Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2111    Throttle Actuator Control System - Stuck Open

DTC    P2112    Throttle Actuator Control System - Stuck Closed

for Preparation Click here


DESCRIPTION

The throttle actuator is operated by the ECM, and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body assembly. The throttle position sensor provides feedback to the ECM so that the ECM can control the throttle actuator (throttle valve) appropriately in response to driver inputs.

HINT:
This ETCS (Electronic Throttle Control System) does not use a throttle cable.

DTC No.
DTC Detection Condition
Trouble Area
P2111
Throttle actuator does not close even when the ECM commands it to close
(1 trip detection logic)
  1. Throttle actuator
  1. Throttle body assembly
  1. Throttle valve
  2. Wire harness or connector
P2112
Throttle actuator does not open even when the ECM commands it to open
(1 trip detection logic)
  1. Throttle actuator
  1. Throttle body assembly
  2. Throttle valve
  3. Wire harness or connector


MONITOR DESCRIPTION

The ECM determines that there is a malfunction in the ETCS when the throttle valve remains at a fixed angle despite a high drive current from the ECM. The ECM illuminates the MIL and stores the DTC.
If the malfunction is not repaired successfully, a DTC is stored when the accelerator pedal is fully depressed and released quickly (to fully open and close the throttle valve) after the engine is next started.

MONITOR STRATEGY


Related DTCs
P2111: Throttle Actuator Stuck Open
P2112: Throttle Actuator Stuck Closed
Required Sensors/Components (Main)
Throttle actuator (throttle body assembly)
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs not present
None

P2111 (Throttle actuator stuck open): 
All of following conditions met
-
System guard* judge condition
ON
Throttle actuator current
2 A or higher
Duty cycle to close throttle
80% or more

P2112 (Throttle actuator stuck closed): 
All of following conditions met
-
System guard* judge condition
ON
Throttle actuator current
2 A or higher
Duty cycle to open throttle
80% or more

* System guard set when the following conditions are met
-
Throttle actuator
ON
Throttle actuator duty calculation
Executing
Throttle position sensor fail
Not detected
Throttle actuator current-cut operation
Not executing
Throttle actuator power supply
4 V or higher
Throttle actuator fail
Not detected

TYPICAL MALFUNCTION THRESHOLDS


P2111 (Throttle actuator stuck open): 
Throttle position sensor voltage change
No change

P2112 (Throttle actuator stuck closed): 
Throttle position sensor voltage change
No change

CONFIRMATION DRIVING PATTERN


A199314E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and fully depress and release the accelerator pedal quickly (to fully open and close the throttle valve).
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  8. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P2111 or P2112.
  11. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


FAIL-SAFE

When either of these DTCs or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 6.5° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

Refer to DTC P2102 .

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Refer to "Data List / Active Test" [Throttle Position Command, Throttle Position No. 1, Throttle Motor Current, Throttle Motor Duty (Open), Throttle Motor Duty (Close)] (Click here).

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2111 OR P2112)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    DTC P2111 or P2112 is output
    A
    DTC P2111 or P2112 and other DTCs are output
    B

    HINT:
    If any DTCs other than P2111 or P2112 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT THROTTLE BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
  1. Check for contamination between the throttle valve and housing. If necessary, clean the throttle body assembly. Also check that the throttle valve moves smoothly.

    OK:
    Throttle valve is not contaminated with foreign objects and moves smoothly.



NG
Go to step 5
OK


3.READ VALUE USING TECHSTREAM (THROTTLE POSITION)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.

  1. Read the values displayed on the Techstream while wiggling the ECM wire harness.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    Value in Data List changes when wire harness is wiggled, or DTC is output*
    A
    Other than above
    B

    1. *: As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (Click here).



B
Go to step 6
A


4.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE BODY)
  1. As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (Click here).


NEXT

END 

5.REPLACE THROTTLE BODY ASSEMBLY
  1. Replace the throttle body assembly (Click here).


NEXT


6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P2111 or P2112 is output
    B



B
REPLACE ECM (Click here)
A

END