DTC P2757 Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) |

| DTC No. | DTC Detection Conditions | Trouble Areas |
| P2757 | Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h (50 mph)), or lock-up remains ON in the lock-up OFF range. (2-trip detection logic) |
|
| Related DTCs | P2757: Shift solenoid valve SLU/OFF malfunction Shift solenoid valve SLU/ON malfunction |
| Required sensors/Components | Shift solenoid valve SLU |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (A): 2 seconds OFF malfunction (B): 1 second ON malfunction (A) and (B): 1.8 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | P0973, P0974 (Shift solenoid valve S1 circuit) P0976, P0977 (Shift solenoid valve S2 circuit) P0128 (ECT (Engine coolant temperature) sensor circuit) P0722 (Output speed sensor circuit) P0500 (Vehicle speed sensor circuit) P2759 (Torque converter clutch pressure control solenoid circuit) |
| Transmission shift position | "D" |
| Duration time from shifting "N" to "D" | 4 seconds or more |
| ECT (Engine Coolant Temperature) | 40°C (104°F) or more |
| Spark advance from max. retard timing by knock control | 0°CA or more |
| Engine | Starting |
| ECM selected gear | 3rd or 4th |
| Vehicle speed | 25 km/h (15.5 mph) or more |
| ECM lock-up command | ON (SLU pressure: 90 % or more) |
| Vehicle speed | Less than 100 km/h (62.1 mph) |
| ECM selected gear | 2nd |
| Vehicle speed | 10 km/h (6.2 mph) or more |
| Output speed | 2nd → 1st down-shift point or more |
| Throttle valve opening angle | 6.5% or more at 2000 rpm (Conditions vary with engine speed) |
| ECM lock-up command | OFF (SLU pressure: 10 % or less) |
| Throttle valve opening angle | 10 % or more |
| Vehicle speed | Less than 60 km/h (37.3 mph) |
| Engine speed - Output speed x 4th gear ratio | 70 rpm or more |
| Input speed / Output speed | Less than 2.63, or more than 3.20 |
| Engine speed - Input speed | Less than 35 rpm |
| Engine speed - Output speed x 4th gear ratio | Less than 35 rpm |
| Speed sensor (NCO) | Input speed is equal to engine speed when lock-up is ON. |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Lock Up | Control shift solenoid SLU to set automatic transmission to lock-up condition | ON or OFF | Possible to check shift solenoid valve SLU operation [Vehicle Condition]
|
Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.

| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2757) |
Connect Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using Techstream.
| Result | Proceed to |
| Only P2757 is output | A |
| P2757 and other DTCs are output | B |
|
| ||||
| A | |
| 2.INSPECT SHIFT SOLENOID VALVE SLU |
![]() |
Remove the shift solenoid valve SLU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| 1 - 2 | 5.1 to 5.5 Ω at 20°C (68°F) |
Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.
|
| ||||
| OK | |
| 3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | |
| 4.INSPECT TORQUE CONVERTER ASSEMBLY |
Check the torque converter assembly (Click here).
|
| ||||
| OK | ||
| ||