Home › ENGINE ยท 2TR-FE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY
(Click here)


2. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH


G038557E01
  1. Install the engine mounting bracket front No. 1 RH with the 4 bolts.

    Torque:
    51 N*m{ 520 kgf*cm , 38 ft.*lbf }



3. INSTALL EXHAUST MANIFOLD


G038543E01
  1. Install a new gasket and the exhaust manifold with 8 new nuts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



4. INSTALL AIR SWITCHING VALVE ASSEMBLY


G037939E01
  1. Install a new gasket onto the cylinder head.

  1. Install the air switching valve with the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    G037938E01
  1. Connect the air switching valve connector.

  1. Connect the vacuum hose.



5. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


G037935E01
  1. Install the exhaust manifold heat insulator No. 1 with the 5 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



6. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


G037873E01
  1. Provisionally install the V-ribbed belt tensioner with bolts A and B.

  1. Tighten bolt B.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Check that the bolt holes of the V-ribbed belt tensioner and timing chain cover are aligned, and install bolt C.



    G038565E01
  1. Tighten bolt C.

    Torque:
    43 N*m{ 434 kgf*cm , 32 ft.*lbf }



7. INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY


A099635E01
  1. Install the No. 1 idler pulley sub-assembly with the bolt.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



8. INSTALL GENERATOR ASSEMBLY


G038189E01
  1. Install the generator with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    G038188E01
  1. Connect the generator connector.

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. Install the terminal cap.



9. INSTALL SPARK PLUG

Torque:
18 N*m{ 184 kgf*cm , 13 ft.*lbf }



10. INSTALL IGNITION COIL ASSEMBLY
(Click here)


11. INSTALL VENTILATION PIPE


G038556E01
  1. Install the ventilation pipe with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



12. INSTALL NO. 1 WATER BY-PASS PIPE


G035420E01
  1. Install a new gasket, then install the water by-pass pipe No. 1.

    Torque:
    18 N*m{ 178 kgf*cm , 13 ft.*lbf }



13. INSTALL ENGINE COOLANT TEMPERATURE SENSOR


G037562E01
  1. Install a new gasket onto the engine coolant temperature sensor.

  1. Using a 19 mm deep socket wrench, install the engine coolant temperature sensor.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



14. INSTALL KNOCK SENSOR


A087061E01
  1. Install the knock control sensor with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Make sure that the knock sensor is at the correct angle when installing.

  1. Connect the knock control sensor connector.



15. INSTALL FUEL INJECTOR ASSEMBLY


G037896E02
  1. Apply a light coat of gasoline or spindle oil to new O-rings, then install one onto each fuel injector.



    G037897E01
  1. Apply a light coat of gasoline or spindle oil to the contact surfaces of the fuel delivery pipe and the O-ring of the fuel injector.

  1. Apply a light coat of gasoline or spindle oil to the O-ring again, then install the fuel injector into the fuel delivery pipe by turning it right and left.

    NOTICE:
    Make sure that the O-ring is not cracked or jammed when installing.

  1. Check that the fuel injector rotates smoothly.
    If the fuel injector does not rotate, replace the O-ring.



16. INSTALL THERMOSTAT


G038202E01
  1. Install a new gasket onto the thermostat.

  1. Install the thermostat with the jiggle valve upward.

    HINT:
    The jiggle valve may be set within 10° to either side of the prescribed position.



17. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH


G038555E01
  1. Install engine mounting bracket front No. 1 LH with the 4 bolts.

    Torque:
    51 N*m{ 520 kgf*cm , 38 ft.*lbf }



18. INSTALL OIL LEVEL GAGE GUIDE


G037556E01
  1. Install the oil level gage guide with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



19. INSTALL OIL LEVEL GAGE SUB-ASSEMBLY


20. INSTALL ENGINE WIRE


21. INSTALL IDLE PULLEY ASSEMBLY WITH BRACKET (w/ Air Conditioning System)


G037912E03
  1. Using several steps, uniformly install and tighten the 5 bolts in the sequence shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf } for bolt A
    43 N*m{ 438 kgf*cm , 32 ft.*lbf } for bolt B, C



22. INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET


G037711E01
  1. Install a new gasket onto the intake manifold.

