Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1650/32    Occupant Classification System Malfunction

for Preparation Click here


DESCRIPTION

The occupant classification system circuit consists of the center airbag sensor assembly and the occupant classification system.
When the center airbag sensor assembly receives signals from the occupant classification ECU, it determines whether or not the front passenger airbag assembly, front seat airbag assembly RH and seat belt pretensioner RH should be operated.
DTC B1650/32 is set when a malfunction is detected in the occupant classification system circuit.

DTC No.
DTC Detecting Conditions
Trouble Areas
B1650/32
  1. Occupant classification system malfunction
  2. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the occupant classification system circuit for 2 seconds
  3. Center airbag sensor assembly malfunction
  1. Occupant classification system
  2. Center airbag sensor assembly
  3. Floor wire
  4. No. 1 seat wire

WIRING DIAGRAM


H101915E01


INSPECTION PROCEDURE

CAUTION:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. (a) Turn the ignition switch to the LOCK position.
  2. (b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. (c) Disconnect the connectors from the center airbag sensor assembly.
  4. (d) Disconnect the connectors from the steering pad.
  5. (e) Disconnect the connector from the front passenger airbag assembly.
  6. (f) Disconnect the connector from the front seat airbag assembly LH.
  7. (g) Disconnect the connector from the front seat airbag assembly RH.

    HINT:
    Skip the following steps if side and curtain shield airbags are not fitted.

  1. (h) Disconnect the connector from the curtain shield airbag assembly LH.
  2. (i) Disconnect the connector from the curtain shield airbag assembly RH.
  3. (j) Disconnect the connector from the front seat outer belt assembly LH.
  4. (k) Disconnect the connector from the front seat outer belt assembly RH.
1.CHECK DTC (CENTER AIRBAG SENSOR ASSEMBLY)


    H101849E01
  1. Turn the ignition switch to the ON position.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1650/32 is not output.

HINT:
DTCs other than B1650/32 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK DTC (OCCUPANT CLASSIFICATION ECU)
  1. Turn the ignition switch to the ON position, and wait for at least 10 seconds.

  1. Using the intelligent tester, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC is not output.



NG
GO TO DTC CHART
OK


3.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the occupant classification ECU.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


4.CHECK CONNECTORS
  1. Check that the connectors (on the center airbag sensor assembly side and occupant classification ECU side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


5.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (FOR OPEN)


    H101922E01
  1. Disconnect the connectors from the center airbag sensor assembly and the occupant classification ECU.

  1. Separate Seat :
    Using a service wire, connect O5-8 (FSR+) and O5-4 (FSR-) of connector E.

NOTICE:
Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Bench Seat :
    Using a service wire, connect O10-11 (FSR+) and O10-12 (FSR-) of connector E.

NOTICE:
Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-12 (FSP+) - A23-13 (FSP-)
    Always
    Below 1 Ω



NG
Go to step 13
OK


6.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (FOR SHORT)


    H101851E01
  1. Disconnect the service wire from connector E.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-12 (FSP+) - A23-13 (FSP-)
    Always
    1 MΩ or Higher



NG
Go to step 14
OK


7.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (TO B+)


    H101851E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A23-12 (FSP+) - Body ground
    Ignition switch ON
    Below 1 V
    A23-13 (FSP-) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 15
OK


8.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (TO GROUND)


    H101851E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-12 (FSP+) - Body ground
    Always
    1 MΩ or Higher
    A23-13 (FSP-) - Body ground
    Always
    1 MΩ or Higher



NG
Go to step 16
OK


9.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    H101849E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the center airbag sensor assembly (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1650/32 is output (for separate seat)
    A
    DTC B1650/32 is not output (for bench seat)
    B
    DTC B1650/32 is not output
    C

HINT:
DTCs other than B1650/32 may be output at this time, but they are not related to this check.



B
Go to step 17

C
END
A


10.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).


NEXT


11.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, perform the zero point calibration (Click here).

    OK:
    COMPLETED is displayed on the tester.


NEXT


12.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform the sensitivity check (Click here).

    Standard Value:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

END 

13.CHECK NO. 1 SEAT WIRE (FOR OPEN)


    H101923E01
  1. Disconnect the No. 1 seat wire connector from the instrument panel wire.

HINT:
The service wire has already been inserted into connector E.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BH1-5 (FSR+) - BH1-6 (FSR-) *1
    Always
    Below 1 Ω
    BJ2-4 (FSR+) - BJ2-5 (FSR-) *2
    Always
    Below 1 Ω

    *1 : Separate Seat
    *2 : Bench Seat



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK

REPAIR OR REPLACE FLOOR WIRE 

14.CHECK NO. 1 SEAT WIRE (FOR SHORT)


    H101924E01
  1. Disconnect the No. 1 seat wire connector from the instrument panel wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BH1-5 (FSR+) - BH1-6 (FSR-) *1
    Always
    1 MΩ or Higher
    BJ2-4 (FSR+) - BJ2-5 (FSR-) *2
    Always
    1 MΩ or Higher

    *1 : Separate Seat
    *2 : Bench Seat



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK

REPAIR OR REPLACE FLOOR WIRE 

15.CHECK NO. 1 SEAT WIRE (TO B+)


    H101924E01
  1. Disconnect the No. 1 seat wire connector from the instrument panel wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    BH1-5 (FSR+) - Body ground *1
    Ignition switch ON
    Below 1 V
    BH1-6 (FSR-) - Body ground *1
    Ignition switch ON
    Below 1 V
    BJ2-4 (FSR+) - Body ground *2
    Ignition switch ON
    Below 1 V
    BJ2-5 (FSR-) - Body ground *2
    Ignition switch ON
    Below 1 V

    *1 : Separate Seat
    *2 : Bench Seat



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK

REPAIR OR REPLACE FLOOR WIRE 

16.CHECK NO. 1 SEAT WIRE (TO GROUND)


    H101924E01
  1. Disconnect the No. 1 seat wire connector from the instrument panel wire.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BH1-5 (FSR+) - Body ground *1
    Always
    1 MΩ or Higher
    BH1-6 (FSR-) - Body ground *1
    Always
    1 MΩ or Higher
    BJ2-4 (FSR+) - Body ground *2
    Always
    1 MΩ or Higher
    BJ2-5 (FSR-) - Body ground *2
    Always
    1 MΩ or Higher

    *1 : Separate Seat
    *2 : Bench Seat



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK

REPAIR OR REPLACE FLOOR WIRE 

17.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, read the current setting data stored in the occupant classification ECU (Click here).

    HINT:
    If the previous ECU data cannot be stored in the intelligent tester, replace the front seat cushion assembly (with occupant classification ECU, occupant classification sensor).

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Using an intelligent tester, write the setting data read from the previously installed occupant classification ECU into the newly installed occupant classification ECU (Click here).


NEXT


18.PERFORM SENSITIVITY CHECK
  1. Perform the sensitivity check (Click here).


NEXT

END