Home › TRANSMISSION · A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0756    Shift Solenoid "B" Performance (Shift Solenoid Valve S2)

for Preparation Click here


SYSTEM DESCRIPTION

The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd or 4th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body and automatic transmission (clutch, brake, gear, etc.).

DTC No.
DTC Detection Conditions
Trouble Areas
P0756
S2 stuck ON malfunction*1:
The vehicle starts in 2nd gear and shifting to 4th gear is impossible.
The ECM determines that there is a malfunction when both of the following conditions are met:
(a) When the ECM directs the transmission to switch to 1st gear, the actual gear is shifted to 2nd.
(b) When the ECM directs the transmission to switch to 4th gear, the actual gear is shifted to 3rd.
  1. Shift solenoid valve S2 is stuck open
  2. Valve body is blocked
  3. Shift solenoid valve S2
  4. Automatic transmission (clutch, brake, gear, etc.)
P0756
S2 stuck OFF malfunction*2:
Shifting to 2nd and 3rd gears is impossible.
The ECM determines that there is a malfunction when both of the following conditions are met:
(a) When the ECM directs the transmission to switch to 2nd gear, the actual gear is shifted to 1st.
(b) When the ECM directs the transmission to switch to 3rd gear, the actual gear is shifted to 4th.
  1. Shift solenoid valve S2 is stuck closed
  2. Valve body is blocked
  3. Shift solenoid valve S2
  4. Automatic transmission (clutch, brake, gear, etc.)

HINT:
Gear positions in the event of a solenoid valve mechanical problem:

Gear shift controlled by ECM
1st
2nd
3rd
4th
*1: Actual gear position under S2 stuck ON malfunction
2nd
2nd
3rd
3rd
*2: Actual gear position under S2 stuck OFF malfunction
1st
1st
4th
4th


MONITOR DESCRIPTION

This DTC indicates "stuck ON malfunction" or "stuck OFF malfunction" of the shift solenoid valve S2.
The ECM controls the gear shifts by turning the shift solenoid valves "ON/OFF". When the gear position directed by the ECM and the actual gear position do not match, the ECM illuminates the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0756:
Shift solenoid valve S2/OFF malfunction
Shift solenoid valve S2/ON malfunction
Required sensors/Components
Shift solenoid valve S2
Frequency of operation
Continuous
Duration
1 second
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
P0973, P0974 (Shift solenoid valve S1 circuit)
P0976, P0977 (Shift solenoid valve S2 circuit)
P0128 (ECT (Engine coolant temperature) sensor circuit)
P0722 (Output speed sensor circuit)
P0500 (Vehicle speed sensor circuit)
Transmission shift position
"D"
Duration time from shifting "N" to "D"
4 seconds or more
ECT (Engine Coolant Temperature)
40°C (104°F) or more
Spark advance from max. retard timing by knock control
0°CA or more
Engine
Starting

OFF malfunction (A) 
ECM selected gear
2nd
Vehicle speed
10 km/h (6.2 mph) or more
Output speed
2nd → 1st down-shift point or more
Throttle valve opening angle
6.5 % or more at engine speed of 2000 rpm
(Conditions vary with engine speed)

OFF malfunction (B) 
ECM selected gear
3rd
Vehicle speed
Less than 10 km/h (6.2 mph)
Throttle valve opening angle
6.5 % or more at engine speed of 2000 rpm
(Conditions vary with engine speed)

OFF malfunction (C) 
ECM selected gear
4th
Vehicle speed
10 km/h (6.2 mph) or more
Throttle valve opening angle
6.5 % or more at engine speed of 2000 rpm
(Conditions vary with engine speed)

ON malfunction (A) 
ECM selected gear
1st
Vehicle speed
10 km/h (6.2 mph) or more
and
Less than 40 km/h (24.8 mph)
Throttle valve opening angle
6.5 % or more at engine speed of 2000 rpm
(Conditions vary with engine speed)

ON malfunction (B) 
ECM selected gear
3rd
Vehicle speed
10 km/h (6.2 mph) or more
Throttle valve opening angle
6.5 % or more at engine speed of 2000 rpm
(Conditions vary with engine speed)

ON malfunction (C) 
ECM selected gear
4th
Vehicle speed
10 km/h (6.2 mph) or more
Throttle valve opening angle
6.5 % or more at engine speed of 2000 rpm
(Conditions vary with engine speed)

TYPICAL MALFUNCTION THRESHOLDS

[OFF malfunction]
  1. All of the following conditions are met: OFF malfunctions (A), (B) and (C)
    2 detections are necessary in 1 driving cycle.
    1st detection: Temporary flag ON
    2nd detection: Pending fault code ON

OFF malfunction (A) 
Input speed/Output speed (NC0/SP2)
2.63 to 3.20
(This means actual gear is 1st)

OFF malfunction (B) 
Input speed/Output speed (NC0/SP2)
0.00 to 0.22
(This means actual gear is 4th)

OFF malfunction (C) 
Input speed/Output speed (NC0/SP2)
0.00 to 0.22
(This means actual gear is 4th)
[ON malfunction]
  1. All of the following conditions are met: ON malfunctions (A), (B) and (C)

ON malfunction (A) 
Input speed/Output speed (NC0/SP2)
1.40 to 1.67
(This means actual gear is 2nd)

ON malfunction (B) 
Input speed/Output speed (NC0/SP2)
0.93 to 1.07
(This means actual gear is 3rd)

ON malfunction (C) 
Input speed/Output speed (NC0/SP2)
0.93 to 1.07
(This means actual gear is 3rd)

INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).


ACTIVE TEST

HINT:
Using Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. Follow the instructions on the Techstream and perform the Active Test.

    HINT:
    While driving, the shift position can be changed with Techstream.
    Comparing the shift position directed by the Active Test with the actual shift position enables you to confirm the problem (Click here).


    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Shift Position
    Operate shift solenoid valve and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of shift solenoid valves
    [Vehicle Condition]
    50 km/h (30 mph) or less

    HINT:
    1. This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
    2. The 3rd to 4th up-shift must be performed with the accelerator pedal released.
    3. The 4th to 3rd down-shift must be performed with the accelerator pedal released.
    4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
    5. The shift position directed by the ECM is shown in the Data List display on the Techstream.
    6. The shift solenoid valve S2 is turned ON/OFF normally when the shift lever is in the D position:

      Gear shift controlled by ECM
      1st
      2nd
      3rd
      4th
      Shift solenoid valve S2
      OFF
      ON
      ON
      OFF

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0756)
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using Techstream.

Result 
Result
Proceed to
Only P0756 is output
A
P0756 and other DTCs are output
B

HINT:
If any codes besides P0756 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT SHIFT SOLENOID VALVE S2
G022784E02
  1. Remove the shift solenoid valve S2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    Solenoid Connector (S2) - Solenoid Body (S2)
    11 to 15 Ω at 20°C (68°F)

  1. Connect the battery's positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.

    OK:
    Valve moves and makes an operating noise.



NG
REPLACE SHIFT SOLENOID VALVE S2
OK


3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly (Click here).

    OK:
    There are no foreign objects on any valves and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)