Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

DTC    B2799    Engine Immobiliser System Malfunction

for Preparation Click here


DESCRIPTION

This DTC is output when one of the following occurs: 1) the ECM detects errors in its own communications with the immobiliser code ECU; 2) the ECM detects errors in the communication lines; or 3) the ECU communication ID between the immobiliser code ECU and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no certification ECU DTCs are present. If present, troubleshoot the certification ECU DTCs first.

DTC Code
DTC Detection Condition
Trouble Area
B2799
  1. Error in communication between ECM and transponder key ECU, and in communication line
  2. Error in communication lines
  3. Communication ID is different during communication with transponder key ECU
  1. Wire harness or connector
  2. ECM
  3. Transponder key ECU assembly

WIRING DIAGRAM


B205062E01


INSPECTION PROCEDURE

HINT:
  1. If the transponder key ECU assembly is replaced, register the key and ECU communication ID.
  2. If the ECM is replaced, register the ECU communication ID.

1.CHECK FOR DTC
  1. Clear the DTC (Click here).

  1. Recheck for DTC.

    OK:
    DTC B2799 output does not reoccur.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.ECU COMMUNICATION ID REGISTRATION
  1. Re-register the ECU communication ID between the transponder key ECU assembly and ECM.


NEXT


3.CHECK FOR DTC
  1. Clear the DTC (Click here).

  1. Recheck for DTC.

    OK:
    DTC B2799 output does not reoccur.



NG
Go to step 4
OK

END 

4.CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch off.

  1. Check that the connectors are properly connected to the ECM and the transponder key ECU.

OK:
Connectors are properly connected.



NG
CONNECTING CONNECTORS PROPERLY
OK


5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)


    B205063E01
  1. Disconnect the T10 ECU connector.

  1. Disconnect the E7 or E14 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    T10-13 (EFIO) - E14-14 (IMI)*1
    Always
    Below 1 Ω
    T10-12 (EFII) - E14-20 (IMO)*1
    Always
    Below 1 Ω
    T10-13 (EFIO) - E7-16 (IMI)*2
    Always
    Below 1 Ω
    T10-12 (EFII) - E7-15 (IMO)*2
    Always
    Below 1 Ω
    T10-13 (EFIO) or E14-14 (IMI)*1 - Body ground
    Always
    10 kΩ or higher
    T10-12 (EFII) or E14-20 (IMO)*1 - Body ground
    Always
    10 kΩ or higher
    T10-13 (EFIO) or E7-16 (IMI)*2 - Body ground
    Always
    10 kΩ or higher
    T10-12 (EFII) or E7-15 (IMO)*2 - Body ground
    Always
    10 kΩ or higher

    1. *1: for 1GR-FE
    2. *2: for 2TR-FE

  1. Reconnect the ECU connector.

  1. Reconnect the amplifier connector.



MG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE ECM
  1. Replace the ECM.

    1. for 1GR-FE (Click here).
    2. for 2TR-FE (Click here).


NEXT


7.ECU COMMUNICATION ID REGISTRATION
  1. Re-register the ECU communication ID between the transponder key ECU assembly and ECM.


NEXT


8.CHECK FOR DTC
  1. Clear the DTC (Click here).

  1. Recheck for DTC.

    OK:
    DTC B2799 output does not reoccur.



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY (Click here)
OK

END