DTC P0505 Idle Control System Malfunction |
| DTC No. | DTC Detection Condition | Trouble Areas |
| P0505 | Idling speed continues to vary greatly from target idling speed (2 trip detection logic) |
|

| Related DTCs | P0505: ISC Function |
| Required Sensors/Components (Main) | Electronic throttle control system |
| Required Sensors/Components (Related) | Crankshaft position sensor Engine coolant temperature sensor Vehicle speed sensor |
| Frequency of Operation | Continuous |
| Duration | 10 minutes |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0010 (VVT Oil Control Valve) P0011 (VVT system - Advance) P0012 (VVT system -Retard) P0016 (VVT system - Misalignment) P0031, P0032 (Air Fuel Ratio Sensor Heater) P0102, P0103 (Mass Air Flow Meter) P0115, P0117, P0118 (Engine Coolant Temperature Sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor) P0125 (Insufficient Engine Coolant Temperature for Closed Loop Fuel Control) P014C, P014D, P015A, P015B, P2195, P2196, P2237, P2238, P2239, P2252, P2253 (Air Fuel Ratio Sensor) P0171, P0172 (Fuel System) P0301 - P0304 (Misfire) P0335 (Crankshaft Position Sensor) P0340 (Camshaft Position Sensor) P0351 - P0354 (Ignitor) P0451, P0452, P0453 (EVAP System) P0500 (Vehicle Speed Sensor) P0705 (Shift Lever Position Switch) P0973, P0974, P0976, P0977 (Shift Solenoid) |
| Engine | Running |
| Either condition is met | 1 or 2 |
| 1. Both of following conditions A and B met | - |
| A. Engine rpm - Target engine rpm | Less than - 100 rpm, or more than 150 rpm (A/C off and NSW off) Less than - 100 rpm, or more than 200 rpm (A/C on or NSW on) |
| IAC flow rate learned value | 0.5 L/sec. or less, or 6.4 L/sec. or more for 5 seconds or more |
| 2. Both of following conditions C and D met | - |
| C. Both of following conditions (a) and (b) met | 5 times or more |
| (a) Engine rpm- Target engine rpm | Less than - 100 rpm, or more than 150 rpm (A/C off and NSW off) Less than - 100 rpm, or more than 200 rpm (A/C on or NSW on) |
| (b) Vehicle condition | Stopped after being driven at 10 km/h (6.25 mph) or more |
| D. Either of following condition is met | (c) or (d) |
| (c) Amount of change of IAC learned value | +2.035 L/sec. or more, or -3.245 L/sec. or more for 5 seconds or less |
| (d) IAC flow rate learned value | 0.5 L/sec. or less, or 6.4 L/sec. or more for 5 seconds or more |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0505) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P0505 is output | A |
| DTC P0505 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE CONNECTIONS |
Check the PCV hose connections.
|
| ||||
| OK | |
| 3.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks .
|
| ||||
| OK | |
| 4.INSPECT THROTTLE BODY ASSEMBLY (THROTTLE VALVE) |
Check the throttle valve condition.
|
| ||||
| OK | |
| 5.CONFIRM WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Read DTCs.
| Result | Proceed to |
| DTC P0505 is output | A |
| No DTC is output | B |
|
| ||||
| A | ||
| ||