Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0335    Crankshaft Position Sensor "A" Circuit

DTC    P0339    Crankshaft Position Sensor "A" Circuit Intermittent

for Preparation Click here


DESCRIPTION

The crankshaft position sensor system consists of a crankshaft (sensor plate) and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and a magnet.
The sensor plate rotates and, as each tooth passes through the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection time and ignition timing are controlled.

DTC No.
DTC Detection Condition
Trouble Area
P0335
One of the following conditions is met when camshaft position sensor fail is not detected (1 trip detection logic):
  1. No crankshaft position sensor signal to ECM while cranking (1 trip detection logic)
  1. No crankshaft position sensor signal to ECM while engine running (1 trip detection logic)
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Crankshaft (sensor plate)
  4. ECM
P0339
Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more (1 trip detection logic)
  1. (a) Engine speed 1000 rpm or more
  2. (b) Starter signal OFF
  3. (c) 3 seconds or more have elapsed since starter signal switched from ON to OFF

  1. G035795E10
  2. Inspection using an oscilloscope

    HINT:
    1. The correct waveform is shown above.
    2. VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the crankshaft position sensor signal.
      Item
      Content
      Terminal
      VV1+ - VV1-
      VV2+ - VV2-
      NE+ - NE-
      Equipment Setting
      5 V/DIV, 20 ms/DIV
      Condition
      Cranking or idling


MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the engine revolving, the ECM interprets this as a malfunction of the sensor.
If the malfunction is not repaired successfully, a DTC is stored 20 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0335: Crankshaft position sensor range check/rationality
Required Sensors/Components (Main)
Crankshaft position sensor
Required Sensors/Components (Related)
VVT sensor
Frequency of Operation
Continuous
Duration
-: Verify pulse input (case 1)
0.016 seconds: Range check/rationality
4.7 seconds: Verify pulse input (case 2)
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not stored
None

P0335: Crankshaft Position Sensor Range Check/Rationality 
All of the following conditions are met
-
Engine speed signal
Signal input
Ignition switch
ON
Time after starter OFF to ON
3 seconds or more
VVT sensor circuit fail (P0340,P0342,P0343)
Not detected
Number of VVT sensor signal pulse
6 times
Battery voltage
7 V or more
Minimum battery voltage while starter ON
Less than 11 V

P0335: Crankshaft Position Sensor Verify Pulse Input (Case 1) 
All of the following conditions are met
-
Starter
OFF
Engine speed (Top dead center)
600 rpm or higher
Engine speed (30°CA)
600 rpm or higher
Time after starter from ON to OFF
3 seconds or more

P0335: Crankshaft Position Sensor Verify Pulse Input (Case 2) 
All of the following conditions are met
-
Starter
ON
Minimum battery voltage while starter ON
Less than 11 V

TYPICAL MALFUNCTION THRESHOLDS


P0335: Crankshaft Position Sensor Range Check/Rationality 
Number of crankshaft position sensor signal pulse
132 or less, or 174 or more

P0335: Crankshaft Position Sensor Verify Pulse Input 
Engine speed signal
No signal

COMPONENT OPERATING RANGE


Crankshaft position sensor
  1. Crankshaft position sensor output voltage fluctuates while crankshaft revolving
  2. 34 crankshaft position sensor signals per crankshaft revolution

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine.
  7. Idle the engine for 20 seconds or more [A].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0335 or P0339.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A254614E01


INSPECTION PROCEDURE

HINT:
  1. After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 is output again, check the following items related to the VVT sensor.
    1. Installation condition of the VVT sensor
    2. Installation condition of the camshaft
    3. Connection of the VVT sensor connector
  2. If no problem is found by this diagnostic troubleshooting procedure, troubleshoot the engine mechanical systems.
  3. Check the engine speed. The engine speed can be checked by using the Techstream. To check, follow the operation below:
    1. Connect the Techstream to the DLC3.
    2. Start the engine.
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
    1. The engine speed may be indicated as zero despite the engine revolving normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed, if the crankshaft position sensor voltage output is insufficient.
  4. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (ENGINE SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Start the engine.

  1. Read the values displayed on the Techstream while the engine is running.

    OK:
    Correct values are displayed.

    HINT:
    1. To check the engine speed change, display the graph on the Techstream.
    2. If the engine does not start, check the engine speed while cranking.
    3. If the engine speed indicated on the Techstream remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
  1. Inspect the crankshaft position sensor (Click here).



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    C5-1 - E9-6 (NE+)
    Always
    Below 1 Ω
    C5-2 - E9-5 (NE-)
    Always
    Below 1 Ω
    C5-1 or E9-6 (NE+) - Body ground
    Always
    10 kΩ or higher
    C5-2 or E9-5 (NE-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
BR03795E25
  1. Check the crankshaft position sensor installation.

    OK:
    Crankshaft position sensor is installed correctly.



NG
SECURELY REINSTALL (Click here)
OK


5.INSPECT CRANKSHAFT (TEETH OF SENSOR PLATE)
  1. Inspect the teeth of the crank angle sensor plate

    OK:
    Crank angle sensor plate does not have any cracks or deformation.



NG
REPLACE CRANKSHAFT (SENSOR PLATE)
OK


6.REPLACE CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335 AND/OR P0339)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0335 or P0339 is output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END