  1. Install the intake manifold with the 5 bolts and 2 nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



    G037710E01
  1. Connect the engine wire harness to the relay block.

  1. Install the nut shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 3 connectors.



    G037709E01
  1. Install the harness clamp bracket with the bolt.

    Torque:
    8.2 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Engage the wire harness clamp.

  1. Connect the compressor magnetic clutch connector. (w/ AIR CONDITIONING)

  1. Engage the engine wire harness clamp.

  1. Connect the VSV connector.



    G039455E01
  1. Connect the ventilation hose No. 3.



    G039454E01
  1. Connect the water by-pass hose No. 2.



    G037706E01
  1. Install the clamp bracket with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 in.*lbf }



    G037705E01
  1. Connect the vacuum hose.



    G037704E01
  1. Connect the fuel vapor feed hose to the VSV.



23. INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY


    G037700E01
  1. Install a new gasket onto the intake manifold.



    G037699E01
  1. Install the throttle with motor body with the 2 bolts and 2 nuts.

    Torque:
    9 N*m{ 92 kgf*cm , 80 in.*lbf }



    G037698E01
  1. Connect the water by-pass hose.

  1. Connect the water by-pass hose No. 2.

  1. Connect the throttle motor connector.



24. INSTALL NO. 2 FUEL HOSE


G037904E01
  1. Align the fuel hose connector with the pipe stem, and insert the fuel hose until the retainer makes a "click" sound.

  1. Push down the checker of the fuel hose.

    NOTICE:
    1. Check that there are no scratches or foreign objects around the disconnected parts of the fuel hose connector and pipe before performing this work.
    1. After connecting the fuel hose, check that the fuel hose is securely connected by pulling the fuel hose connector and pipe.

  1. Push the fuel hose down until the checker of the fuel hose makes a "click" sound.



25. INSTALL FUEL HOSE


G037903E01
  1. Align the fuel hose connector with the pipe stem, and insert the fuel hose until the retainer makes a "click" sound.

  1. Push down the checker of the fuel hose.

    NOTICE:
    1. Check that there are no scratches or foreign objects around the disconnected parts of the fuel hose connector and pipe before performing this work.
    1. After connecting the fuel hose, check that the fuel hose is securely connected by pulling the fuel hose connector and pipe.

  1. Push the fuel hose down until the checker of the fuel hose makes a "click" sound.



26. INSTALL INTAKE AIR CONNECTOR


    G037697E01
  1. Install the intake air connector with the 3 bolts.

    Torque:
    8 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Tighten the 2 hose clamp bolts.

    Torque:
    5 N*m{ 51 kgf*cm , 44 in.*lbf }



    G037696E01
  1. Connect the vacuum hose.



    G037695E01
  1. Connect the ventilation hose No. 2.



    G037694E01
  1. Connect the vacuum hose.

  1. Engage the wire harness clamp.

  1. Connect the pressure sensor connector.



27. INSTALL REAR END PLATE
  1. Install the rear end plate with the 2 bolts.

    Torque:
    18 N*m{ 178 kgf*cm , 13 ft.*lbf }



28. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)


G038107E01
  1. Clean the 10 bolts and 10 bolt holes.

  1. Apply adhesive to 2 or 3 threads of the 10 bolts.

    Adhesive:
    Part No. 08833-00070, THREE BOND 1324 or equivalent

  1. Provisionally install the drive plate spacer front, drive plate and ring gear and drive plate rear with the 10 bolts.

  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A099868E06
  1. Using several steps, uniformly install and tighten the 10 bolts in the sequence shown in the illustration.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 1 hour after installation.



29. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)


G038107E01
  1. Clean the 10 bolts and 10 bolt holes.

