Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING VALVE
RM3650E _53 Suspension _080070 TIRE PRESSURE MONITORING _0393031 TIRE PRESSURE WARNING VALVE A

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING VALVE  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Always use a new valve fitting kit when installing the tire pressure warning valve and transmitter.

·

Check that there is no oil, water or lubricant around the rim hole, tire pressure warning valve and transmitter, grommet and nut. Failing to do so may result in improper installation.



PROCEDURE

Hide 42607 1.INSTALL TIRE PRESSURE WARNING VALVE AND TRANSMITTER

a.
C420063

Install a new valve fitting (1) to the tire pressure warning valve and transmitter with a new bolt (2).


b.
C420064

Insert the tire pressure warning valve and transmitter (1) into the rim hole.

NOTICE:
·

Make sure that the tire pressure warning valve and transmitter is installed so that the printed surface can be seen. If the tire pressure warning valve and transmitter is installed upside down, it may be damaged or fail to transmit signals when driving at high speeds.

·

Check that there is no deformation or damage to the tire pressure warning valve and transmitter.

·

Check that there is no foreign matter on the grommet and around the rim hole.




c.
C417329

Install a new nut (1) by hand until it abuts.


d.

Press the tire pressure warning valve and transmitter evenly into the rim hole.


e.

Using an 11 mm deep socket wrench, tighten the nut (1).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

No further tightening is required once the nut is tightened to the specified torque.



f.
C277191C02
2.667,1.667 2.25,1.667 2.25,1.667 2.083,1.5 false 1.74,0.729 2.083,0.417 2.083,0.417 2.417,0.417 false 1.76,2.688 2.083,2.333 2.083,2.333 2.417,2.333 false 2.073,2.938 2.25,2.75 2.25,2.75 2.667,2.75 false 2.688,1.594 3,1.75 0.313,0.156 10 false *c 2.438,0.344 2.75,0.5 0.313,0.156 10 false *a 1.333,1.75 1.552,1.927 0.219,0.177 10 false *b 2.688,2.677 3,2.833 0.313,0.156 10 false *c 2.438,2.25 2.75,2.406 0.313,0.156 10 false *a 2,3.677 2.313,3.833 0.313,0.156 10 false *b
*a Mount Tool of the Mounting Machine
*b 60°
*c Rim
V100135

Rim Rotating Direction
V100144

Area for Tire Pressure Warning Valve and Transmitter


Set the tire and disc wheel onto the mounting machine as shown in the illustration.

NOTICE:
·

Position the main body of the tire pressure warning valve and transmitter in the area shown in the illustration.

·

If the tire pressure warning valve and transmitter is positioned outside this area, it will interfere with the tire bead and may be damaged.




g.

Apply a sufficient coat of soapy water or equivalent to the tire bead and rim.

NOTICE:

Do not apply soapy water or equivalent directly to the tire pressure warning valve and transmitter.



h.

Using a mounting machine, install the tire to the disc wheel.

NOTICE:
·

Make sure that the tire bead and mount tool do not interfere with the tire pressure warning valve and transmitter.

·

Make sure that the tire pressure warning valve and transmitter is not clamped by the bead and rim.




i.

Install a new valve core.


j.

Inflate the tire to the specified tire inflation pressure.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


k.

Check the surroundings of the tire pressure warning valve and transmitter for air leaks with soapy water or equivalent.

i.

If air is leaking from the valve core, press the valve core several times to remove foreign matter. Replace the valve core as necessary.


ii.

If air is leaking from around the tire pressure warning valve and transmitter, check if the grommet and nut are not deformed, damaged or contaminated with foreign matter. Replace the grommet or nut as necessary.



l.

Install the valve cap.


Hide 2.INSTALL WHEEL ASSEMBLY

Hide 4. INITIALIZATION OF TIRE PRESSURE MONITOR