Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0335    Crankshaft Position Sensor "A" Circuit

DTC    P0339    Crankshaft Position Sensor "A" Circuit Intermittent

for Preparation Click here


DESCRIPTION

The crankshaft position sensor system consists of a crank angle sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the No. 2 crankshaft timing sprocket. The pickup coil is made of an iron core and a magnet.
The sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per crankshaft revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection time and ignition timing are controlled.

DTC No.
DTC Detection Condition
Trouble Area
P0335
When either of following conditions is met when camshaft position sensor circuit fail is not detected:
(1 trip detection logic)
  1. Missing crankshaft position sensor signal despite camshaft position sensor signal inputs normal after engine cranked
  2. No crankshaft position sensor signal to ECM while cranking
  3. No crankshaft position sensor signal to ECM while engine running
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. No. 2 crankshaft timing sprocket (crank angle sensor plate)
  4. ECM
P0339
Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more
(1 trip detection logic):
  1. (a) Engine speed 1000 rpm or more
  2. (b) Starter signal off
  3. (c) 3 seconds or more have elapsed since starter signal switched from on to off

  1. A063955E51
    Reference: Inspection using an oscilloscope

    HINT:
    1. The correct waveforms are as shown.
    2. G2 stands for the camshaft position sensor signal, and NE+ stands for the crankshaft position sensor signal.
    3. Grounding failure of the shielded wire may cause noise in waveforms.

    ECM Terminal Name
    (a) Between G2 and NE-
    (b) Between NE+ and NE-
    Tester Range
    5 V/DIV., 20 ms./DIV.
    Condition
    Idling

MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the engine revolving, the ECM interprets this as a malfunction of the sensor.
If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0335: Crankshaft Position Sensor Verify Pulse Input
P0335: Crankshaft Position Sensor Range Check/Rationality
Required Sensors/Components (Main)
Crankshaft position sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
4.7 seconds: Verify pulse input case 1
15 seconds: Verify pulse input case 2
0.016 seconds: Range check/rationality
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS

  1. Crankshaft Position Sensor Verify Pulse Input

    Case 1 
    Starter
    ON
    Minimum battery voltage while starter ON
    Less than 11 V

    Case 2 
    Engine speed (Top dead center)
    600 rpm or less
    Engine speed (30°CA)
    600 rpm or less
    Starter
    OFF
    Time after starter ON to OFF
    3 seconds or more

Crankshaft Position Sensor Range Check/Rationality 
All of the following conditions are met
-
Time after starter OFF to ON
3 seconds or more
Camshaft position sensor circuit fail (P0340)
Not detected
Number of camshaft position sensor signal pulse
6 times
Battery voltage
7 V or higher
Minimum battery voltage while starter ON
Less than 11 V

TYPICAL MALFUNCTION THRESHOLDS


Crankshaft Position Sensor Verify Pulse Input 
Engine speed signal
No signal

Crankshaft Position Sensor Range Check/Rationality 
Number of crankshaft position sensor signal pulse
132 times or less, or 174 times or more

COMPONENT OPERATING RANGE


Crankshaft position sensor
  1. Crankshaft position sensor output voltage fluctuates while crankshaft revolving
  2. 34 crankshaft position sensor signals per crankshaft revolution

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine.
  7. Idle the engine for 20 seconds or more [A].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0335 or P0339.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A237489E01


INSPECTION PROCEDURE

HINT:
  1. If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.
  2. After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 is output again, check the following items related to the camshaft position sensor.
    1. Installation condition of the camshaft position sensor
    2. Installation condition of the camshaft
    3. Connection of the camshaft position sensor connector
  3. Check the engine speed. The engine speed can be checked by using the Techstream. To check, follow the operation below:
    (a) Connect the Techstream to the DLC3.
    (b) Start the engine.
    (c) Turn the Techstream on.
    (d) Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
    The engine speed may be indicated as zero despite the engine revolving normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed, if the crankshaft position sensor voltage output is insufficient.
  4. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
G037726E02
  1. Disconnect the C5 crankshaft position sensor connector.

  1. Measure the resistance between terminals 1 and 2.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Cold
    1630 to 2740 Ω
    1 - 2
    Hot
    2065 to 3225 Ω

    HINT:
    Terms cold and hot refer to the temperature of the coils. Cold means approximately -10 to 50°C (14 to 122°F). Hot means approximately 50 to 100°C (122 to 212°F).



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
A240484E01
  1. Disconnect the C5 crankshaft position sensor connector.

  1. Disconnect the E4 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    C5-1 (NE) - E4-27 (NE+)
    Always
    Below 1 Ω
    C5-2 (NE-) - E4-34 (NE-)
    Always
    Below 1 Ω

    Standard Resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    C5-1 (NE) or E4-27 (NE+) - Body ground
    Always
    10 kΩ or higher
    C5-2 (NE-) or E4-34 (NE-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)
BR03795E31
  1. Check the crankshaft position sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR
OK


4.CHECK NO. 2 CRANKSHAFT TIMING SPROCKET (TEETH OF CRANK ANGLE SENSOR PLATE)
  1. Check the teeth of the crank angle sensor plate.

    OK:
    Sensor plate does not have any cracks or deformation.



NG
REPLACE NO. 2 CRANKSHAFT TIMING SPROCKET
OK

REPLACE ECM (Click here)