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Loosen the T20 screws (1).
Remove the front seat cushion shield (2) from the No. 2 front seat side shield bracket (3) in the direction of the arrow.
w/ Lumbar Support:
Disconnect the connector.
w/ Back Side Support Adjuster:
Disconnect the connector.
84920P
9.REMOVE FRONT LUMBAR SUPPORT POWER SEAT SWITCH (w/ Lumbar Support)
84920N
10.REMOVE FRONT SEATBACK SUPPORT POWER SEAT SWITCH (w/ Back Side Support Adjuster)
73706A
11.REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET (w/ Bracket)
73920A
12.REMOVE FRONT SEAT AIRBAG ASSEMBLY
Disconnect the connector (1) from the connector housing.
Detach the separate type front seat cushion cover (1).
Detach the clamps (2).
Detach the separate type front seatback cover (1) in the marked area.
Using a special tool 0 490 472 (00 5 020), open the fasteners (1) in the marked area.
Detach the separate type front seatback cover (1) in the marked area.
Loosen the nuts (1).
Fold the separate type front seatback cover with pad (2) to the side.
Pull the front seat airbag assembly (1) carefully from the separate type front seatback pad (2).
Remove the front seat airbag assembly (1) out carefully from the pocket in the separate type front seatback cover (3).
Make sure that the stud bolts (4) do not damage the pocket in the separate type front seatback cover.
13.REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Disconnect the connector (1).
Detach the clamp (2).
Position the separate type front seatback cover with pad (1) as illustrated.
Handle the separate type front seatback cover with pad (1) carefully to avoid damage.
Remove the separate type front seatback cover with pad (1) from the front seat headrest assembly (2).
71842
14.REMOVE FRONT SEATBACK GARNISH
Detach the claws (1).
Detach the guides (2) to remove the front seatback garnish (3) from the separate type front seatback cover with pad (4).
71074S
15.REMOVE SEPARATE TYPE FRONT SEATBACK COVER
Remove the 24 hog rings (1) and separate type front seatback cover (2) from the separate type front seatback pad with heater assembly.
71910A
16.REMOVE FRONT SEAT HEADREST ASSEMBLY
|
Remove in this Direction |
Press the lock button (1) to remove the front seat headrest assembly (2) in the direction of the arrow.
71579
17.REMOVE FRONT SEATBACK BOARD
Detach the clips (1) to remove the front seatback board (2).
71931
18.REMOVE FRONT SEAT HEADREST SUPPORT
|
Remove in this Direction |
Detach the claws (1) to remove the front seat headrest supports (2) in the direction of the arrow.
72760D
19.REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY (w/ Lumbar Support)
71183C
20.REMOVE SEATBACK SIDE SUPPORT ADJUSTER ASSEMBLY (w/ Back Side Support Adjuster)
21.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
w/ Occupant Detection ECU:
Loosen the screw (1).
Remove the cable (2) from the front seat adjuster assembly (3).
Disconnect the connector (1).
Detach the clamp (2).
Using a clip remover, detach the clips (1).
Detach the separate type front seat cushion cover with pad (2) in the marked area.
Position the separate type front seat cushion cover with pad (1) as illustrated.
Detach the separate type front seat cushion cover with pad (1) in the marked area (2).
71071S
22.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER
Remove the 21 hog rings (1) and separate type front seat cushion cover (2) from the separate type front seat cushion pad with heater assembly.
71640S
23.REMOVE SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY
w/ Lumbar Support, w/ Back Side Adjuster:
Detach the clamp (1) to separate the front seat wire.
Loosen the T50 bolts (1).
Use the same procedure for the opposite side.
Remove the separate type front seatback spring assembly (1).
24.REMOVE NO. 2 SEAT POSITION AIRBAG SENSOR (w/ Seat Position Airbag Sensor)
|
Remove in this Direction |
Remove the connectors in order from (1) to (2) and pull them out of the connector housing (3) one after another in the direction of the arrow.
Detach the clamps (1).
Loosen the bolt (1).
Pull the No. 2 seat position airbag sensor (2) out up of the front seat adjuster assembly (3) upwards and remove.
25.REMOVE SEAT POSITION SENSOR MAGNET (w/ Seat Position Airbag Sensor)
Drill out the rivet (1).
Do not drill the rivet at an angle as this will cause damage to the drill and rivet installation hole. Line up the drill with the rivet, and carefully drill out the rivet head.
Be careful as the drilled rivet will be very hot.
Remove the seat position sensor magnet (2) from the top of the front seat adjuster assembly (3).
26.REMOVE BELT WARNING OCCUPANT DETECTION SENSOR (for Front Passenger Side)
w/o Occupant Detection ECU:
Detach the cable from the holder (1) and clamp (2).
Detach the claws (1) to remove the belt warning occupant detection sensor (2).
87501
27.REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Detach the guides (1) and guide (2) to remove the seat heater control sub-assembly (3) as shown in the illustration.