  1. Apply adhesive to 2 or 3 threads of the 10 bolts.

    Adhesive:
    Part No. 08833-00070, THREE BOND 1324 or equivalent

  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    G035062E04
  1. Using several steps, uniformly install and tighten the 10 bolts in the sequence shown in the illustration.

    Torque:
    27 N*m{ 270 kgf*cm , 20 ft.*lbf }



    G035063E01
  1. Mark the bolts with paint as shown in the illustration.

  1. Retighten the bolts by 90° in the same sequence as in step (d).

  1. Check that the paint mark of each bolt is at a 90° from the original position.

    NOTICE:
    Do not start the engine for at least 1 hour after installation.



30. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)
Transmission
See page
R155
Click here
R155F
Click here


31. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)
Transmission
See page
R155
Click here
R155F
Click here


32. INSTALL ENGINE ASSEMBLY


G038554E01
  1. Attach the engine sling device and chain block to the engine hangers.

  1. Keep the engine level, and align the engine mounting bracket front No. 1 RH w/ engine mounting insulator front and LH with the body mountings.

  1. Attach the engine mounting bracket front No. 1 RH w/ engine mounting insulator front and LH, and install the 4 bolts and nuts.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

  1. Remove the bolts, then remove the engine hangers.



33. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
(Click here)


34. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY
Transmission
See page
R155
Click here
R155F
Click here


35. INSTALL FRONT EXHAUST PIPE ASSEMBLY


A077857E01
  1. Check the free length.

    1. Using vernier calipers, measure the free length of the compression spring.

      Minimum:
      40.5 mm (1.594 in.)

      If the free length is less than the minimum, replace the compression spring.



    A076194E06
  1. Using a wooden block and plastic-faced hammer, tap in a new gasket until it is flush with the exhaust manifold.

    NOTICE:
    1. Make sure that the gasket is in the correct angle when installing.
    2. Do not reuse the removed gasket.
    3. Never push a new gasket into the exhaust manifold by installing the exhaust pipe front into the exhaust manifold.

  1. Install the exhaust pipe front into the exhaust pipe support.

  1. Tighten the 2 bolts and 2 compression springs.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



36. INSTALL EXHAUST PIPE ASSEMBLY TAIL
  1. Install a new gasket onto the exhaust pipe front.

  1. Install the exhaust pipe tail onto the 4 exhaust pipe supports.

  1. Tighten the 2 bolts and 2 nuts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }



37. INSTALL ENGINE WIRE


38. CONNECT NO. 1 AIR INJECTION HOSE


G038553E01
  1. Connect the fuel vapor feed hose.



39. CONNECT FUEL VAPOR FEED HOSE ASSEMBLY


G038552E01
  1. Connect the fuel feed hose.



40. CONNECT NO. 2 FUEL HOSE


G037904E01
  1. Align the fuel hose connector with the pipe stem, and insert the fuel hose until the retainer makes a "click" sound.

  1. Push down the checker of the fuel hose.

    NOTICE:
    1. Check that there are no scratches or foreign objects around the disconnected parts of the fuel hose connector and pipe before performing this work.
    1. After connecting the fuel hose, check that the fuel hose is securely connected by pulling the fuel hose connector and pipe.

  1. Push the fuel hose down until the checker of the fuel hose makes a "click" sound.



41. CONNECT FUEL HOSE


G037903E01
  1. Align the fuel hose connector with the pipe stem, and insert the fuel hose until the retainer makes a "click" sound.

  1. Push down the checker of the fuel hose.

    NOTICE:
    1. Check that there are no scratches or foreign objects around the disconnected parts of the fuel hose connector and pipe before performing this work.
    1. After connecting the fuel hose, check that the fuel hose is securely connected by pulling the fuel hose connector and pipe.

  1. Push the fuel hose down until the checker of the fuel hose makes a "click" sound.



42. INSTALL WATER HOSE SUB-ASSEMBLY


G038551E01
  1. Install the water hose.



