DTC P0751 Shift Solenoid "A" Performance (Shift Solenoid Valve S1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0751 | S1 stuck ON malfunction*1: The ECM determines that there is a malfunction when both of the following conditions are met: (a) When the ECM directs the transmission to switch to 4th gear, the engine overruns (clutch slips). (b) When the ECM directs the transmission to switch to 4th gear, the actual gear is shifted to 1st. |
|
| P0751 | S1 stuck OFF malfunction*2: The ECM determines that there is a malfunction when both of the following conditions are met: (a) When the ECM directs the transmission to switch to 1st gear, the actual gear is shifted to 4th. (b) When the ECM directs the transmission to switch to 4th gear, the actual gear is also shifted to 4th. |
|
| Gear shift controlled by ECM | 1st | 2nd | 3rd | 4th |
|
*1: Actual gear position under S1 stuck ON malfunction | 1st | 2nd | 2nd | 1st |
|
*2: Actual gear position under S1 stuck OFF malfunction | 4th | 3rd | 3rd | 4th |
| Related DTCs | P0751: Shift solenoid valve S1/OFF malfunction Shift solenoid valve S1/ON malfunction |
| Required sensors/Components | Shift solenoid valve S1, Speed sensor (SP2), Speed sensor (NCO), Crankshaft position sensor (NE), Throttle position sensor, MAF |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (A): 1 second OFF malfunction (B): 0.4 seconds ON malfunction (A): 0.8 seconds ON malfunction (B): Immediate |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | P0973, P0974 (Shift solenoid valve S1 circuit) P0976, P0977 (Shift solenoid valve S2 circuit) P0128 (ECT (Engine coolant temperature) sensor circuit) P0722 (Output speed sensor circuit) P0500 (Vehicle speed sensor circuit) |
| Transmission shift position | "D" |
| Duration time from shifting "N" to "D" | 4 seconds or more |
| ECT (Engine Coolant Temperature) | 40°C (104°F) or more |
| Spark advance from max. retard timing by knock control | 0°CA or more |
| Engine | Starting |
| ECM selected gear | 1st |
| Vehicle speed | 10 km/h (6.2 mph) or more and Less than 40 km/h (24.8 mph) |
| Throttle valve opening angle | 15 % or more and 6.5 % or more at engine speed of 2000 rpm (Conditions vary with engine speed) |
| Current ECM selected gear | 4th |
| Last ECM selected gear | 3rd |
| Actual gear when ECM selected 3rd gear | 3rd |
| ECM selected gear | 4th |
| Vehicle speed at current ECM selected gear - Vehicle speed at last ECM selected gear | Less than 10 km/h (6.2 mph) |
| Throttle valve opening angle at current ECM selected gear - Throttle valve opening angle at last ECM selected gear | Less than 10 % |
| Throttle valve opening angle | Less than 20 % |
| Vehicle speed | Less than 85 km/h (52.8 mph) |
| Engine speed | 3200 rpm or more |
| Current ECM selected gear | 4th |
| Last ECM selected gear | 3rd |
| Input speed/Output speed (NC0/SP2) | 0.00 to 0.22 (This means actual gear is 4th) |
| NE current - NE last NE current: Engine speed at current ECM selected gear NE last: Engine speed at last ECM selected gear | 950 rpm or more |
| Input speed/Output speed (NC0/SP2) | Does not change as follows 0.93 to 1.07 (This means actual gear is 3rd) ↓ 0.00 to 0.22 (This means actual gear is 4th) |
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | Operate shift solenoid valve and set each shift position |
| Possible to check operation of shift solenoid valves [Vehicle Condition] 50 km/h (30 mph) or less |
| Gear shift controlled by ECM | 1st | 2nd | 3rd | 4th |
| Shift solenoid valve S1 | ON | ON | OFF | OFF |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0751) |
Connect Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using Techstream.
| Result | Proceed to |
| Only P0751 is output | A |
| P0751 and other DTCs are output | B |
|
| ||||
| A | |
| 2.INSPECT SHIFT SOLENOID VALVE S1 |
![]() |
Remove the shift solenoid valve S1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| Solenoid Connector (S1) - Solenoid Body (S1) | 11 to 15 Ω at 20°C (68°F) |
Connect the battery's positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.
|
| ||||
| OK | |
| 3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | ||
| ||