DTC P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) |
DTC P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1) |
DTC P2197 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1) |
DTC P2198 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2195 P2197 | Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic)
|
|
| P2195 P2197 | While fuel-cut operation performed (during vehicle deceleration), air fuel ratio sensor current 2.2 mA or more for 3 seconds (2 trip detection logic) |
|
| P2196 P2198 | Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic)
|
|
| P2196 P2198 | While fuel-cut operation performed (during vehicle deceleration), air fuel ratio sensor current below 0.7 mA for 3 seconds (2 trip detection logic) |
|

| Related DTCs | P2195: Air fuel ratio sensor (bank 1 sensor 1) signal stuck lean P2196: Air fuel ratio sensor (bank 1 sensor 1) signal stuck rich P2197: Air fuel ratio sensor (bank 2 sensor 1) signal stuck lean P2198: Air fuel ratio sensor (bank 2 sensor 1) signal stuck rich |
| Required Sensors/Components (Main) | Air fuel ratio sensor (bank 1, 2 sensor 1) |
| Required Sensors/Components (Related) | Heated oxygen sensor |
| Frequency of Operation | Continuous |
| Duration | 5 seconds: Sensor voltage detection monitor 3 seconds: Sensor current detection monitor |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | P0016, P0018 (VVT system - misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0128 (Thermostat) P0171, P0172, P0174, P0175 (Fuel system) P0301, P0302, P0303, P0304, P0305, P0306 (Misfire) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0412, P0418, P1613 (Secondary air injection system control) P0416, P0417, P2440, P2441, P2442, P2443, P2444, P2445 (Secondary air injection system) P0451, P0452, P0453 (EVAP system) P0500, P0722 (Vehicle speed sensor) P0505 (Idle speed control) |
| Time after engine start | 30 seconds or more |
| Air fuel ratio sensor status | Activated |
| Fuel system status | Closed loop |
| Battery voltage | 11 V or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or higher |
| Air fuel ratio sensor status | Activated |
| Continuous time of fuel cut | 3 to 10 seconds |
| Heated oxygen sensor voltage | 0.21 V or more |
| Air fuel ratio sensor voltage | More than 3.8 V |
| Heated oxygen sensor voltage | Less than 0.66 V |
| Air fuel ratio sensor voltage | Less than 2.8 V |
| Air fuel ratio sensor current | 2.2 mA or more |
| Air fuel ratio sensor current | Less than 0.7 mA |


| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, P2197 OR P2198) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P2195, P2196, P2197 or P2198 is output | A |
| "DTC P2195, P2196, P2197 or P2198" and "DTC P0136, P0137, P0138, P0156, P0157 or P0158" are output | A |
| DTC P2195, P2196, P2197 or P2198 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CONFIRM WHETHER VEHICLE HAS RUN OUT OF FUEL IN PAST |
Has the vehicle run out of fuel in the past?
|
| ||||
| YES | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195, P2196, P2197 or P2198.
Check the DTC judgment.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2195, P2196, P2197 or P2198 are output) | B |
|
| ||||
| A | ||
| ||
| 4.READ VALUE USING TECHSTREAM (TEST VALUE OF AIR FUEL RATIO SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Current.
Check that the status of O2 Sensor is Complete.
If the status is still Incomplete, drive the vehicle according to the driving pattern again.
Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Details / RANGE B1S1 or RANGE B2S1.
Check the test value of the air fuel ratio sensor output current during fuel-cut.
| Result | Proceed to |
| Within normal range (0.7 mA or higher, and below 2.2 mA) | A |
| Outside normal range (Below 0.7 mA, or 2.2 mA or higher) | B |
|
| ||||
| A | |
| 5.READ VALUE USING TECHSTREAM (CONTROL THE INJECTION VOLUME) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Perform the Control the Injection Volume operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the air fuel ratio sensor and the heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.
| Techstream Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 AFS Voltage B2S1 (Air fuel ratio sensor) | +12% | Rich | Below 3.1 V |
| -12% | Lean | Higher than 3.4 V | |
| O2S B1S2 O2S B2S2 (Heated oxygen sensor) | +12% | Rich | Higher than 0.55 V |
| -12% | Lean | Below 0.4 V |
| Status of AFS Voltage B1S1 or AFS Voltage B2S1 | Status of O2S B1S2 or O2S B2S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition | Proceed to |
| Lean | Lean | Actual air fuel ratio lean | A |
| Rich | Rich | Actual air fuel ratio rich | A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | B |
| Lean/Rich | Lean/Rich | Normal | B |
|
| ||||
| A | |
| 6.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks.
|
| ||||
| OK | |
| 7.CHECK EXHAUST GAS LEAK |
Check the exhaust gas leaks.
|
| ||||
| OK | |
| 8.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 9.INSPECT FUEL INJECTOR ASSEMBLY |
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 10.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 11.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195, P2196, P2197 or P2198.
Check the DTC judgment.
| Result | Proceed to |
| ABNORMAL (DTC P2195, P2196, P2197 or P2198 are output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 12.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195, P2196, P2197 or P2198.
Check the DTC judgment.
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| NEXT | ||
| ||
| 14.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 15.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195, P2196, P2197 or P2198.
Check the DTC judgment.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2195, P2196, P2197 or P2198 are output) | B |
|
| ||||
| A | ||
| ||
| 16.CHECK FUEL LINE |
Check the fuel lines for leaks or blockage (Click here).
|
| ||||
| OK | ||
| ||