43. INSTALL RADIATOR HOSE INLET


44. INSTALL COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System)


G038234E01
  1. Install the compressor and magnetic clutch with the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Connect the compressor and magnetic clutch connector.



    G038205E01
  1. Install the bolt shown in the illustration.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



45. INSTALL NO. 2 RADIATOR HOSE


46. INSTALL VANE PUMP ASSEMBLY


G037555E01
  1. Install the vane pump with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Connect the vane pump connector.



47. INSTALL AIR CLEANER CASE
  1. Install the air cleaner case with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



48. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


49. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


G037934E01
  1. Install the air cleaner cap together with the air cleaner hose No. 1.

  1. Connect the 2 air cleaner clamps.

  1. Tighten the hose clamp bolt, then connect the air cleaner hose No. 1.

  1. Connect the wire harness clamp.

  1. Connect the mass air flow meter connector.



50. INSTALL FAN SHROUD


G038211E02
  1. Install the fan pulley.



    G038210E02
  1. Install the fan shroud and fan with fluid coupling together.

    NOTICE:
    Make sure that the fan shroud and fan with fluid coupling do not make any contact with the radiator when they are installed.

  1. Provisionally install the fan with fluid coupling with the 4 nuts.



    G038564E01
  1. Install the 2 bolts shown in the illustration.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    G038208E02
  1. Connect the oil cooler inlet and outlet hoses to the fan shroud. (for Automatic Transmission)



    G038207E02
  1. Connect the radiator reserve tank hose to the radiator.

  1. Install the fan generator V belt.



    A086838E02
  1. Tighten the 4 nuts shown in the illustration.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



51. INSTALL RADIATOR SUPPORT TO FRAME SEAL LH


G038206E01
  1. Install the radiator support frame seal LH with the 9 clips.



52. INSTALL BATTERY TRAY


53. INSTALL BATTERY


54. ADD ENGINE COOLANT
  1. Tighten the engine drain plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain plug.

  1. Disconnect the 2 vinyl hoses.

  1. Slowly fill the system with engine coolant.

    Capacity:
    M/T: 8.7 liters (9.2 US qts, 7.7 lmp. qts)
    A/T: 8.6 liters (9.1 US qts, 7.6 lmp. qts)

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids.)
    3. New Toyota vehicles are filled with Toyota Super Long Life Coolant. When replacing the coolant, Toyota Super Long Life Coolant (color is pink, premixed ethylene glycol concentration is approximately 50 % and freezing temperature is -35°C (-31°F)) is recommended.

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. Check the coolant level inside the radiator by squeezing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add coolant.

  1. Install the radiator cap securely.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

    Item
    Condition
    Fan speed
    Any setting except OFF
    Temperature
    Toward warm
    Air condition switch
    OFF

  1. Squeeze the inlet and outlet radiator hoses several times by hand while warning up the engine.

  1. Stop the engine and wait until the coolant cools down.

  1. Remove the radiator cap and check the coolant level inside the radiator.

  1. If the coolant level is below the full level, perform the steps from (d) through (k) and repeat the operation until the coolant level remains at the full level.

  1. Check the coolant level inside the radiator reservoir tank again. If it is below the full level, add coolant.

  1. Install the engine under cover No. 1 with the 4 bolts. (PRE RUNNER AND 4WD TYPE)

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



55. ADD ENGINE OIL
  1. Fill with fresh engine oil.

    Capacity:

    Drain and refill with oil filter change
    5.8 liters (6.1 US qts, 5.1 lmp. qts)
    Drain and refill without oil filter change
    5.1 liters (5.4 US qts, 4.5 lmp. qts)
    Dry fill
    6.1 liters (6.4 US qts, 5.4 lmp. qts)



56. CHECK FOR ENGINE OIL LEVEL


57. CHECK FOR FUEL LEAKAGE


58. CHECK FOR ENGINE COOLANT LEAKAGE


G038195E01

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Fluid and steam could be blown out under pressure.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Pump it up to 118 kPa (1.2 kgf/cm2, 17.1 psi) and check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hose, radiator and water pump for leakage. If no external leakage is found, check the heater core, cylinder block and cylinder head.



