DTC P0171 System Too Lean (Bank 1) |
DTC P0172 System Too Rich (Bank 1) |
DTC P0174 System Too Lean (Bank 2) |
DTC P0175 System Too Rich (Bank 2) |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0171 P0174 | With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip detection logic) |
|
| P0172 P0175 | With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip detection logic) |
|

| Related DTCs | P0171: Fuel trim Lean (bank 1) P0172: Fuel trim Rich (bank 1) P0174: Fuel trim Lean (bank 2) P0175: Fuel trim Rich (bank 2) |
| Required Sensors/Components (Main) | Fuel system |
| Required Sensors/Components (Related) | A/F sensor, Mass air flow meter, Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | Within 10 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0010, P0020 (OCV Bank 1, 2) P0011 (VVT System 1 - Advance) P0012 (VVT System 1 - Retard) P0021 (VVT System 2 - Advance) P0022 (VVT System 2 - Retard) P0031, P0032, P0051, P0052 (A/F sensor heater - Sensor 1) P0100 - P0103 (MAF meter) P0115 - P0118 (ECT sensor) P0120 - P0223, P2135 (TP sensor) P0125 (Insufficient ECT for closed loop) P0335 (CKP sensor) P0340 (CMP sensor) P0351 - P0356 (Igniter) P0500 (VSS) |
| Fuel system status | Closed-loop |
| Battery voltage | 11 V or more |
| Throttle position learning | Completed |
| Either of following conditions 1 or 2 set | - |
| 1. Engine RPM | Below 1,100 rpm |
| 2. Intake air amount per revolution | 0.22 g/rev or more |
| Catalyst monitor | No executed |
| Purge-cut | Executing |
| Either of following conditions 1 or 2 met | - |
| 1. Average between short-term fuel trim and long-term fuel trim | 35 % or more at 80°C (176°F) of ECT |
| 2. Average between short-term fuel trim and long-term fuel trim | -35 % or less at 80°C (176°F) of ECT |
| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 or AFS B2S1 (A/F) | +25 % | Rich | Less than 3.0 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5 % | Lean | More than 3.35 |
| O2S B1S2 or O2S B2S2 (HO2) | +25 % | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5 % | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Areas | ||
| 1 | Injection volume +25 % -12.5 % | ![]() | Injection volume +25 % -12.5 % | ![]() | - |
| Output voltage More than 3.35 V Less than 3.0 V | ![]() | Output voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 2 | Injection volume +25 % -12.5 % | ![]() | Injection volume +25 % -12.5 % | ![]() |
|
| Output voltage Almost no reaction | ![]() | Output voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 3 | Injection volume +25 % -12.5 % | ![]() | Injection volume +25 % -12.5 % | ![]() |
|
| Output voltage More than 3.35 V Less than 3.0 V | ![]() | Output voltage Almost no reaction | ![]() | ||
| 4 | Injection volume +25 % -12.5 % | ![]() | Injection volume +25 % -12.5 % | ![]() |
|
| Output voltage Almost no reaction | ![]() | Output voltage Almost no reaction | ![]() | ||
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC output) | Proceed To |
| P0171, P0172, P0174 or P0175 | A |
| P0171, P0172, P0174 or P0175 and other DTCs | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE CONNECTIONS |
|
| ||||
| OK | |
| 3.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leakage.
|
| ||||
| OK | |
| 4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (A/F CONTROL) |
Connect an intelligent tester to the DLC3.
Start the engine and turn the tester ON.
Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / A/F CONTROL.
Perform the A/F CONTROL operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 or AFS B2S1 (A/F) | +25 % | Rich | Less than 3.0 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5 % | Lean | More than 3.35 |
| O2S B1S2 or O2S B2S2 (HO2) | +25 % | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5 % | Lean | Less than 0.4 |
| Status AFS B1S1 or AFS B2S1 | Status O2S B1S2 or O2S B2S2 | A/F Condition and A/F Sensor Condition | Misfires | Suspected Trouble Areas | Proceed To |
| Lean/Rich | Lean/Rich | Normal | - | - | C |
| Lean | Lean | Actual air-fuel ratio lean | May occur |
| A |
| Rich | Rich | Actual air-fuel ratio rich | - |
| |
| Lean | Lean/Rich | A/F sensor malfunction | - |
| B |
| Rich | Lean/Rich | A/F sensor malfunction | - |
|
|
| ||||
|
| ||||
| A | |
| 5.READ VALUE OF INTELLIGENT TESTER (COOLANT TEMP) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / COOLANT TEMP.
Read the COOLANT TEMP twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 6.READ VALUE OF INTELLIGENT TESTER (MAF) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / MAF and COOLANT TEMP.
Allow the engine to idle until the COOLANT TEMP reaches 75°C (167°F) or more.
Read the MAF with the engine in an idling condition and at an engine speed of 2,500 rpm.
|
| ||||
| OK | |
| 7.CHECK FUEL PRESSURE |
Check the fuel pressure (Click here).
|
| ||||
| OK | |
| 8.CHECK EXHAUST GAS LEAKAGE |
|
| ||||
| OK | |
| 9.CHECK SPARK AND IGNITION |
|
| ||||
| OK | |
| 10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME) |
|
| ||||
| OK | |
| 11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the A4 or A5 A/F sensor connector.
Measure the resistance between the terminals of the A/F sensor connector.
| Tester Connections | Specified Conditions |
| HT (1) - +B (2) | 1.8 Ω to 3.4 Ω at 20°C (68°F) |
| HT (1) - AF- (4) | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 12.INSPECT AIR FUEL RATIO SENSOR HEATER RELAY |
![]() |
Remove the A/F sensor heater relay from the engine room R/B.
Check the A/F sensor heater relay resistance.
| Tester Connections | Specified Conditions |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω (when battery voltage applied to terminals 1 and 2) |
Reinstall the A/F sensor heater relay.
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the A4 or A5 A/F sensor connector.
Turn the ignition switch ON.
Measure the voltage between the +B terminal of the A/F sensor connector and body ground.
| Tester Connections | Specified Conditions |
| +B (A4-2) - Body ground | 9 to 14 V |
| +B (A5-2) - Body ground |
Turn the ignition switch OFF.
Disconnect the E5 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| HT (A4-1) - HA1A (E5-2) | Below 1 Ω |
| AF+ (A4-3) - A1A+ (E5-22) | |
| AF- (A4-4) - A1A- (E5-30) | |
| HT (A5-1) - HA2A (E5-1) | |
| AF+ (A5-3) - A2A+ (E5-23) | |
| AF- (A5-4) - A2A- (E5-31) |
| Tester Connections | Specified Conditions |
| HT (A4-1) or HA1A (E5-2) - Body ground | 10 kΩ or higher |
| AF+ (A4-3) or A1A+ (E5-22) - Body ground | |
| AF- (A4-4) or A1A- (E5-30) - Body ground | |
| HT (A5-1) or HA2A (E5-1) - Body ground | |
| AF+ (A5-3) or A2A+ (E5-23) - Body ground | |
| AF- (A5-4) or A2A- (E5-31) - Body ground |
Reconnect the ECM connector.
Reconnect the A/F sensor connector.

|
| ||||
| OK | |
| 14.REPLACE AIR FUEL RATIO SENSOR |
Replace the A/F sensor (Click here).
| NEXT | |
| 15.PERFORM CONFIRMATION DRIVING PATTERN |

| NEXT | |
| 16.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCS.
| Display (DTC output) | Proceed To |
| No output | A |
| P0171, P0172, P0174 or P0175 | B |
|
| ||||
| A | ||
| ||