Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0327    Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

DTC    P0328    Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

for Preparation Click here


DESCRIPTION

A flat type knock sensor (non-resonant type) has a structure that can detect vibrations between approximately 5 kHz and 15 kHz.
Knock sensors are fitted onto the engine block to detect engine knocking.
The knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.
The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No.
DTC Detection Condition
Trouble Area
P0327
Output voltage of knock sensor less than 0.5 V
(1 trip detection logic)
  1. Short in knock sensor circuit
  2. Knock sensor
  3. ECM
P0328
Output voltage of knock sensor higher than 4.5 V
(1 trip detection logic)
  1. Open in knock sensor circuit
  2. Knock sensor
  3. ECM

HINT:
When any of DTCs P0327 and P0328 are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.


  1. A085286E88
    Reference: Inspection using an oscilloscope
    The correct waveform is shown.
    ECM Terminal Name
    Between KNK1 and EKNK
    Tester Range
    1 V/DIV., 1 ms./DIV.
    Condition
    Engine speed maintained 4000 rpm after warming up engine

MONITOR DESCRIPTION

If the output voltage transmitted by the knock sensor remains low or high for more than 1 second, the ECM interprets this as a malfunction in the sensor circuit, and stores the DTC.
The monitor for DTCs P0327 and P0328 begins to run when 5 seconds have elapsed since the engine was started.
If the malfunction is not repaired successfully, any of DTC P0327 or P0328 is stored 5 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0327: Knock Sensor Range Check (Low Voltage)
P0328: Knock Sensor Range Check (High Voltage)
Required Sensors/Components (Main)
Knock sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
1 second
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Battery voltage
10.5 V or higher
Time after engine start
5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


Knock Sensor Range Check (Low voltage) P0327 
Knock sensor voltage
Less than 0.5 V

Knock Sensor Range Check (High voltage) P0328 
Knock sensor voltage
Higher than 4.5 V

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine and wait 5 minutes.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  8. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0327 or P0328.
  11. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.

  12. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A236393E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
A065743E22
  1. Disconnect the E4 ECM connector.

  1. Measure the resistance between the terminals of the ECM connector.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E4-29 (KNK1) - E4-30 (EKNK)
    20°C (68°F)
    120 to 280 kΩ



NG
Go to step 3
OK


2.INSPECT ECM (KNK1 VOLTAGE)
G038298E02
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage between the ECM terminals.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E4-29 (KNK1) - E4-30 (EKNK)
    Ignition switch ON
    4.5 to 5.5 V



NG
REPLACE ECM (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

3.INSPECT KNOCK SENSOR
A065174E09
  1. Remove the knock sensor.

  1. Measure the resistance between the terminals.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K1-2 (KNK1) - K1-1 (EKNK)
    20°C (68°F)
    120 to 280 kΩ



NG
REPLACE KNOCK SENSOR (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - KNOCK SENSOR)