Home › CRUISE CONTROL SYSTEM › CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > Cruise Control Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends signals to the ECM depending on the cruise control main switch condition.
The battery supplies the positive (+) battery voltage to the cruise control main switch. Then terminal CCS of the ECM receives the voltage as the signal according to the switch condition.

WIRING DIAGRAM


E170563E01


INSPECTION PROCEDURE

1.INSPECT CRUISE CONTROL MAIN SWITCH


  1. Remove the cruise control main switch (Click here).


    E106137E23

  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance:

Tester Connection
Switch Condition
Specified Condition
1 - 3
+ (ACCEL)/RES (RESUME)
235 to 245 Ω
1 - 3
- (COAST)/SET
617 to 643 Ω
1 - 3
CANCEL
1,509 to 1,571 Ω
1 - 3
Main Switch OFF
10 kΩ or higher
1 - 3
Main Switch ON
Below 1 Ω

  1. Reinstall the cruise control main switch.



NG
REPLACE CRUISE CONTROL MAIN SWITCH (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (CRUISE CONTROL MAIN SWITCH - SPIRAL CABLE SUB-ASSEMBLY)


    E103330E32
  1. Disconnect the spiral cable side and main switch side connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (main switch side) - 3 ( spiral cable side)
    Always
    Below 1 Ω
    3 (main switch side) - 4 (spiral cable side)
    Always
    Below 1 Ω

  1. Reconnect the spiral cable side and main switch side connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
E144333E24

NOTICE:
The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets.

HINT:
  1. Removal (Click here).
  2. Installation (Click here).

  1. Remove the spiral cable.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (CCS) main switch side - S8-1 (CCS)
    The spiral cable position is center
    Below 1 Ω
    The spiral cable position is 2.5 rotations to the left
    The spiral cable position is 2.5 rotations to the right
    3 (ECC) main switch side - S8-2 (ECC)
    The spiral cable position is center
    Below 1 Ω
    The spiral cable position is 2.5 rotations to the left
    The spiral cable position is 2.5 rotations to the right

  1. Reinstall the spiral cable.



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)


    E170564E01
  1. Disconnect the E14 or E7 ECM connector.

  1. Disconnect the S8 spiral cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S8-2 (ECC) - Body Ground
    Always
    Below 1 Ω

    Standard Resistance (for 1GR-FE):
    Tester Connection
    Condition
    Specified Condition
    E14-11 (CCS) - S8-1 (CCS)
    Always
    Below 1 Ω
    E14-11 (CCS) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for 2TR-FE):
    Tester Connection
    Condition
    Specified Condition
    E7-31 (CCS) - S8-1 (CCS)
    Always
    Below 1 Ω
    E7-31 (CCS) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the spiral cable connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE