Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)

DTC    C1405    Open or Short in Front Speed Sensor RH Circuit

DTC    C1406    Open or Short in Front Speed Sensor LH Circuit

for Preparation Click here


DESCRIPTION

Refer to DTCs C1401 and C1402 .

DTC Code
DTC Detection Condition
Trouble Area
C1405
C1406
Either condition is met:
  1. An open in the speed sensor signal circuit continues for 0.5 seconds or more.
  2. With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.
  1. Front speed sensor RH/LH
  2. Skid control sensor wire
  3. Speed sensor circuit
  4. Skid control ECU (master cylinder solenoid)

HINT:
  1. DTC C1405 is for the front speed sensor RH.
  2. DTC C1406 is for the front speed sensor LH.


WIRING DIAGRAM


C217214E28


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (master cylinder solenoid), perform calibration (Click here).
  2. Check the speed sensor signal after replacement (Click here).

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Speed Open
    Front speed sensor RH open detection/ Error or Normal
    Normal
    -
    FL Speed Open
    Front speed sensor LH open detection/ Error or Normal
    Normal
    -

    OK:
    Normal (there are no momentary interruptions).

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 4
OK


2.READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Front wheel speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.
    FL Wheel Speed
    Front wheel speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the Techstream is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 4
OK


3.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTCs C1405 and C1406 are not output
    A
    DTCs C1405 and/or C1406 are output
    B



B
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

4.INSPECT SKID CONTROL SENSOR WIRE
  1. Remove the skid control sensor wire.



    C214500E10
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    RH 
    Tester Connection
    Condition
    Specified Condition
    S4-1 - Va1-1 (FR-)
    Always
    Below 1 Ω
    S4-2 - Va1-2 (FR+)
    Always
    Below 1 Ω
    S4-1 - S4-2
    Always
    10 kΩ or higher
    LH 
    Tester Connection
    Condition
    Specified Condition
    S3-1 - Wa1-1 (FL-)
    Always
    Below 1 Ω
    S3-2 - Wa1-2 (FL+)
    Always
    Below 1 Ω
    S3-1 - S3-2
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Skid Control Sensor Wire
    *a
    RH
    *b
    LH



NG
REPLACE SKID CONTROL SENSOR WIRE
OK


5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
  1. Install the skid control sensor wire.

  1. Disconnect the S1 skid control ECU (master cylinder solenoid) connector.

  1. Disconnect the Va1 and/or Wa1 front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    RH 
    Tester Connection
    Condition
    Specified Condition
    S1-3 (FR+) - Va1-2 (FR+)
    Always
    Below 1 Ω
    S1-3 (FR+) - Body ground
    Always
    10 kΩ or higher
    S1-17 (FR-) - Va1-1 (FR-)
    Always
    Below 1 Ω
    S1-17 (FR-) - Body ground
    Always
    10 kΩ or higher
    LH 
    Tester Connection
    Condition
    Specified Condition
    S1-18 (FL+) - Wa1-2 (FL+)
    Always
    Below 1 Ω
    S1-18 (FL+) - Body ground
    Always
    10 kΩ or higher
    S1-4 (FL-) - Wa1-1 (FL-)
    Always
    Below 1 Ω
    S1-4 (FL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT SKID CONTROL ECU (FR+, FL+ TERMINAL)
  1. Disconnect the Va1 and/or Wa1 front speed sensor connector.

  1. Connect the S1 skid control ECU (master cylinder solenoid) connector.



    C207217E17
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    RH 
    Tester Connection
    Switch Condition
    Specified Condition
    Va1-2 (FR+) - Body ground
    Ignition switch ON
    11 to 14 V
    LH 
    Tester Connection
    Switch Condition
    Specified Condition
    Wa1-2 (FL+) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Front Speed Sensor)
    *b
    RH
    *c
    LH



NG
REPLACE MASTER CYLINDER SOLENOID (Click here)
OK

REPLACE FRONT SPEED SENSOR (Click here)