DTC P0451 Evaporative Emission Control System Pressure Sensor Range / Performance |
DTC P0452 Evaporative Emission Control System Pressure Sensor / Switch Low Input |
DTC P0453 Evaporative Emission Control System Pressure Sensor / Switch High Input |
| DTC No. | Monitoring Item | Malfunction Detection Condition | Trouble Area | Detection Timing | Detection Logic |
| P0451 | Canister pressure sensor noise | Sensor output voltage fluctuates frequently within certain time period. |
|
| 2 trip |
| Canister pressure sensor signal becomes fixed/flat | Sensor output voltage does not vary within certain time period. | ||||
| P0452 | Canister pressure sensor voltage low | Sensor output less than 42.11 kPa(abs) [315.85 mmHg(abs)] for 0.5 seconds. |
| 1 trip | |
| P0453 | Canister pressure sensor voltage stuck | Sensor output more than 123.761 kPa(abs) [928.28 mmHg(abs)] for 0.5 seconds. |

| Required Sensors/Components | Canister pump module |
| Frequency of Operation | Once per driving cycle: P0451 sensor stuck Continuous: P0451 sensor noise, P0452 and P0453 |
| Duration | 0.5 seconds: P0452 and P0453 Within 2 minutes: P0451 (sensor stuck) Within 15 seconds: P0451 (sensor noise) |
| MIL Operation | Immediate: P0452 and P0453 2 driving cycles: P0451 |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Atmospheric pressure (absolute pressure) | 70 to 110 kPa(abs) [525 to 825 mmHg(abs)] |
| Battery voltage | 10.5 V or more |
| Intake air temperature | 4.4° to 35°C (40° to 95°F) |
| Canister pressure sensor malfunction (P0452, 0453) | Not detected |
| Either of following conditions met | A or B |
| A. Engine condition | Running |
| B. Time after key-off | 5 or 7 or 9.5 hours |
| Monitor runs whenever following DTCs not present | None |
| Battery voltage | 10.5 V or more |
| Intake air temperature | 4.4° to 35°C (40° to 95°F) |
| Canister pressure sensor malfunction (P0452, 0453) | Not detected |
| Atmospheric pressure (absolute pressure) | 70 to 110 kPa(abs) [525 to 825 mmHg(abs)] |
| Time after key-off | 5 or 7 or 9.5 hours |
| Monitor runs whenever following DTCs not present | None |
| Either of following conditions met | (a) or (b) |
| (a) Ignition switch | ON |
| (b) Soak timer | ON |
| Frequency that EVAP pressure change 0.3 kPa(gauge) [2.25 mmHg(gauge)] or more | 10 times or more in 10 seconds |
| EVAP pressure change during reference pressure | Less than 0.65 kPa(gauge) [4.87 mmHg(gauge)] |
| EVAP pressure | Less than 42.11 kPa(abs) [315.85 mmHg(abs)] |
| EVAP pressure | More than 123.761 kPa(abs) [928.28 mmHg(abs)] |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CONFIRM DTC AND EVAP PRESSURE |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (do not start the engine).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
Enter the following menus: Powertrain / Engine and ECT / Data List / Vapor Pressure Pump.
Read the EVAP (Evaporative Emission) pressure displayed on the Techstream.
| Display (DTC Output) | Test Result | Suspected Trouble Area | Proceed to |
| P0451 | - | Canister pressure sensor | C |
| P0452 | Less than 42.11 kPa (315.85 mmHg) |
| A |
| P0453 | More than 123.761 kPa (928.28 mmHg) |
| B |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
Turn the ignition switch off.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Test Result | Suspected Trouble Area | Proceed to |
| E8-31 (PPMP) - Body ground | Always | Below 10 Ω |
| A |
| 10 kΩ or higher |
| B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
Disconnect the canister pump module connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Test Result | Suspected Trouble Area | Proceed to |
| E8-31 (PPMP) - Body ground | Always | Below 10 Ω | Wire harness/connector (ECM - canister pressure sensor) | A |
| 10 kΩ or higher | Short in canister pressure sensor circuit | B |
|
| ||||
|
| ||||
| 4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
![]() |
Disconnect the canister pump module connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L1-2 (SGND) - Body ground | Always | 100 Ω or less |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L1-4 (VCC) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| L1-3 (VOUT) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Canister Pump Module) |
| Test Result | Suspected Trouble Area | Proceed to |
| Voltage and resistance within standard ranges | Open in canister pressure sensor circuit | A |
| Voltage and resistance outside standard ranges | Open in wire harness/connector (ECM - Canister pressure sensor) | B |
|
| ||||
|
| ||||
| 5.REPLACE CANISTER PUMP MODULE |
Replace the canister pump module (Click here).

| *1 | Fuel Tank Vent Hose | *2 | Air Inlet Port |
| *3 | Vent hose | *4 | Fuel Tank |
| *5 | Canister Pump Module | *6 | Canister Assembly |
| *7 | Canister Filter | - | - |
| *a | Inspection Area (Check for Disconnection and/or Crack) | - | - |
|
| ||||
| 6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM) |
|
| ||||
| 7.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0451, P0452 or P0453.
Check the DTC judgment result.
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| NEXT | ||
| ||