59. CHECK FOR OIL LEAKAGE


60. CHECK FOR EXHAUST GAS LEAKAGE


61. INSPECT IGNITION TIMING


G035612E02
  1. When using a intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester ON.

    4. Start the engine and warm it up.

    5. Select the following menu items:
      DIAGNOSIS / ENHANCED OBDII / DATA LIST / PRIMARY / IGN ADVANCE.

      Ignition timing:
      3 to7°BTDC (during idling)

      NOTICE:
      Turn all electrical systems OFF.

      HINT:
      Refer to the intelligent tester operator's manual for further information regarding the selection of DATA LIST.

    6. Check that the ignition timing advances immediately when engine speed is increased.



  1. When not using a intelligent tester:

    1. Turn the ignition switch to ON.

    2. Start the engine and warm it up.



    3. G037575E01
    4. Install the tester terminal of a timing light in the position shown in the illustration.

      NOTICE:
      1. Use a timing light that detects the first signal.
      2. After checking, be sure to wrap the wire harness with tape.



    5. A118802E01
    6. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      Be careful not to connect the wrong terminals. It may damage the engine.

    7. Check that the ignition timing is within the specification.

      Ignition timing:
      3 to7° BTDC (during idling)

      NOTICE:
      Turn all electrical systems OFF.



62. INSPECT ENGINE IDLE SPEED


G035612E02
  1. When using a intelligent tester:

    1. Connect the intelligent tester to the DLC3

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester ON.

    4. Start the engine and warm it up.

    5. Select the following menu items:
      DIAGNOSIS / ENHANCED OBDII / DATA LIST / PRIMARY / ENGINE SPD.

      Idling speed:
      600 to 700 rpm

      NOTICE:
      1. Turn all electrical system OFF.
      2. When checking the idling speed, the transmission is in the neutral position.

      HINT:
      Refer to the intelligent tester operator's manual for further information regarding the selection of DATA LIST.



    A118802E02
  1. When not using a intelligent tester:

    1. Turn the ignition switch ON.

    2. Start the engine and warm it up.

    3. Install SST onto terminal 9 (TAC) of the DLC3. Connect a tachometer, then measure the engine idling speed.

      SST
      09843-18030  

      Idling speed:
      600 to 700 rpm

      NOTICE:
      1. Turn all electrical systems OFF.
      2. When checking the idling speed, the transmission should be in the neutral position.



63. INSPECT CO/HC

HINT:
This inspection is for checking whether the CO/HC concentration in the emission gas while idling complies with the regulations.

  1. Start the engine.

  1. Keep the engine speed at 2,500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe while idling.

  1. Immediately check the CO/HC concentration while idling and/or at 2,500 rpm.

    HINT:
    When performing the 2 mode (2,500 rpm and idle) test, follow the applicable local regulations. If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.


    1. Check the A/F sensor and heated oxygen sensor operation.

    2. See the table below for possible causes, then inspect and correct the applicable parts if necessary.

      CO
      HC
      Problems
      Causes
      Normal
      High
      Rough idling
      1. Faulty ignition:
        1. Incorrect timing
        2. Fouled, shorted or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leakage in intake and exhaust valves
      4. Leakage in cylinders
      Low
      High
      Rough idling
      (Fluctuation HC reading)
      1. Vacuum leakage:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idling
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty SFI systems:
        1. Faulty pressure regulator
        2. Faulty engine coolant temperature sensor
        3. Faulty mass air flow meter
        4. Faulty ECM
        5. Faulty injectors
        6. Faulty throttle body



64. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Pre Runner and 4WD Type)
  1. Install the engine under cover No. 1 with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



65. INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (for Pre Runner and 4WD Type, Regular Cab)
  1. Install the engine under cover No. 2 with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



66. INSTALL HOOD SUB-ASSEMBLY
(Click here)