Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1210/36    Zero Point Calibration of Yaw Rate Sensor Undone

DTC    C1336/39    Zero Point Calibration of Acceleration Sensor Undone

for Preparation Click here


DESCRIPTION

Skid control ECU receives signals from the yaw rate sensor and deceleration sensor via the CAN communication system.
The deceleration sensor is built into the yaw rate sensor.
If there is trouble in the bus lines between the yaw rate sensor and deceleration sensor and the CAN communication system, the DTCs U0123/62 (yaw rate sensor communication trouble) and U0124/95 (deceleration sensor communication trouble) are output.
These DTCs are also output when the calibration has not been completed.

DTC No.
DTC Detecting Conditions
Trouble Areas
C1210/36
When either of following 1 or 2 detected:
  1. When battery terminal connected, shift lever moved to non-P position (A/T), parking brake OFF (M/T) within 15 seconds of ECU terminal IG1 initially turned ON.
  2. Yaw rate sensor zero point recorded in ECU deleted.
  1. Yaw rate sensor and deceleration sensor
  2. Zero point calibration not complete
  3. PNP switch circuit (P position) (A/T)
  4. Parking brake switch circuit (M/T)
C1336/39
When either of following 1 or 2 detected:
  1. In TEST mode, shift lever shifted to non-P position (A/T), parking brake OFF (M/T) 2 seconds after ECU terminal IG1 initially turned ON.
  2. Deceleration sensor zero point recorded in ECU deleted.
  1. Yaw rate sensor and deceleration sensor
  2. Zero point calibration not complete
  3. PNP switch circuit (P position) (A/T)
  4. Parking brake switch circuit (M/T)

WIRING DIAGRAM


C124768E01


INSPECTION PROCEDURE

HINT:
When U0073/94, U0100/65, U0123/62, U0124/95 or U0126/63 are output accompanied by C1210/36 or C1336/39, inspect and repair the trouble areas indicated by U0073/94, U0100/65,U0123/62, U0124/95 or U0126/63 first.

1.PERFORM YAW RATE AND DECELERATION SENSOR ZERO POINT CALIBRATION
  1. Perform the zero point calibration of the yaw rate sensor and deceleration sensor (Click here).


NEXT


2.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check if the same DTCs are recorded.

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A


3.CHECK YAW RATE AND DECELERATION SENSOR INSTALLATION
  1. Check that the yaw rate and deceleration sensor has been installed properly (Click here).

    OK:
    The sensor is tightened to the specified torque.
    The sensor is not tilted.



NG
INSTALL YAW RATE SENSOR CORRECTLY
OK


4.CHECK HARNESS AND CONNECTOR (ECU - PARK/NEUTRAL POSITION SWITCH OR PARKING BRAKE SWITCH)


  1. A/T



      F052381E01
    1. Disconnect the skid control ECU connector.

    2. Disconnect the Park/Neutral position switch connector.

    3. Measure the resistance.

      Standard Resistance:
      Tester Connection
      Specified Condition
      S1-14 (P/R) - P1-6 (RL)
      Below 1 Ω

    4. Reconnect the Park/Neutral position switch connector.

    5. Reconnect the skid control ECU connector.



  1. M/T:



      C124797E01
    1. Disconnect the skid control ECU connector.

    2. Disconnect the parking brake switch connector.

    3. Measure the resistance.

      Standard Resistance:
      Tester Connection
      Specified Condition
      S1-28 (PKB) - P6-1
      Below 1 Ω

    4. Reconnect the parking brake switch connector.

    5. Reconnect the skid control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT PARK/NEUTRAL POSITION SWITCH OR PARKING BRAKE SWITCH


  1. Inspect the Park/Neutral Position (PNP) switch (for A/T models).



      C124790E01
    1. Disconnect the P1 PNP switch connector.

    2. Check the resistance when the transmission gear selector lever is moved to each position.

      Standard Resistance:
      Gear Selector Lever Positions
      Tester Connections
      Specified Conditions
      P
      2 - 6, 4 - 5
      Below 1 Ω
      R
      1 - 2
      Below 1 Ω
      N
      2 - 9, 4 - 5
      Below 1 Ω
      D
      2 - 7
      Below 1 Ω
      2
      2 - 3
      Below 1 Ω
      L
      2 - 8
      Below 1 Ω

    3. Reconnect the PNP switch connector.



  1. Inspect the parking brake switch (for M/T models).



      G026238E06
    1. Disconnect the parking brake switch connector.

    2. Measure the resistance.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      P6-1 Ground part
      Released
      Below 1 Ω
      P6-1 Ground part
      Pushed in
      Below 1 Ω

    3. Reconnect the parking brake switch connector.



NG
REPLACE PARK/NEUTRAL POSITION SWITCH OR PARKING BRAKE SWITCH
OK


6.REPLACE YAW RATE AND DECELERATION SENSOR
  1. Replace the yaw rate and deceleration sensor (Click here).


NEXT


7.PERFORM YAW RATE AND DECELERATION SENSOR ZERO POINT CALIBRATION
  1. Perform the zero point calibration of the yaw rate sensor and deceleration sensor (Click here).


NEXT


8.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check if the same DTCs are recorded.

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID