Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0010    Camshaft Position "A" Actuator Circuit (Bank 1)

for Preparation Click here


DESCRIPTION

The Variable Valve Timing (VVT) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.
The Camshaft Timing Oil Control Valve Assembly (OCV) is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A209140E11


DTC No.
DTC Detection Condition
Trouble Area
P0010
Open or short in camshaft timing oil control valve assembly circuit (1 trip detection logic)
  1. Open or short in camshaft timing oil control valve assembly circuit
  2. Camshaft timing oil control valve assembly
  3. ECM

MONITOR DESCRIPTION

This DTC is designed to detect open or short in the camshaft timing oil control valve assembly circuit. If the camshaft timing oil control valve's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

MONITOR STRATEGY


Related DTCs
P0010: Camshaft Timing Oil Control Valve Range Check
Required Sensors/Components (Main)
Camshaft timing oil control valve assembly
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
1 second
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
All of following conditions are met
-
Starter
OFF
Ignition switch
ON
Time after ignition switch OFF to ON
0.5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


One of following conditions met
-
A. All of following conditions are met
-
Battery voltage
11 to 13 V
Target duty cycle
Less than 70%
Output duty cycle
100%
B. All of following conditions are met
-
Battery voltage
13 V or more
Target duty cycle
Less than 80%
Output duty cycle
100%
C. All of following conditions are met
-
Current cut status
Not cut
Output signal duty cycle
3% or less

COMPONENT OPERATING RANGE


Camshaft timing oil control valve assembly duty ratio
3 to 100%

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Wait 5 seconds.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  8. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0010.
  11. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A236385E02


INSPECTION PROCEDURE

HINT:
  1. If DTC P0010 is output, check the VVT system circuit.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Turn the A/C switch on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1).

  1. Check the engine speed while operating the camshaft timing oil control valve assembly using the Techstream.

    OK:

    Techstream Operation
    Specified Condition
    0%
    Normal engine speed
    100%
    Engine idles roughly or stalls

    HINT:
    Refer to "Data List / Active Test" [VVT OCV Duty #1, VVT Change Angle #1] (Click here).



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV SIGNAL)
A094633E58
  1. Disconnect the camshaft timing oil control valve assembly connector.

  1. While idling, check the waveform between the terminals of the camshaft timing oil control valve assembly connector using an oscilloscope.

    OK:
    Tester Connection
    Condition
    Specified Condition
    C2-2 - C2-1
    Idling
    Correct waveform shown

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Camshaft Timing Oil Control Valve Assembly)
    *b
    OCV+ and OCV- Signal Waveform



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
OK


3.INSPECT ECM (OCV SIGNAL)
A093256E14
  1. Inspect the ECM using an oscilloscope.

  1. While idling, check the waveform between the terminals of the ECM connector.

    OK:
    Tester Connection
    Condition
    Specified Condition
    E4-13 (OC1+) - E4-12 (OC1-)
    Idling
    Correct waveform shown

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to ECM)
    *b
    OC1+ and OC1- Signal Waveform



NG
REPLACE ECM (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)