Home › Engine / Hybrid System › B48 (ENGINE MECHANICAL) › CYLINDER HEAD
RM3650E _51 Engine / Hybrid System _080178 B48 ENGINE MECHANICAL _0388880 CYLINDER HEAD A

B48 ENGINE MECHANICAL  CYLINDER HEAD  DISASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:
·

Heavy component.

Heavy components can lead to injury or damage.

-

Remove and install heavy components with the aid of another person/other persons.




PROCEDURE

Hide 13501A 2.INSPECT AND ADJUST INTAKE CAMSHAFT SUB-ASSEMBLY

Hide 3.REMOVE TORSION SPRING

CAUTION:
·

Spring preload.

Danger of injury!

-

The use of the specified special tool (tool) is mandatory.

-

The described operation must be carried out properly.




HINT:

Wear safety goggles.


a.
A441629

Have the set of special tools 2 359 088 ready.

SST
09200-WA410  

Number Description
1 Clamping lever
2 Mounting for the clamping lever (fitting aid)


b.
A441428

Secure the intake camshaft sub-assembly with a conventional open-end spanner (1).


c.

Loosen bolt (2).


d.

Thread out camshaft sensor wheel (3) and remove.


e.
A441430

Position 4mm hexagon socket wrench (1) on the servo motor.


f.

Using the servo motor adjust the No. 3 camshaft sub-assembly (3) slowly in the direction of arrow to minimum lift.


g.

Make sure that the mark (2) on the No. 3 camshaft sub-assembly (3) points upwards.


h.
A441431

Thread in clamping lever (1) of special tool 2 359 088 and position it.

SST
09200-WA410  


i.
A441306

Make sure that the torsion spring (1) in the special tool 2 359 088 is correctly positioned.

SST
09200-WA410  


j.
A441432

Make sure that the torsion spring (1) is correctly positioned in the clamping lever (2) of the special tool 2 359 088.

SST
09200-WA410  


k.
A441433

Make sure that the special tool is fitted flat in the area of the cylinder head sub-assembly.


l.

Hold down lever (1) of special tool 2 359 088.

SST
09200-WA410  


m.

Close lever (2) of the special tool 2 359 088 carefully in the direction of arrow until the retaining hook (3) engages audibly.

SST
09200-WA410  


n.
A441431

Thread out clamping lever (1) of special tool 2 359 088 with pre-tensioned torsion spring carefully then remove.

SST
09200-WA410  


o.
A441435

Clamp fixture (1) of the special tool 2 359 088 in the vice (2).

SST
09200-WA410  


p.

Position clamping lever (3) of special tool 2 359 088 with pre-tensioned torsion spring (5) in direction of arrow in the mounting (1) of the special tool 2 359 088.

SST
09200-WA410  


q.

Carefully unlock retaining hook (4) of the special tool 2 359 088.

SST
09200-WA410  

i.

The torsion spring (5) is relieved.



r.

Slowly open clamping lever (3) and remove the torsion spring (5).


s.

Repeat the operations for the remaining valve spring retainers.


Hide 13908A 4.REMOVE GATE

a.
A441310

Loosen T30 bolt (1).


b.

Remove the gate (2) and place it arranged in order into 0 495 105 (11 4 480).


c.

Repeat the step for all the gates.


Hide 13800 5.REMOVE INTERMEDIATE LEVER

Hide 13501A 6.REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY

Hide 15330G 7.REMOVE SERVO MOTOR

a.
A442147

Loosen T30 bolts (1).


b.
A441207

Using a 4 mm hexagon socket wrench (2), turn the drive shaft of the servo motor (1) in the direction of the arrow.


c.

Make sure that the drive shaft of the servo motor is turned to the end stop of the eccentric shaft at a maximum.


d.

Remove servo motor (1).


Hide 13053 8.REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY

Hide 13502B 9.REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY

Hide 13801 10.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 11.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 12.REMOVE INTAKE VALVE COMPRESSION SPRING

Hide 13.REMOVE EXHAUST VALVE COMPRESSION SPRING

Hide 13711 15.REMOVE INTAKE VALVE

Hide 13715 16.REMOVE EXHAUST VALVE